Garland XG36-JIB To Change Platen Set, To Change Instant-On Time, To Change Control Type

Page 30

PROGRAMMING continued

Temperature is currently falling from a detected peak of 360°F or higher..

Temperature is falling and has fallen 2°F from a detected peak that is within the 350-360°F range.. (i..e.. calibration would be allowed at 355°F if the achieved peak temperature was 357°F)

Temperature is rising through the 350-360°F range as a result of a heat on pulse of less than 30 seconds..

To Change Platen Set:

1.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

2.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

3.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

4.Press two, (2) times. “PROGRAMMING MODE SYSTEM SETUP” is displayed.

5.Press seven, (7) times. “PLATEN SET +/- XX” is displayed. (numbers will vary by grill)

6.Use and to change the Platen Set to the correct value.

7.Pressto save the changes.

8.Press to return to “PROGRAMMING MODE MENU ITEMS”

9.Pressagain to exit.

To Change Instant-On Time:

1.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

2.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

3.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

4.Press two, (2) times. “PROGRAMMING MODE SYSTEM SETUP” is displayed.

5.Press eight, (8) times. “INSTANT ON TIME XX:XX” is displayed. (numbers will vary by grill).

6.Use and to change the Instant on Time to the desired value.

7.Pressto save the changes.

8.Press to return to “PROGRAMMING MODE MENU ITEMS”

9. Pressagain to exit.

To Change Control Type:

Note: this must be verified if the control is changed, match the new control to the grill.

1.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

2.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

3.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

4.Press two, (2) times. “PROGRAMMING MODE SYSTEM SETUP” is displayed.

5.Press nine, (9) times. “CONTROL TYPE ELECTRIC (or GAS)” is displayed. (type varies by grill).

6.Use and to change Control Type to match the design of the grill.

7.Pressto save the changes.

8.Press to return to “PROGRAMMING MODE MENU ITEMS”

9.Pressagain to exit.

To Turn Extended Time On/Off:

1.Press and hold for three, (3) seconds. “ENTER CODE” is displayed.

2.Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ” is displayed.

3.Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed.

4.Press two, (2) times. “PROGRAMMING MODE SYSTEM SETUP” is displayed.

5.Press ten, (10) times. “EXTENDED TIME NO (or YES)” is displayed.

6.Useandto turn Extended Time on or off.

7.Pressto save the changes.

8.Press to return to “PROGRAMMING MODE MENU ITEMS”

9.Pressagain to exit.

Page 30

Part # JIBSM08 Rev 7 (08/04/09)

Image 30
Contents Jack in the BOX GAS Xpress GRILLS, Models XG24-JIB, XG36-JIB Table of Contents Table of Contents Dimensions and SPECIFICATIONS, XG24-JIB Model Dimensions and SPECIFICATIONS, XG36-JIB Model Specifications Plug ConfigurationShipping Damage Claim Procedure SafetyWarranty IntroductionSafety General Information Unit InstallationRating Plate Location National Codes RequirementsAppliances Equipped with Casters Unit InstallationAccessory Kit Main Gas Inlet Electrical ConnectionsAccessory Kit Electrical Supply Lines Ventilation and Clearance Electrical Connection Terminal Block ConnectionGrease Bucket Changing to a different type of gasBurner Air Adjustment Igniter AdjustmentIgniter Inspection Grill Controls Grill Controls Programming Mode System Setup Platen ZeroingPlaten Zeroing Lower Front Left Raise Back RightOptional Accessories Release Material Installation Release material sheet must be replaced whenNormal Operation Normal Operation Cleaning and Maintenance Cleaning During OperationDaily Cleaning Cleaning and Maintenance Programming Programming Modes/Menu SequenceProgramming To Change Product Gap Setting To Change Upper Platen Set TemperatureTo Change Grill Set Temperature To Change the Cook Time of a ProductTo Change Product Button,KeyAssignment To View Recovery Time Upper PlatenTo View Recovery Time Grill To Change a Product NameTo View the Flash Number To Change temperature Units, F or CTo Change Gap Setting Display Units To View the Software NumberTo Change Probe Calibration Upper To Change the Alarm VolumeTo Change the Key Chirp To Change Probe Calibration GrillTo Change Control Type To Change Platen SetTo Change Instant-On Time To Turn Extended Time On/OffTo Turn Clean Mode On/Off To Change the Start DelayTo Change the Alarm Mode To Change the Grill FunctionTo Perform Limit Switch Test To Modify a Product Name in LibraryTo Change SCK Address Calibration Bi-Weekly CalibrationTo Calibrate Calibration Probe LocationsTroubleshooting Error MessagesTechnical Troubleshooting Low Internal Product TemperaturesTechnical Troubleshooting Controller Displays Too HotYES YES Controller displays Probe Error Inconsistent Or Erratic Internal Product Temperature Upper platen is not zeroed properlyProbable diagnosis YES Check voltage of upper limit Does Upper Limit Controller Displays Ignition Failure No flame at all YESNoyes Linear Actuator Replacement Linear Actuator Replacement JIBSM08 Rev 7 08/04/09 Parts List ContentsModel XG24-JIB Gas Xpress Grill Complete Exploded View Model XG24-JIB Description QuantityXpress Grill Actuator Gas Xpress Grill Actuator Assembly View Model XG24-JIB Xpress Grill Platen Gas Xpress Grill Platen Assembly View Model XG24-JIB 4517022 Platen ConduitXpress Grill Burner Gas Xpress Grill Burner Assembly View Model XG24-JIB Assembly View Model XG24-JIB Component Bracket Contactor BracketIgnition Module Xpress Grill Heat Sink Assembly View Model XG24-JIB Gas Xpress Grill Heat Sink Assembly View Model XG24-JIB Item # Revision HistoryREV. # Part List Book ReleasedParts List Right ZoneGrill Complete Assembly Gas Xpress Grill Complete Exploded View Model XG36-JIB Description Quantity Critical4520578 Grill Plate Thermocouple JIBSM08 Rev.6 08/04/09 Actuator Assembly GAS Xpress Grill Actuator Assembly View Model XG36-JIB Platen Assembly Gas Xpress Grill Platen Assembly View Model XG36-JIB Assembly View Model XG35-JIB Gas Xpress Grill Burner Assembly View Model XG36-JIB Xpress Grill Bracket Component Mounting Bracket Xpress Grill Heat Sink Assembly View Model XG36-JIB Gas Xpress Grill Heat Sink Assembly View Model XG36-JIB Description & Location Quantity Critical Gas Xpress Grill Accessories And Tools Model XG36-JIB Gas Xpress Grill Gas Tubing Model XG36-JIB Center Zone Right Zone Left ZoneRevision History Item # DateWiring DiagramWiring Diagram Controller Menu Items Jack in the Box Menu ItemsTime Temperature Conversion F / C Page JIBSM08 Rev.6 08/04/09