Garland XG24-JIB, XG36-JIB service manual Bi-Weekly Calibration, To Calibrate

Page 33

CALIBRATION

Bi-Weekly Calibration:

Tools: Digital Pyrometer with Surface Probe

Warning: PERSONAL INJURY FROM BURNS MAY RESULT WHEN COMING IN CONTACT WITH HOT COOKING SURFACES..

NOTE: Calibration of grills is done with release material sheets installed..

NOTE: CALIBRATION REQUIREMENTS

The control software will beep to the user when it is appropriate to calibrate.. The control will allow calibration provided the following conditions are met:

•Temperature is currently falling from a detected peak of 360°F or higher..

•Temperature is falling and has fallen 2°F from a detected peak that is within the 350-360°F range.. (i..e.. calibration would be allowed at 355°F if the achieved peak temperature was 357°F)

•Temperature is rising through the 350-360°F range as a result of a heat on pulse of less than 30 seconds..

To Calibrate:

1.The upper platens and lower grill plate should be at operating temperatures to perform this calibration procedure.

Turn on the Master Switch and press to enter cooking mode.

2.Press or to select a “CLAM” operation and allow the grill to reach the set temperature and stabilize, (approximately 30 minutes).

3.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

4.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

5.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

6.Press three, (3) times. “PROGRAMMING MODE SYSTEM SETUP” is displayed.

7.Press five, (5) times. “PROBE CAL – UPPER XXXF” is displayed.

8.Place the surface probe of the digital pyrometer directly on the probe location, (see diagram on following page).

9.Allow at least 5 seconds for the pyrometer to respond and stabilize. Note the temperature on the pyrometer.

10.If the temperature on the grill control display does not match the temperature on the pyrometer, adjust the temperature on the grill control accordingly using the andbuttons.

11.Press. “PROBE CAL – GRILL XXXF” is displayed.

12.Repeat steps 8 - 10.

13.Pressto save the changes.

14.Press to return to “PROGRAMMING MODE SYSTEM SETUP”

15.Pressagain to exit.

16.Repeat steps 1 - 15 at each control.

Part # JIBSM08 Rev.6 (08/04/09)

Page 33

Image 33

Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Plug Configuration SpecificationsWarranty SafetyShipping Damage Claim Procedure IntroductionSafety Rating Plate Location Unit InstallationGeneral Information National Codes RequirementsAccessory Kit Main Gas Inlet Unit InstallationAppliances Equipped with Casters Electrical ConnectionsAccessory Kit Electrical Supply Lines Grease Bucket Electrical Connection Terminal Block ConnectionVentilation and Clearance Changing to a different type of gasBurner Air Adjustment Igniter AdjustmentIgniter Inspection Grill Controls Grill Controls Platen Zeroing Programming Mode System SetupLower Front Left Raise Back Right Platen ZeroingOptional Accessories Release material sheet must be replaced when Release Material InstallationNormal Operation Normal Operation Cleaning and Maintenance Cleaning During OperationDaily Cleaning Cleaning and Maintenance Programming Modes/Menu Sequence ProgrammingProgramming To Change Grill Set Temperature To Change Upper Platen Set TemperatureTo Change Product Gap Setting To Change the Cook Time of a ProductTo View Recovery Time Grill To View Recovery Time Upper PlatenTo Change Product Button,KeyAssignment To Change a Product NameTo Change Gap Setting Display Units To Change temperature Units, F or CTo View the Flash Number To View the Software NumberTo Change the Key Chirp To Change the Alarm VolumeTo Change Probe Calibration Upper To Change Probe Calibration GrillTo Change Instant-On Time To Change Platen SetTo Change Control Type To Turn Extended Time On/OffTo Change the Alarm Mode To Change the Start DelayTo Turn Clean Mode On/Off To Change the Grill FunctionTo Perform Limit Switch Test To Modify a Product Name in LibraryTo Change SCK Address Calibration Bi-Weekly CalibrationTo Calibrate Probe Locations CalibrationError Messages TroubleshootingLow Internal Product Temperatures Technical TroubleshootingTechnical Troubleshooting Controller Displays Too HotYES YES Controller displays Probe Error Upper platen is not zeroed properly Inconsistent Or Erratic Internal Product TemperatureProbable diagnosis YES Check voltage of upper limit Does Upper Limit YES Controller Displays Ignition Failure No flame at allNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Contents Parts ListModel XG24-JIB Description Quantity Gas Xpress Grill Complete Exploded View Model XG24-JIBXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen 4517022 Platen Conduit Gas Xpress Grill Platen Assembly View Model XG24-JIBXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Component Bracket Contactor BracketIgnition Module Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB REV. # Revision HistoryItem # Part List Book ReleasedRight Zone Parts ListGrill Complete Assembly Description Quantity Critical Gas Xpress Grill Complete Exploded View Model XG36-JIB4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Center Zone Right Zone Left Zone Gas Xpress Grill Gas Tubing Model XG36-JIBItem # Date Revision HistoryDiagram WiringWiring Diagram Controller Menu Items Jack in the Box Menu ItemsTime Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09