Dynacord 2200, CMS 1000, 1600 owner manual Display, 30. UP/DOWN, Peak LED, Effect Return

Page 14

EFFECTS 1/2

29. DISPLAY

The display always indicates the actual selected program number of the corresponding FX unit. The display screen is covered with a protective foil to prevent it from being damaged during shipment. Please remove the foil.

30. UP/DOWN

The UP/DOWN buttons are for selecting effect presets. Pressing and holding one of these lets you scroll through the program numbers.

31/32. FX1/2 to AUX3/4

These controls allow adding the output signal of FX1 or FX2 to the monitoring channel. Experience has revealed that the effect level in the monitor mix has to be lower than the level in the main mix, since the distance between monitor speakers and artists is much shorter.

33. FX ON

This switch switches an internal FX unit on and the green LED lights. Please keep in mind that you can also use an external footswitch for switching the FX unit ON. In this case, the LED also shows the actual operational status of the FX unit. If you want to use a footswitch, the FX ON switch has to be engaged first. The corresponding FX unit is activated and you can use the footswitch to switch the selected effect program on or off.

34. PFL

Engaging the PFL button routes the audio signal to the headphones bus, so that it is present at the phones output connector. The phones output volume is independent of the corresponding FX fader’s setting (PRE FADER LISTEN).

35. PEAK LED

These indicators signal if the internal FX units or the AUX 1/2 SEND signals are on the verge of clipping. To achieve an adequate S/N ratio, please adjust the FX units’ input level as follows:

Setting Instructions:

1. Establish a “dry” mix – without effect settings – according to the previous descriptions.

2. Position the effect return fader of the corresponding effect channel at the –5dB mark.

3. Use the UP/DOWN buttons to select the desired FX program preset.

4. Press the FX ON switch.

5.Play (start the reproduction of) the sound source connected to the desired input channel and adjust the desired amount of the FX signal, using the AUX/FX controls of this input channel.

Repeat this step for all input channels that you want to include in your effect mix.

6. Monitor the Peak LED so that it only lights frequently at highly dynamic signal peaks. When clipping occurs, reduce the AUX/FX controls in the channels.

7.Use the FX to AUX control to add the effect mix to the monitor mix.

In case you are using a different effect setting for the second FX unit, you have to repeat steps 2 - 7, respectively. Pay some attention to the peak indicators when operating your CMS to be able to quickly interact when the signal levels exceed the normal range and enter clipping.

36. EFFECT RETURN

These stereo faders are used to determine the effect amount added to the main mix. In case you have to set these faders at a position above the +5dB mark, the level of the FX unit’s input signal might be too low. If that is the case, use the AUX/FX SEND controls to increase the input levels.

Use the FX faders to set the final amount of the effects signal that is added to the main mix.

14

Image 14
Contents CMS 1000/1600/2200 Table DES Matières ContentsInhaltsverzeichnis Important Safety Instructions Descriptions Unpacking and WarrantyInstallation and Connections Line Input MonoMIC Gain Setting InstructionsInsert EQ Section LO CUT 80 HzVoicing Filter AUX / FX 1/2 AUX 3/4PAN Signal / Peak IndicatorVolume MuteStereo Input L/MONO R Input Stereo15.MIC Gain MICAUX / FX 1/2 AUX3/4 BAL Line TrimEQ Section SIGNAL/PEAK Changing FX Start Programs Effects 1/2FX1/FX2 27/28. AUX1/2 SendPeak LED Display30. UP/DOWN Effect ReturnAUX3/4 Inserts AUX3&4 / MasterAUX3/4 OUT AUX3/4 PostBand Equalizer AUX3/4 VolumePower Anzeige Standby MasterMaster LED-DISPLAY PFL MasterPhones Level Mono OutputMono OUT Level & PRE/POST Record Send L/RMaster Inserts FootswitchMaster OUT Lamp XLRPower Rear PanelLF-Cables Balanced or Unbalanced? CablingCabling UnbalancedSetting UP a STANDARD-PA System Sound CheckMain Mix Monitor MixSetup Examples Optional Subwoofer MonitoringSetup Examples Setup Examples Wichtige Sicherheitshinweise Beschreibung Auspacken und GarantieLine Gain Klangregelung Einstellhinweis Signal / PEAK- Anzeige Input Stereo +20 +15 +10 100 200 500 10k 20k AUX / FX Effekt 1/2 Umstellung der Effekt-StartprogrammeEinstellhinweise Effekt ReturnAUX3/4 +20 +15 +10 100 200 500 10k Master LED-DISPLAY Mono OUT Level PhonesMaster OUT Rückseite Aufbau Einer STANDARD-PA VerkabelungAufbau SoundcheckHauptmix MonitormixAufbau Beispiele Aufbaubeispiele Aufbaubeispiele Instructions DE Sécurité Importantes Installation et Branchements Déballage et garantieEntrée Mono Line LigneInsert Insertion Conseils de réglageEQ Section Égaliseur LO CUT 80 Hz Filtre coupe-basVoicing Filter Filtre de Voix Instructions de réglage AUX/FX 1/2 Auxiliaires/EffetsIndicateur SIGNAL/PEAK Entrée Stéréo 21.AUX3/4 Section EQAUX/FX 1/2 BAL anceSIGNAL/PEAK Effets 1/2 Changer les effets de démarrageTemoin Peak Afficheur31/32. FX1/2 à AUX3/4 Effect Return Retour D’EFFETAUX3&4 / Master 45. Témoin Power 44. Égaliseur 7 BandesEQ to Affectation de l‘EQ 46. Échelle DE LED MasterMaster L+R Phones Sortie casques Mono OUTNiveau Mono OUT ET PRE/POST Track Return L/R Retour 2 PistesMaster OUT Sortie générale Master Inserts Insertions principalesPanneau Arrière Câbles basse fréquence Symétrisés ou non symétrisés ? CablageCâblage Installation D‘UN Système DE Sonorisation Mixage principal Mixage des retours MonitorExemples D‘INSTALLATION Exemples D‘INSTALLATION Exemples D‘INSTALLATION Specifications Block Diagram Dimensions / Abmessungen Effect presets Effekt Presets Programmes Effets
Related manuals
Manual 32 pages 46.96 Kb