Garland XG24-JIB, XG36-JIB service manual Normal Operation

Page 21

NORMAL OPERATION continued

4To cancel a cook cycle at anytime the press the green

CANCEL/RAISE PLATEN BUTTON .

5.During a cook cycle, the display shows the product recipe name in the first line and the remaining cook time count down in the second line.

6.The display shows the “SEAR” or “FLIP” alarm message with flashing in the second line if the current cooking product is flat recipe and the sear time or flip time is not zero.

7.A cook alarm sounds with a repeating beep pattern. Pressing the black RAISE button acknowledges the “SEAR” or “FLIP” alarm message if the alarm field in system setup is set to MANUAL.

8.The “SEAR” or “FLIP” alarm message stops after 5 seconds if the alarm field in system setup is set to AUTO.

9.When a cook is complete, the display shows the product recipe name in the first line and a flashing “REMOVE” message in the second line. A repeating beeping alarm also sounds.

10.Pressing the black RAISE button cancels the cook done alarm.

11.The unit reverts back to IDLE mode.

Enter Standby Mode:

Stand by mode is used during slow periods to conserve energy with out a complete shut down of the unit. When cooking temperatures are again required, pre-heat cook temperature/time is reduced. Stand by mode temperatures can be adjusted, see the PROGRAMING section.

1.Select Standby Mode by pressing or until “STANDBY” is displayed.

2.Press the GREEN (‘CANCEL/RAISE’) and the BLACK buttons at the same time. As soon as the upper platen moves down, the display will read “STANDBY MODE.” (Note:

The first time Standby Mode is entered, the display will prompt the operator to press ENTER after pressing the GREEN and BLACK buttons.)

Exit Standby Mode:

1.Press the GREEN (‘CANCEL/RAISE’) button. The upper platen will raise and the display will read “CANCEL” with an audible alarm.

To Display the Current Temperatures:

1.Press the button and repeat for each zone to be displayed...

1st press - LOWER GRILL ZONE 2nd press - UPPER PLATEN

NOTE: The temperatures may be displayed at any time, including during a cooking cycle.

To View Settings for a Menu Item:

1.Enter Programming; Menu Items, (see Programming)

2.Pressto enter “PROGRAMMING MODE MENU ITEMS”

3.Useandto choose the desired Menu Item.

4.Pressto scroll through settings for the chosen item.

To Clean the Grill:

1.To start a CLEAN MODE select the clean mode recipe by pressing product key 10 or by using the UP/DOWN keys

orto select the clean mode recipe.

2.The controller regulates the platen and grill temperatures to the set temperatures of the clean mode recipe. The display shows the message “CLEAN MODE” in the first line and the actual grill temperature in the second line.

3.Press the ENTER keyto initiate the clean mode.

4.The display SHOWS the message “READY TO CLEAN” with flashing in the second line when the actual temperature is reached (or greater than the set temperatures of clean mode recipe (default 250 F for both the platen and grill)). A 5 second repeating beep pattern is sounded.

5.Press the ENTER key again, the heater’s control for the platen and grill are turned off and the display shows the message “CLEANING” with flashing in the second line.

6.Press the ENTER key again to exit the CLEAN MODE. The display shows the message “STANDBY” in the first line. The control transitions to “STANDBY MODE” and preheats to idle condition.

PLATEN SET:

This function allows the platen to be moved up or down once it is parallel to the grill surface. Values range from –160 to +160.

Part # JIBSM08 Rev.6 (08/04/09)

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Plug Configuration SpecificationsWarranty SafetyShipping Damage Claim Procedure IntroductionSafety Rating Plate Location Unit InstallationGeneral Information National Codes RequirementsAccessory Kit Main Gas Inlet Unit InstallationAppliances Equipped with Casters Electrical ConnectionsAccessory Kit Electrical Supply Lines Grease Bucket Electrical Connection Terminal Block ConnectionVentilation and Clearance Changing to a different type of gasBurner Air Adjustment Igniter AdjustmentIgniter Inspection Grill Controls Grill Controls Platen Zeroing Programming Mode System SetupLower Front Left Raise Back Right Platen ZeroingOptional Accessories Release material sheet must be replaced when Release Material InstallationNormal Operation Normal Operation Cleaning and Maintenance Cleaning During OperationDaily Cleaning Cleaning and Maintenance Programming Modes/Menu Sequence ProgrammingProgramming To Change Grill Set Temperature To Change Upper Platen Set TemperatureTo Change Product Gap Setting To Change the Cook Time of a ProductTo View Recovery Time Grill To View Recovery Time Upper PlatenTo Change Product Button,KeyAssignment To Change a Product NameTo Change Gap Setting Display Units To Change temperature Units, F or CTo View the Flash Number To View the Software NumberTo Change the Key Chirp To Change the Alarm VolumeTo Change Probe Calibration Upper To Change Probe Calibration GrillTo Change Instant-On Time To Change Platen SetTo Change Control Type To Turn Extended Time On/OffTo Change the Alarm Mode To Change the Start DelayTo Turn Clean Mode On/Off To Change the Grill FunctionTo Perform Limit Switch Test To Modify a Product Name in LibraryTo Change SCK Address Calibration Bi-Weekly CalibrationTo Calibrate Probe Locations CalibrationError Messages TroubleshootingLow Internal Product Temperatures Technical TroubleshootingTechnical Troubleshooting Controller Displays Too HotYES YES Controller displays Probe Error Upper platen is not zeroed properly Inconsistent Or Erratic Internal Product TemperatureProbable diagnosis YES Check voltage of upper limit Does Upper Limit YES Controller Displays Ignition Failure No flame at allNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Contents Parts ListModel XG24-JIB Description Quantity Gas Xpress Grill Complete Exploded View Model XG24-JIBXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen 4517022 Platen Conduit Gas Xpress Grill Platen Assembly View Model XG24-JIBXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Component Bracket Contactor BracketIgnition Module Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB REV. # Revision HistoryItem # Part List Book ReleasedRight Zone Parts ListGrill Complete Assembly Description Quantity Critical Gas Xpress Grill Complete Exploded View Model XG36-JIB4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Center Zone Right Zone Left Zone Gas Xpress Grill Gas Tubing Model XG36-JIBItem # Date Revision HistoryDiagram WiringWiring Diagram Controller Menu Items Jack in the Box Menu ItemsTime Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09
Top Page Image Contents