Dynacord 2200, CMS 1000, 1600 owner manual Rear Panel, Power

Page 20

REAR PANEL

POWER

Mains switch to turn the CMS on or off.

The CMS is operational once the POWER LED lights and outputs are activated through automatic switching of the output relays.

Please make sure to set the master faders to their minimum position or engage the STANDBY switch before switching the power on. This will save you, your audience, and the equipment from unnecessary stress from unwanted loud signals or even worse from acoustic feedback.

Please, proceed in the following order when switching your equipment on:

1.power on any external device, like an external equalizer, etc.

2.power on the CMS

3.power on external power amps, like main amp and monitor amp. When switching the power off, please proceed in the opposite order.

20

Image 20
Contents CMS 1000/1600/2200 Table DES Matières ContentsInhaltsverzeichnis Important Safety Instructions Descriptions Unpacking and WarrantyInstallation and Connections Line Input MonoMIC Gain Setting InstructionsInsert EQ Section LO CUT 80 HzVoicing Filter AUX / FX 1/2 AUX 3/4Signal / Peak Indicator VolumePAN MuteInput Stereo 15.MICStereo Input L/MONO R Gain MICAUX / FX 1/2 AUX3/4 BAL Line TrimEQ Section SIGNAL/PEAK Effects 1/2 FX1/FX2Changing FX Start Programs 27/28. AUX1/2 SendDisplay 30. UP/DOWNPeak LED Effect ReturnAUX3&4 / Master AUX3/4 OUTAUX3/4 Inserts AUX3/4 PostBand Equalizer AUX3/4 VolumePower Anzeige Master Master LED-DISPLAYStandby PFL MasterMono Output Mono OUT Level & PRE/POSTPhones Level Record Send L/RFootswitch Master OUTMaster Inserts Lamp XLRPower Rear PanelCabling CablingLF-Cables Balanced or Unbalanced? UnbalancedSetting UP a STANDARD-PA System Sound CheckMain Mix Monitor MixSetup Examples Optional Subwoofer MonitoringSetup Examples Setup Examples Wichtige Sicherheitshinweise Beschreibung Auspacken und GarantieLine Gain Klangregelung Einstellhinweis Signal / PEAK- Anzeige Input Stereo +20 +15 +10 100 200 500 10k 20k AUX / FX Effekt 1/2 Umstellung der Effekt-StartprogrammeEinstellhinweise Effekt ReturnAUX3/4 +20 +15 +10 100 200 500 10k Master LED-DISPLAY Mono OUT Level PhonesMaster OUT Rückseite Aufbau Einer STANDARD-PA VerkabelungAufbau SoundcheckHauptmix MonitormixAufbau Beispiele Aufbaubeispiele Aufbaubeispiele Instructions DE Sécurité Importantes Installation et Branchements Déballage et garantieEntrée Mono Line LigneInsert Insertion Conseils de réglageEQ Section Égaliseur LO CUT 80 Hz Filtre coupe-basVoicing Filter Filtre de Voix Instructions de réglage AUX/FX 1/2 Auxiliaires/EffetsIndicateur SIGNAL/PEAK Entrée Stéréo Section EQ AUX/FX 1/221.AUX3/4 BAL anceSIGNAL/PEAK Effets 1/2 Changer les effets de démarrageAfficheur 31/32. FX1/2 à AUX3/4Temoin Peak Effect Return Retour D’EFFETAUX3&4 / Master 45. Témoin Power 44. Égaliseur 7 BandesEQ to Affectation de l‘EQ 46. Échelle DE LED MasterMaster L+R Mono OUT Niveau Mono OUT ET PRE/POSTPhones Sortie casques Track Return L/R Retour 2 PistesMaster OUT Sortie générale Master Inserts Insertions principalesPanneau Arrière Câbles basse fréquence Symétrisés ou non symétrisés ? CablageCâblage Installation D‘UN Système DE Sonorisation Mixage principal Mixage des retours MonitorExemples D‘INSTALLATION Exemples D‘INSTALLATION Exemples D‘INSTALLATION Specifications Block Diagram Dimensions / Abmessungen Effect presets Effekt Presets Programmes Effets
Related manuals
Manual 32 pages 46.96 Kb