Lowrance electronic LMF-200 manual Fuel Warning

Page 53

3.Highlight PORT ENG and press MENU. Select CHANGE ENGINE and press MENU, which will open the Select Engine menu with up to three options (Port, Center and Starboard), depending on your engine-tank configuration.

4.Highlight STARBOARD and press MENU.

5.You will be taken back to the Bus Devices list, where the engine interface you selected (formerly Port Eng) will now be displayed as Stbd Eng. If the newly configured interface is not shown, refresh the Bus Devices list.

Fuel Warning:

The Fuel Warning allows you to set a Low Level or High Level alarm for each Suzuki Engine Interface on the network. A pop-up window will appear if fuel rises above or falls below a threshold of your choosing.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. After a few moments, the Bus Devices list will appear.

3.Select an engine interface and press MENU.

4.Highlight FUEL WRNG and press MENU. The Select Level menu will appear with two options: Low Level and High Level.

5.Select LOW LEVEL and press MENU, which will open the Level Percentage window. It will be set to Off by default. To set the Fuel Warning to High Level Repeat steps 1-4, then select HIGH LEVEL from the Select Level menu.

6.Use the UP and DOWN keys to set the desired fuel warning percentage and press MENU. You will be taken back to the Bus Devices list.

NOTE:

To see fuel remaining information from the Suzuki Engine Interface, you must change the Fuel Remaining Source to Eng/FFlow. See page 28.

Reset:

The Reset command in the engine interface menu allows you to reset configuration and calibration settings for a particular interface.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. The Bus Devices list will appear.

47

Image 53

Contents LMF-200 Visit our web site Copyright 2006 Lowrance Electronics, Inc All rights reservedTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Recommended Tools and Supplies PreparationMounting the Gauge Installation SequenceWiring LMF-200 cable connections Network Backbone and Network Nodes Connecting to a Nmea 2000 NetworkCompatibility Adding a Network Node Additional Network Information Understanding this Manual Menu CommandsUp and Down keys Menu keyTo execute Boat Setup Boat SetupPages TimeoutBasic Menu Options Viewing Pages Page Screen RotationPages Menu Remove To add a page to the displayTo remove a page from the display AutoscrollTo set a Pop-Up Pop-ups SetupStay Time To set Stay TimeEngine Trim Threshold set up RPM Threshold set upTrim Tabs Threshold set up Pop-up ThresholdsTo adjust Backlight Rudder Threshold set upScreen BacklightTo adjust Contrast Audio SetupContrast Reverse Video Rev VideoSystem Setup Menu To set the Deep Alarm Sonar AlarmsTo set the Shallow Alarm To reset Eng/Tank configuration TimeoutReset To reset valuesTo access System Information screen To access the Nmea Information screenNmea Info System InformationSpeed Range To set Engine WarningsTo set Speed Range Pressure RangeTo change Speed and Distance units To set Pressure RangeUnits To change Pressure units To change Temperature unitsTo change Depth units To change GPS unitsTo change Volume units Fuel SetupRefill Tank Refill T To refill tankEconomy Speed Eco spd To use Partial FillTo change Economy Speed Source Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To Customize the Gauge To customize the Dual DigitalTo Customize Trim Tabs To Customize the Fuel ManagerTo configure EP-35 Temp Sensor EP-35 Temperature ConfigurationIf all temps configured Configuration name unavailable To unconfigure EP-35 temp sensorTo reconfigure an EP-35 temp sensor If desired configuration name available EP-10 Fuel Flow ConfigurationTo unconfigure an EP-10 Fuel Flow To configure Fuel FlowIf all fuel flows configured Configuration name unavailable To reconfigure an EP-10 Fuel FlowIf configuration name available Fluid Level menu EP-15 Fluid Level ConfigurationTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To reconfigure EP-15 Fluid Level To unconfigure EP-15 Fluid LevelTo set a Level Warning To execute Reset commandLevel Warning To configure Suzuki Engine Interface Suzuki Engine Interface ConfigurationTo reconfigure a Suzuki Engine Interface To unconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Fuel Flow Accuracy Calibrating EP SensorsEP-10 Fuel Flow Calibration To calibrate an EP-10 Fuel Flow Refill TankPartial Fill Reset CalibrationTo execute Reset Calibration command To execute 2-Point calibration EP-15 Fluid Level CalibrationTo execute 3-Point calibration Point CalibrationTo execute 5-Point calibration Engine Interface Accuracy To Reset CalibrationCalibrating Fuel Flow in a Suzuki Engine Interface To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service…Accessory Ordering Information for all countries Visit our web site