Garland XG36-JIB, XG24-JIB service manual Platen Zeroing, Programming Mode System Setup

Page 16

PLATEN ZEROING

Turn Master power switch “ON”, wait for controllers to display “OFF”.

Note: Release sheets should not be installed during this procedure.

1.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

2.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

3.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

4.Press two, (2) times in succession to display

“PROGRAMMING MODE SYSTEM SETUP.”

5.Press six, (6) times. “PLATEN SET +/- XX” is displayed. (XX=numbers that will vary from grill to grill.)

6.Allow time for grill to heat and turn ready. Press both the Cancel (Green) and Standby (Black) buttons simultaneously to lower the upper platen. Press the Cancel (Green) button to raise the platen. Now, press both the Cancel (Green) and (Black) Buttons to re-lower the platen.

7.Remove platen adjuster caps from all four adjustment points on each platen. Remove the four locking caps from the adjustment points.

8.Using the adjusting tool lower platen until adjusting tool touches the arm assembly.

9.With gapping tool, adjust right rear of platen until the gapping tool fits snugly between the upper platen and grill surface.

10.Move next to the left front adjuster and raise the platen until the gapping tool fits snugly between the upper platen and grill surface.

11.Next go to the left rear adjuster and raise the platen until the gapping tool fits snugly between the upper platen and grill surface.

12.Move next to the right front adjustment and raise the platen until the gapping tool fits snugly between the upper platen and grill surface.

13.Repeat steps 9-12 one or more times until gapping tool fits snugly between the upper platen and grill surface at all four adjustment points without further adjustment.

(See diagram below.)

14.Replace the platen adjuster locking caps “hollow side down” and tighten snugly. Replace platen adjuster caps.

15.Repeat steps 9-14 for each platen.

Insert gap tool directly below platen adjusters.

Page 16

Part # JIBSM08 Rev 7 (08/04/09)

Image 16

Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Specifications Plug ConfigurationSafety WarrantyShipping Damage Claim Procedure IntroductionSafety Unit Installation Rating Plate LocationGeneral Information National Codes RequirementsUnit Installation Accessory Kit Main Gas InletAppliances Equipped with Casters Electrical ConnectionsAccessory Kit Electrical Supply Lines Electrical Connection Terminal Block Connection Grease BucketVentilation and Clearance Changing to a different type of gasIgniter Adjustment Burner Air AdjustmentIgniter Inspection Grill Controls Grill Controls Programming Mode System Setup Platen ZeroingPlaten Zeroing Lower Front Left Raise Back RightOptional Accessories Release Material Installation Release material sheet must be replaced whenNormal Operation Normal Operation Cleaning During Operation Cleaning and MaintenanceDaily Cleaning Cleaning and Maintenance Programming Programming Modes/Menu SequenceProgramming To Change Upper Platen Set Temperature To Change Grill Set TemperatureTo Change Product Gap Setting To Change the Cook Time of a ProductTo View Recovery Time Upper Platen To View Recovery Time GrillTo Change Product Button,KeyAssignment To Change a Product NameTo Change temperature Units, F or C To Change Gap Setting Display UnitsTo View the Flash Number To View the Software NumberTo Change the Alarm Volume To Change the Key ChirpTo Change Probe Calibration Upper To Change Probe Calibration GrillTo Change Platen Set To Change Instant-On TimeTo Change Control Type To Turn Extended Time On/OffTo Change the Start Delay To Change the Alarm ModeTo Turn Clean Mode On/Off To Change the Grill FunctionTo Modify a Product Name in Library To Perform Limit Switch TestTo Change SCK Address Bi-Weekly Calibration CalibrationTo Calibrate Calibration Probe LocationsTroubleshooting Error MessagesTechnical Troubleshooting Low Internal Product TemperaturesController Displays Too Hot Technical TroubleshootingYES YES Controller displays Probe Error Inconsistent Or Erratic Internal Product Temperature Upper platen is not zeroed properlyProbable diagnosis YES Check voltage of upper limit Does Upper Limit Controller Displays Ignition Failure No flame at all YESNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Parts List ContentsModel XG24-JIB Gas Xpress Grill Complete Exploded View Model XG24-JIB Description QuantityXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen Gas Xpress Grill Platen Assembly View Model XG24-JIB 4517022 Platen ConduitXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Contactor Bracket Component BracketIgnition Module Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB Revision History REV. #Item # Part List Book ReleasedParts List Right ZoneGrill Complete Assembly Gas Xpress Grill Complete Exploded View Model XG36-JIB Description Quantity Critical4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Gas Xpress Grill Gas Tubing Model XG36-JIB Center Zone Right Zone Left ZoneRevision History Item # DateWiring DiagramWiring Diagram Jack in the Box Menu Items Controller Menu ItemsTime Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09