Garland XG36-JIB, XG24-JIB Electrical Connection Terminal Block Connection, Grease Bucket

Page 12

UNIT INSTALLATION continued

4. Insert loose wires and strain relief cord end through

the hole at the bottom of the unit. Refer to photo F and

secure with locknut. Refer to photo E.

Note: see diagram below for connections to terminal block.

Wire leads from Cord and Plug

Green-Ground

White - Z

Black - Y

Red - X

Main Terminal

Block of Grill

G

Z

Y

X

Photo F

5.Attached wire ends to terminal block as shown in next section and referenced in wiring diagrams at back of this manual.

6.Reinstall the side panel and grease bucket support with metal screws. The external electrical connection should appear as in photo G.

Photo G

Electrical Connection

Terminal Block Connection

All electrically operated appliances must be electrically grounded in accordance with local codes; or in the absence of local codes, with the latest edition of National Wiring Regulations. A wiring diagram is located behind the rear panel of the grill. See rating plate in rear of grill, or lower front panel for proper voltages.

Grease Bucket:

The griddle is supplied with two stainless steel side grease buckets that must be installed before the unit is used. Each bucket slides into position along stainless steel supports.

Ventilation and Clearance:

One of the most important considerations for efficient grill operation is proper ventilation and air supply. Insure the grill is installed so the products of combustion are removed efficiently and the ventilation system does not produce drafts that interfere with proper burner operation.

Proper operation of exhaust fans (speed, rotation and adjustment) is essential. In addition to the exhaust system the make-up air system, (HVAC), for the kitchen is the

air supply for the combustion air for the burners. Proper incoming air is essential for all gas operated equipment. Poor incoming make-up will cause inefficient burner operation, delayed ignition and possible burner failure.

Any ventilation system will break down if improperly maintained. The duct system, the hood, and the filters must be cleaned on a regular basis and kept grease free.

The room containing the grill is required to have a permanent air vent. The minimum effective area of the vent shall be 0.7 in.² per kW. Air vents shall be of such a size to compensate for the effects of any extract fan in the premises.

Changing to a different type of gas

Changing from one gas type to another must only be done by a Qualified Gas Engineer and according to local regulations.

Page 12

Part # JIBSM08 Rev 7 (08/04/09)

Image 12
Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Specifications Plug ConfigurationSafety WarrantyShipping Damage Claim Procedure IntroductionSafety Unit Installation Rating Plate LocationGeneral Information National Codes RequirementsUnit Installation Accessory Kit Main Gas InletAppliances Equipped with Casters Electrical ConnectionsAccessory Kit Electrical Supply Lines Electrical Connection Terminal Block Connection Grease BucketVentilation and Clearance Changing to a different type of gasBurner Air Adjustment Igniter AdjustmentIgniter Inspection Grill Controls Grill Controls Programming Mode System Setup Platen ZeroingPlaten Zeroing Lower Front Left Raise Back RightOptional Accessories Release Material Installation Release material sheet must be replaced whenNormal Operation Normal Operation Cleaning and Maintenance Cleaning During OperationDaily Cleaning Cleaning and Maintenance Programming Programming Modes/Menu SequenceProgramming To Change Upper Platen Set Temperature To Change Grill Set TemperatureTo Change Product Gap Setting To Change the Cook Time of a ProductTo View Recovery Time Upper Platen To View Recovery Time GrillTo Change Product Button,KeyAssignment To Change a Product NameTo Change temperature Units, F or C To Change Gap Setting Display UnitsTo View the Flash Number To View the Software NumberTo Change the Alarm Volume To Change the Key ChirpTo Change Probe Calibration Upper To Change Probe Calibration GrillTo Change Platen Set To Change Instant-On TimeTo Change Control Type To Turn Extended Time On/OffTo Change the Start Delay To Change the Alarm ModeTo Turn Clean Mode On/Off To Change the Grill FunctionTo Perform Limit Switch Test To Modify a Product Name in LibraryTo Change SCK Address Calibration Bi-Weekly CalibrationTo Calibrate Calibration Probe LocationsTroubleshooting Error MessagesTechnical Troubleshooting Low Internal Product TemperaturesTechnical Troubleshooting Controller Displays Too HotYES YES Controller displays Probe Error Inconsistent Or Erratic Internal Product Temperature Upper platen is not zeroed properlyProbable diagnosis YES Check voltage of upper limit Does Upper Limit Controller Displays Ignition Failure No flame at all YESNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Parts List ContentsModel XG24-JIB Gas Xpress Grill Complete Exploded View Model XG24-JIB Description QuantityXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen Gas Xpress Grill Platen Assembly View Model XG24-JIB 4517022 Platen ConduitXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Component Bracket Contactor BracketIgnition Module Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB Revision History REV. #Item # Part List Book ReleasedParts List Right ZoneGrill Complete Assembly Gas Xpress Grill Complete Exploded View Model XG36-JIB Description Quantity Critical4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Gas Xpress Grill Gas Tubing Model XG36-JIB Center Zone Right Zone Left ZoneRevision History Item # DateWiring DiagramWiring Diagram Controller Menu Items Jack in the Box Menu ItemsTime Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09