Emerson ib-106-340cdr, oxymitterdr hazardous area in-siu oxygen probe Cell Replacement Kit

Page 56

Instruction Manual

IB-106-340CDR Original Issue January, 2002

Hazardous Area Oxymitter DR

ANSI

GASKET

WIRE AND

PAD ASSEMBLY

ANTI-SEIZE

COMPOUND

PROBE TUBE

(NOT INCLUDED

IN KIT)22 GA.

WIRE

	CORRUGATED
	SEAL	CLOSED END
	CELL AND	CONNECTOR
	CELL AND
	FLANGE	SET SCREWS
	ASSEMBLY	SET SCREWS
	ASSEMBLY
	SOCKET HEAD	TEFLON
	SOCKET HEAD	TUBING
	CAP SCREWS

CALIBRATION GAS

PASSAGE

35830009

Figure 7-1. Cell Replacement Kit

HEX KEYS

SPANNER

WRENCH

ANTI-SEIZE

COMPOUND

PHILIPS

SCREWDRIVER

WRENCH

TUBE INSERTION

TUBE

35830010

Figure 7-2. Probe Disassembly Kit

7-2 Replacement Parts

Rosemount Analytical Inc. A Division of Emerson Process Management

Image 56

Contents Oxymitter DR Essential Instructions Table of Contents Hazardous Area Oxymitter DRList of Illustrations List of TablesPreface DefinitionsHazardous Area Oxymitter DR Section I. Identification Section II. Physical Data Section V. Health Hazard Data Section VI. Reactivity Data Section VII. Spill or Leak Procedures Section IX. Special Precautions Hazardous Area Oxymitter DR Technical Support Hotline System Overview Section Description and SpecificationsComponent Checklist of Typical System Package Contents System Configuration System FeaturesTypical System Installation Abrasive Shield Assembly Flame Arrestor Ceramic Diffusion AssemblyFlame Arrestor Snubber Diffusion Assembly Upgrading the Hazardous Area Oxymitter DRView a View B Specifications Product Matrix Code Sensing Probe TypeCalibration Components Part Number DescriptionSection Installation Mechanical InstallationInstallation Selecting LocationHazardous Area Oxymitter DR Installation Hazardous Area Oxymitter DR with Abrasive Shield Mounting Plate Outline With Abrasive Shield Without Abrasive ShieldOrienting the Optional Vee Deflector Electrical Installation Connect O2 and Heater Thermocouple Signals Pneumatic InstallationSystem Setup OverviewSetup 132 Analog ElectronicsWestinghouse Model 218A ELEC- Tronics Setup G02 G04Westinghouse Model TC200 VERI- Trim Electronics Setup 11. Main PCB Model TC200 Eprom Replacement Westinghouse Model 132 Digital Electronics Setup 12. Main PCB Model 132 Eprom ReplacementWorld Class 3000 Intelligent Field Transmitter Setup 14. Heater Power Supply HPS 3000 Jumper ConfigurationYokogawa ZA8C and AV8C Converter Electronics Setup 15. DR Probe Wired to the ZA8C or a V8C ConverterSection Startup and Operation GeneralHazardous Area Oxymitter DR Section Maintenance and Service Hazardous Area Oxymitter DR ReplacementOverview CalibrationHazardous Area Oxymitter DR Exploded View Install Terminal Block ReplacementEntire Probe Replacement Heater Strut ReplacementHeater Strut Assembly Cell Replacement22220028 This refers to the ceramic diffusion element only General Ceramic Diffusion Element ReplacementReplacement Procedure Ceramic Diffusion Element Replacement Also, do not get any cement onto the flame arrestor elementTermination Housing Wiring Termination Housing ConnectionsHazardous Area Oxymitter DR Symptom Check Fault Remedy Section TroubleshootingProbe Troubleshooting Hazardous Area Oxymitter DR Section Return of Material Equipment ReturnHazardous Area Oxymitter DR Section Replacement Parts Replacement Parts for ProbeCell Replacement Kit O2 Calibration GAS Sequencer Section Optional AccessoriesBY-PASS Packages Hazardous Area Oxymitter DR Section Appendices Appendix A. Updating DR Oxymitter to Full OxymitterHazardous Area Oxymitter DR Upgrade Procedure Figure A-1. Component ReplacementFigure A-2. Terminal Block and Wiring Section Index Hazardous Area Oxymitter DR Warranty Hazardous Area Oxymitter DR Serial no Order no