Lowrance electronic LMF-200 manual To change Temperature units, To change Pressure units

Page 32

To change Temperature units:

Accessing Temperature from the Change Units menu will allow you to set the unit of measure for temperature to Fahrenheit or Celsius.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight UNITS and press MENU. Select TEMP and press MENU, which will launch the Temp menu with two options: Fahrenheit and Celsius.

3.Select the desired setting and press MENU. You will be taken back to the main display.

To change Pressure units:

Selecting Pressure from the Change Units menu will allow you to set the unit of measure for pressure to Imperial/US or SI/Metric.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight UNITS and press MENU. Select PRESSURE and press MENU, which will open the Pressure menu with two options: Imper (US) and SI (Metric).

3.Select the desired pressure setting and press MENU, which will direct you back to the main display.

To change Depth units:

Choosing Depth from the Change Units menu will allow you to set the unit of measure for depth to Feet, Fathoms or Meters.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight UNITS and press MENU. Select DEPTH and press MENU, which will launch the Depth Menu with three options: Feet, Fathoms and Meters.

3.Select the desired depth setting and press MENU, which will take you back to the main display.

To change GPS units:

Selecting GPS Coord from the Change Units menu will allow you to set the unit of measure for GPS coordinates to Deg/Min or Deg/Min/Sec.

1.Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press MENU.

2.Highlight UNITS and press MENU. Select GPS and press MENU, which will open the GPS menu with two options: Deg/Min or Deg/Min/Sec.

3.Select the desired GPS unit setting and press MENU. You will be directed back to the main display.

26

Image 32

Contents LMF-200 Copyright 2006 Lowrance Electronics, Inc All rights reserved Visit our web siteTable of Contents Backlight Sync BL Sync Iii Page Introduction Page Preparation Recommended Tools and SuppliesInstallation Sequence Mounting the GaugeWiring LMF-200 cable connections Network Backbone and Network Nodes Connecting to a Nmea 2000 NetworkCompatibility Adding a Network Node Additional Network Information Menu Commands Understanding this ManualUp and Down keys Menu keyBoat Setup To execute Boat SetupPages TimeoutBasic Menu Viewing Pages Page Screen Rotation OptionsPages Menu To add a page to the display RemoveTo remove a page from the display AutoscrollPop-ups Setup To set a Pop-UpStay Time To set Stay TimeRPM Threshold set up Engine Trim Threshold set upTrim Tabs Threshold set up Pop-up ThresholdsRudder Threshold set up To adjust BacklightScreen BacklightAudio Setup To adjust ContrastContrast Reverse Video Rev VideoSystem Setup Menu To set the Deep Alarm Sonar AlarmsTo set the Shallow Alarm Timeout To reset Eng/Tank configurationReset To reset valuesTo access the Nmea Information screen To access System Information screenNmea Info System InformationTo set Engine Warnings Speed RangeTo set Speed Range Pressure RangeTo change Speed and Distance units To set Pressure RangeUnits To change Temperature units To change Pressure unitsTo change Depth units To change GPS unitsFuel Setup To change Volume unitsRefill Tank Refill T To refill tankTo use Partial Fill Economy Speed Eco spdTo change Economy Speed Source Fuel Remaining Source FRem SrcCustomizing Pages To customize the Single Digital To customize the Dual Digital To Customize the GaugeTo Customize the Fuel Manager To Customize Trim TabsEP-35 Temperature Configuration To configure EP-35 Temp SensorIf all temps configured Configuration name unavailable To unconfigure EP-35 temp sensorTo reconfigure an EP-35 temp sensor EP-10 Fuel Flow Configuration If desired configuration name availableTo configure Fuel Flow To unconfigure an EP-10 Fuel FlowTo reconfigure an EP-10 Fuel Flow If all fuel flows configured Configuration name unavailableIf configuration name available EP-15 Fluid Level Configuration Fluid Level menuTo configure EP-15 Fluid Level for Fuel To configure EP-15 Fluid Level for Oil To unconfigure EP-15 Fluid Level To reconfigure EP-15 Fluid LevelTo set a Level Warning To execute Reset commandLevel Warning Suzuki Engine Interface Configuration To configure Suzuki Engine InterfaceTo unconfigure a Suzuki Engine Interface To reconfigure a Suzuki Engine InterfaceIf all interfaces configured Configuration name unavailable Fuel Warning Fuel Flow Accuracy Calibrating EP SensorsEP-10 Fuel Flow Calibration Refill Tank To calibrate an EP-10 Fuel FlowPartial Fill Reset CalibrationTo execute Reset Calibration command EP-15 Fluid Level Calibration To execute 2-Point calibrationPoint Calibration To execute 3-Point calibrationTo execute 5-Point calibration Engine Interface Accuracy To Reset CalibrationCalibrating Fuel Flow in a Suzuki Engine Interface To calibrate a Suzuki Engine Interface Refill Tank Reset Calibration Calibrating EP-30 Trim Tabs Page Page Page Appendix Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site