Lowrance electronic LMF-200 manual Sonar Alarms, To set the Shallow Alarm, To set the Deep Alarm

Page 27

3.To select an item from the bus devices list, use the UP and DOWN keys to highlight the device and press MENU. To get back to the main display, let the menu time out. Accessing devices from the Bus Devices list gives you access to an EP sensor's internal menu. We will cover that in more detail in Section 4: EP Configuration and Calibration.

4.When you are through with the Bus Devices list, let the menu time out to be taken back to the main display.

Sonar Alarms

Sonar alarms allow you to set alarms that will alert you as water depth changes around your vessel. If the depth rises above (Deep Alarm) or falls below (Shallow Alarm) a depth threshold of your choosing, an alarm will sound.

To set the Shallow Alarm:

The shallow alarm will sound when your vessel enters water more shallow than the selected shallow alarm threshold.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight SNR ALARMS and press MENU. The Alarm menu will appear with two choices: Shallow and Deep.

3.Select SHALLOW and press MENU. The Shallow Alarm menu will appear with two options: Off and Set Depth. Select SET DEPTH and press MENU. (To turn off the Shallow Alarm, repeat Steps 1-3, then select Off from the Shallow menu.)

4.Use the UP and DOWN keys to set the desired depth. Press MENU and you will be taken back to the main display.

To set the Deep Alarm:

The deep alarm will sound when your vessel enters water deeper than the selected deep alarm threshold.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight SNR ALARMS and press MENU. The Alarm menu will appear with two options: Shallow and Deep.

3.Select DEEP and press MENU, which will open the Deep menu with two options: Off and Set Depth. (To turn off the Deep Alarm, repeat Steps 1-3, then select Off from the Deep menu.)

4.Select SET DEPTH, then use the UP and DOWN keys to set the alarm to the desired depth and press MENU. You will be taken back to the main display.

21

Image 27

Contents LMF-200 Visit our web site Copyright 2006 Lowrance Electronics, Inc All rights reservedTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Recommended Tools and Supplies PreparationMounting the Gauge Installation SequenceWiring LMF-200 cable connections Connecting to a Nmea 2000 Network CompatibilityNetwork Backbone and Network Nodes Adding a Network Node Additional Network Information Menu key Menu CommandsUnderstanding this Manual Up and Down keysTo execute Boat Setup Boat SetupTimeout Basic MenuPages Options Viewing Pages Page Screen RotationPages Menu Autoscroll To add a page to the displayRemove To remove a page from the displayTo set Stay Time Pop-ups SetupTo set a Pop-Up Stay TimePop-up Thresholds RPM Threshold set upEngine Trim Threshold set up Trim Tabs Threshold set upBacklight Rudder Threshold set upTo adjust Backlight ScreenReverse Video Rev Video Audio SetupTo adjust Contrast ContrastSystem Setup Menu Sonar Alarms To set the Shallow AlarmTo set the Deep Alarm To reset values TimeoutTo reset Eng/Tank configuration ResetSystem Information To access the Nmea Information screenTo access System Information screen Nmea InfoPressure Range To set Engine WarningsSpeed Range To set Speed RangeTo set Pressure Range UnitsTo change Speed and Distance units To change GPS units To change Temperature unitsTo change Pressure units To change Depth unitsTo refill tank Fuel SetupTo change Volume units Refill Tank Refill TFuel Remaining Source FRem Src To use Partial FillEconomy Speed Eco spd To change Economy Speed SourceCustomizing Pages To customize the Single Digital To Customize the Gauge To customize the Dual DigitalTo Customize Trim Tabs To Customize the Fuel ManagerTo configure EP-35 Temp Sensor EP-35 Temperature ConfigurationTo unconfigure EP-35 temp sensor To reconfigure an EP-35 temp sensorIf all temps configured Configuration name unavailable If desired configuration name available EP-10 Fuel Flow ConfigurationTo unconfigure an EP-10 Fuel Flow To configure Fuel FlowIf all fuel flows configured Configuration name unavailable To reconfigure an EP-10 Fuel FlowIf configuration name available Fluid Level menu EP-15 Fluid Level ConfigurationTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To reconfigure EP-15 Fluid Level To unconfigure EP-15 Fluid LevelTo execute Reset command Level WarningTo set a Level Warning To configure Suzuki Engine Interface Suzuki Engine Interface ConfigurationTo reconfigure a Suzuki Engine Interface To unconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Calibrating EP Sensors EP-10 Fuel Flow CalibrationFuel Flow Accuracy To calibrate an EP-10 Fuel Flow Refill TankReset Calibration To execute Reset Calibration commandPartial Fill To execute 2-Point calibration EP-15 Fluid Level CalibrationTo execute 3-Point calibration Point CalibrationTo execute 5-Point calibration To Reset Calibration Calibrating Fuel Flow in a Suzuki Engine InterfaceEngine Interface Accuracy To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service…Accessory Ordering Information for all countries Visit our web site