Lowrance electronic LMF-200 manual To configure Fuel Flow, To unconfigure an EP-10 Fuel Flow

Page 42

Devices list. To do this, let the menu time out and press MENU. Select SYSTEM SETUP and press MENU. Highlight B. DEVICES and press MENU. The Fuel Flow will be listed with its new configuration.

To configure Fuel Flow:

When you configure a fuel flow, you are linking the fuel flow's location/engine on the boat to its matching configuration/device name (Port, Center or Starboard) in the LMF-200.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. After a few moments, the Bus Devices list will appear, showing all LowranceNet devices detected on the network.

3.Select UNCFG FF and press MENU, which will open the Configuration options menu with up to three options: Port, Cen and Stbd. Select the desired location and press MENU. The following message will appear: Hit Menu to Cfg Flow Sns.

NOTE:

If your unit is set to a one-engine configuration, the Configuration Options menu will not appear when you are configuring a fuel flow. On the Bus Devices list, the fuel flow will automatically be given the configuration name Eng FFlow.

4.Press MENU, which, if you have more than one EP-10 Fuel Flow, will take you back to the configuration options menu. Configure the remaining fuel flows by following the steps above. If you have one fuel flow, you will be directed back to the Bus Devices list. Remember: If the fuel flow you just configured is not shown on the Bus Devices the list, you will have to refresh the list. Let the Bus Devices list time out, then access it again.

To unconfigure an EP-10 Fuel Flow:

If you want to reassign a fuel flow's configuration/device name in the LMF-200 or when you want to reconfigure an engine when all engines on your vessel are configured, you first will have to unconfigure a fuel flow.

Unset Engine:

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight B. DEVICES and press MENU. After a few moments, the Bus Devices list will appear, showing all LowranceNet devices detected on the network.

3.Select the fuel flow you want to unconfigure and press MENU.

36

Image 42

Contents LMF-200 Copyright 2006 Lowrance Electronics, Inc All rights reserved Visit our web siteTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Preparation Recommended Tools and SuppliesInstallation Sequence Mounting the GaugeWiring LMF-200 cable connections Connecting to a Nmea 2000 Network CompatibilityNetwork Backbone and Network Nodes Adding a Network Node Additional Network Information Up and Down keys Menu CommandsUnderstanding this Manual Menu keyBoat Setup To execute Boat SetupTimeout Basic MenuPages Viewing Pages Page Screen Rotation OptionsPages Menu To remove a page from the display To add a page to the displayRemove AutoscrollStay Time Pop-ups SetupTo set a Pop-Up To set Stay TimeTrim Tabs Threshold set up RPM Threshold set upEngine Trim Threshold set up Pop-up ThresholdsScreen Rudder Threshold set upTo adjust Backlight BacklightContrast Audio SetupTo adjust Contrast Reverse Video Rev VideoSystem Setup Menu Sonar Alarms To set the Shallow AlarmTo set the Deep Alarm Reset TimeoutTo reset Eng/Tank configuration To reset valuesNmea Info To access the Nmea Information screenTo access System Information screen System InformationTo set Speed Range To set Engine WarningsSpeed Range Pressure RangeTo set Pressure Range UnitsTo change Speed and Distance units To change Depth units To change Temperature unitsTo change Pressure units To change GPS unitsRefill Tank Refill T Fuel SetupTo change Volume units To refill tankTo change Economy Speed Source To use Partial FillEconomy Speed Eco spd Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To customize the Dual Digital To Customize the GaugeTo Customize the Fuel Manager To Customize Trim TabsEP-35 Temperature Configuration To configure EP-35 Temp SensorTo unconfigure EP-35 temp sensor To reconfigure an EP-35 temp sensorIf all temps configured Configuration name unavailable EP-10 Fuel Flow Configuration If desired configuration name availableTo configure Fuel Flow To unconfigure an EP-10 Fuel FlowTo reconfigure an EP-10 Fuel Flow If all fuel flows configured Configuration name unavailableIf configuration name available EP-15 Fluid Level Configuration Fluid Level menuTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To unconfigure EP-15 Fluid Level To reconfigure EP-15 Fluid LevelTo execute Reset command Level WarningTo set a Level Warning Suzuki Engine Interface Configuration To configure Suzuki Engine InterfaceTo unconfigure a Suzuki Engine Interface To reconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Calibrating EP Sensors EP-10 Fuel Flow CalibrationFuel Flow Accuracy Refill Tank To calibrate an EP-10 Fuel FlowReset Calibration To execute Reset Calibration commandPartial Fill EP-15 Fluid Level Calibration To execute 2-Point calibrationPoint Calibration To execute 3-Point calibrationTo execute 5-Point calibration To Reset Calibration Calibrating Fuel Flow in a Suzuki Engine InterfaceEngine Interface Accuracy To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site