Emerson ib-106-340cdr instruction manual Hazardous Area Oxymitter DR Serial no Order no

Page 66

Instruction Manual

IB-106-340CDR Original Issue January, 2002

Hazardous Area Oxymitter DR

Hazardous Area Oxymitter DR

Part no.

Serial no.

Order no.

Emerson Process Management
Rosemount Analytical Inc.	Fisher-Rosemount GmbH & Co.
Process Analytic Division	Industriestrasse 1
1201 N. Main St.	63594 Hasselroth
Orrville, OH 44667-0901	Germany
T (330) 682-9010	T 49-6055-884 0
F (330) 684-4434	F 49-6055-884209
E gas.csc@emersonprocess.com

ASIA - PACIFIC	EUROPE, MIDDLE EAST, AFRICA	LATIN AMERICA
Fisher-Rosemount	Fisher-Rosemount Ltd.	Fisher - Rosemount
Singapore Private Ltd.	Heath Place	Av. das Americas
1 Pandan Crescent	Bognor Regis	3333 sala 1004
Singapore 128461	West Sussex PO22 9SH	Rio de Janeiro, RJ
Republic of Singapore	England	Brazil 22631-003
T 65-777-8211	T 44-1243-863121	T 55-21-2431-1882
F 65-777-0947	F 44-1243-845354
http://www.processanalytic.com

© Rosemount Analytical Inc. 2002

Image 66

Contents Oxymitter DR Essential Instructions Table of Contents Hazardous Area Oxymitter DRList of Illustrations List of TablesPreface DefinitionsHazardous Area Oxymitter DR Section I. Identification Section II. Physical Data Section V. Health Hazard Data Section VI. Reactivity Data Section VII. Spill or Leak Procedures Section IX. Special Precautions Hazardous Area Oxymitter DR Technical Support Hotline Section Description and Specifications Component Checklist of Typical System Package ContentsSystem Overview System Configuration System FeaturesTypical System Installation Flame Arrestor Snubber Diffusion Assembly Abrasive Shield AssemblyFlame Arrestor Ceramic Diffusion Assembly Upgrading the Hazardous Area Oxymitter DRView a View B Specifications Product Matrix Code Sensing Probe TypeCalibration Components Part Number DescriptionInstallation Section InstallationMechanical Installation Selecting LocationHazardous Area Oxymitter DR Installation Hazardous Area Oxymitter DR with Abrasive Shield Mounting Plate Outline With Abrasive Shield Without Abrasive ShieldOrienting the Optional Vee Deflector Electrical Installation Connect O2 and Heater Thermocouple Signals Pneumatic InstallationSystem Setup OverviewSetup 132 Analog ElectronicsWestinghouse Model 218A ELEC- Tronics Setup G02 G04Westinghouse Model TC200 VERI- Trim Electronics Setup 11. Main PCB Model TC200 Eprom Replacement Westinghouse Model 132 Digital Electronics Setup 12. Main PCB Model 132 Eprom ReplacementWorld Class 3000 Intelligent Field Transmitter Setup 14. Heater Power Supply HPS 3000 Jumper ConfigurationYokogawa ZA8C and AV8C Converter Electronics Setup 15. DR Probe Wired to the ZA8C or a V8C ConverterSection Startup and Operation GeneralHazardous Area Oxymitter DR Overview Section Maintenance and ServiceHazardous Area Oxymitter DR Replacement CalibrationHazardous Area Oxymitter DR Exploded View Install Terminal Block ReplacementEntire Probe Replacement Heater Strut ReplacementHeater Strut Assembly Cell Replacement22220028 Ceramic Diffusion Element Replacement Replacement ProcedureThis refers to the ceramic diffusion element only General Ceramic Diffusion Element Replacement Also, do not get any cement onto the flame arrestor elementTermination Housing Wiring Termination Housing ConnectionsHazardous Area Oxymitter DR Section Troubleshooting Probe TroubleshootingSymptom Check Fault Remedy Hazardous Area Oxymitter DR Section Return of Material Equipment ReturnHazardous Area Oxymitter DR Section Replacement Parts Replacement Parts for ProbeCell Replacement Kit Section Optional Accessories BY-PASS PackagesO2 Calibration GAS Sequencer Hazardous Area Oxymitter DR Section Appendices Appendix A. Updating DR Oxymitter to Full OxymitterHazardous Area Oxymitter DR Upgrade Procedure Figure A-1. Component ReplacementFigure A-2. Terminal Block and Wiring Section Index Hazardous Area Oxymitter DR Warranty Hazardous Area Oxymitter DR Serial no Order no