Garland XG24-JIB, XG36-JIB service manual Accessory Kit Electrical Supply Lines

Page 11

UNIT INSTALLATION continued

B.Install the nipple assembly into the elbow (3/4” NPT) Refer to Photo A

C.Install the manifold support bracket over the nipple attaching it to the circular bracket on the nipple. Do not tighten screws. Refer to Photo B

Photo B

D.Adjust the manifold support bracket flush with the rear gas support bracket. Refer to Photo B

E.Tighten the loose screws of the manifold support bracket. Refer to Photo B

F.Lock the two brackets together using two screws. Refer to Photo C

Photo C

Accessory Kit – Electrical Supply Lines:

The accessory kit also contains electric power cord and plug and has a stain relief suited for each unit. Refer to Plug Configuration in SPECIFICATIONS and Photo D

Installation of Cord And Plug With Strain Relief:

1.Remove the left grease bucket support attached by two metal screws and the stainless steel left side body panel attached by five metal screws.

2.Remove the cord & plug and strain relief assembly from the accessory kit. Refer to photo D.

Photo D

3.Remove the locknut from at the end of the cord. Refer to photo E.

Photo E

Part # JIBSM08 Rev.6 (08/04/09)

Page 11

Image 11

Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Plug Configuration SpecificationsIntroduction SafetyWarranty Shipping Damage Claim ProcedureSafety National Codes Requirements Unit InstallationRating Plate Location General InformationElectrical Connections Unit InstallationAccessory Kit Main Gas Inlet Appliances Equipped with CastersAccessory Kit Electrical Supply Lines Changing to a different type of gas Electrical Connection Terminal Block ConnectionGrease Bucket Ventilation and ClearanceIgniter Inspection Burner Air AdjustmentIgniter Adjustment Grill Controls Grill Controls Platen Zeroing Programming Mode System SetupLower Front Left Raise Back Right Platen ZeroingOptional Accessories Release material sheet must be replaced when Release Material InstallationNormal Operation Normal Operation Daily Cleaning Cleaning and MaintenanceCleaning During Operation Cleaning and Maintenance Programming Modes/Menu Sequence ProgrammingProgramming To Change the Cook Time of a Product To Change Upper Platen Set TemperatureTo Change Grill Set Temperature To Change Product Gap SettingTo Change a Product Name To View Recovery Time Upper PlatenTo View Recovery Time Grill To Change Product Button,KeyAssignmentTo View the Software Number To Change temperature Units, F or CTo Change Gap Setting Display Units To View the Flash NumberTo Change Probe Calibration Grill To Change the Alarm VolumeTo Change the Key Chirp To Change Probe Calibration UpperTo Turn Extended Time On/Off To Change Platen SetTo Change Instant-On Time To Change Control TypeTo Change the Grill Function To Change the Start DelayTo Change the Alarm Mode To Turn Clean Mode On/OffTo Change SCK Address To Perform Limit Switch TestTo Modify a Product Name in Library To Calibrate CalibrationBi-Weekly Calibration Probe Locations CalibrationError Messages TroubleshootingLow Internal Product Temperatures Technical TroubleshootingYES Technical TroubleshootingController Displays Too Hot YES Controller displays Probe Error Upper platen is not zeroed properly Inconsistent Or Erratic Internal Product TemperatureProbable diagnosis YES Check voltage of upper limit Does Upper Limit YES Controller Displays Ignition Failure No flame at allNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Contents Parts ListModel XG24-JIB Description Quantity Gas Xpress Grill Complete Exploded View Model XG24-JIBXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen 4517022 Platen Conduit Gas Xpress Grill Platen Assembly View Model XG24-JIBXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Ignition Module Component BracketContactor Bracket Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB Part List Book Released Revision HistoryREV. # Item #Right Zone Parts ListGrill Complete Assembly Description Quantity Critical Gas Xpress Grill Complete Exploded View Model XG36-JIB4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Center Zone Right Zone Left Zone Gas Xpress Grill Gas Tubing Model XG36-JIBItem # Date Revision HistoryDiagram WiringWiring Diagram Time Controller Menu ItemsJack in the Box Menu Items Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09