Lowrance electronic LMF-200 manual Accessory Ordering Information for all countries

Page 71

Accessory Ordering Information for all countries

To order Lowrance accessories such as power cables or transducers, please contact:

1)Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.

To locate a Lowrance dealer near you, visit our web site, www.lowrance.com and look for the Dealer Locator. Or, you can consult your telephone directory for listings.

2)U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129 Call 1-800-324-0045 or visit our web site www.lei-extras.com.

3)Canadian customers can write:

Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario L4W2R7 or fax 905-629-3118.

Shipping Information

If it becomes necessary to send a product for repair or replacement, you must first receive a return authorization number from Customer Service. Products shipped without a return authorization will not be accepted. When shipping, we recommend you do the following:

1.Please do not ship the knobs or mounting bracket with your unit.

2.If you are sending a check for repair, please place your check in an envelope and tape it to the unit.

3.For proper testing, include a brief note with the product describing the problem. Be sure to include your name, return shipping address and a daytime telephone number. An e-mail address is optional but useful.

4.Pack the unit in a suitable size box with packing material to prevent any damage during shipping.

5.Write the Return Authorization (RA) number on the outside of the box underneath your return address.

6.For your security, you may want to insure the package through your shipping courier. Lowrance does not assume responsibility for goods lost or damaged in transit.

Image 71
Contents LMF-200 Visit our web site Copyright 2006 Lowrance Electronics, Inc All rights reservedTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Recommended Tools and Supplies PreparationMounting the Gauge Installation SequenceWiring LMF-200 cable connections Network Backbone and Network Nodes Connecting to a Nmea 2000 NetworkCompatibility Adding a Network Node Additional Network Information Menu key Menu CommandsUnderstanding this Manual Up and Down keysTo execute Boat Setup Boat SetupPages TimeoutBasic Menu Options Viewing Pages Page Screen RotationPages Menu Autoscroll To add a page to the displayRemove To remove a page from the displayTo set Stay Time Pop-ups SetupTo set a Pop-Up Stay TimePop-up Thresholds RPM Threshold set upEngine Trim Threshold set up Trim Tabs Threshold set upBacklight Rudder Threshold set upTo adjust Backlight ScreenReverse Video Rev Video Audio SetupTo adjust Contrast ContrastSystem Setup Menu To set the Deep Alarm Sonar AlarmsTo set the Shallow Alarm To reset values TimeoutTo reset Eng/Tank configuration ResetSystem Information To access the Nmea Information screenTo access System Information screen Nmea InfoPressure Range To set Engine WarningsSpeed Range To set Speed RangeTo change Speed and Distance units To set Pressure RangeUnits To change GPS units To change Temperature unitsTo change Pressure units To change Depth unitsTo refill tank Fuel SetupTo change Volume units Refill Tank Refill TFuel Remaining Source FRem Src To use Partial FillEconomy Speed Eco spd To change Economy Speed SourceCustomizing Pages To customize the Single Digital To Customize the Gauge To customize the Dual DigitalTo Customize Trim Tabs To Customize the Fuel ManagerTo configure EP-35 Temp Sensor EP-35 Temperature ConfigurationIf all temps configured Configuration name unavailable To unconfigure EP-35 temp sensorTo reconfigure an EP-35 temp sensor If desired configuration name available EP-10 Fuel Flow ConfigurationTo unconfigure an EP-10 Fuel Flow To configure Fuel FlowIf all fuel flows configured Configuration name unavailable To reconfigure an EP-10 Fuel FlowIf configuration name available Fluid Level menu EP-15 Fluid Level ConfigurationTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To reconfigure EP-15 Fluid Level To unconfigure EP-15 Fluid LevelTo set a Level Warning To execute Reset commandLevel Warning To configure Suzuki Engine Interface Suzuki Engine Interface ConfigurationTo reconfigure a Suzuki Engine Interface To unconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Fuel Flow Accuracy Calibrating EP SensorsEP-10 Fuel Flow Calibration To calibrate an EP-10 Fuel Flow Refill TankPartial Fill Reset CalibrationTo execute Reset Calibration command To execute 2-Point calibration EP-15 Fluid Level CalibrationTo execute 3-Point calibration Point CalibrationTo execute 5-Point calibration Engine Interface Accuracy To Reset CalibrationCalibrating Fuel Flow in a Suzuki Engine Interface To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service…Accessory Ordering Information for all countries Visit our web site