Emerson oxymitterdr hazardous area in-siu oxygen probe, ib-106-340cdr Section I. Identification

Page 7

Hazardous Area Oxymitter DR

Instruction Manual

IB-106-340CDR Original Issue January, 2002

CERAMIC FIBER PRODUCTS

MATERIAL SAFETY DATA SHEET

JULY 1, 1996

SECTION I. IDENTIFICATION

PRODUCT NAME

Ceramic Fiber Heaters, Molded Insulation Modules and Ceramic Fiber Radiant Heater Panels.

CHEMICAL FAMILY

Vitreous Aluminosilicate Fibers with Silicon Dioxide.

CHEMICAL NAME

N.A.

CHEMICAL FORMULA

N.A.

MANUFACTURER’S NAME AND ADDRESS

Watlow Columbia	573-474-9402
2101 Pennsylvania Drive	573-814-1300, ext. 5170
Columbia, MO 65202

HEALTH HAZARD SUMMARY

WARNING

•Possible cancer hazard based on tests with laboratory animals.

•May be irritating to skin, eyes and respiratory tract.

•May be harmful if inhaled.

•Cristobalite (crystalline silica) formed at high temperatures (above 1800ºF) can cause severe respiratory disease.

Rosemount Analytical Inc. A Division of Emerson Process Management

P-3

Image 7

Contents Oxymitter DR Essential Instructions Hazardous Area Oxymitter DR Table of ContentsList of Tables List of IllustrationsDefinitions PrefaceHazardous Area Oxymitter DR Section I. Identification Section II. Physical Data Section V. Health Hazard Data Section VI. Reactivity Data Section VII. Spill or Leak Procedures Section IX. Special Precautions Hazardous Area Oxymitter DR Technical Support Hotline Component Checklist of Typical System Package Contents Section Description and SpecificationsSystem Overview System Features System ConfigurationTypical System Installation Upgrading the Hazardous Area Oxymitter DR Abrasive Shield AssemblyFlame Arrestor Ceramic Diffusion Assembly Flame Arrestor Snubber Diffusion AssemblyView a View B Specifications Code Sensing Probe Type Product MatrixPart Number Description Calibration ComponentsSelecting Location Section InstallationMechanical Installation InstallationHazardous Area Oxymitter DR Installation Hazardous Area Oxymitter DR with Abrasive Shield Mounting Plate Outline Without Abrasive Shield With Abrasive ShieldOrienting the Optional Vee Deflector Electrical Installation Pneumatic Installation Connect O2 and Heater Thermocouple SignalsOverview System Setup132 Analog Electronics SetupG02 G04 Westinghouse Model 218A ELEC- Tronics SetupWestinghouse Model TC200 VERI- Trim Electronics Setup 11. Main PCB Model TC200 Eprom Replacement 12. Main PCB Model 132 Eprom Replacement Westinghouse Model 132 Digital Electronics Setup14. Heater Power Supply HPS 3000 Jumper Configuration World Class 3000 Intelligent Field Transmitter Setup15. DR Probe Wired to the ZA8C or a V8C Converter Yokogawa ZA8C and AV8C Converter Electronics SetupGeneral Section Startup and OperationHazardous Area Oxymitter DR Calibration Section Maintenance and ServiceHazardous Area Oxymitter DR Replacement OverviewHazardous Area Oxymitter DR Exploded View Terminal Block Replacement InstallHeater Strut Replacement Entire Probe ReplacementCell Replacement Heater Strut Assembly22220028 Replacement Procedure Ceramic Diffusion Element ReplacementThis refers to the ceramic diffusion element only General Also, do not get any cement onto the flame arrestor element Ceramic Diffusion Element ReplacementTermination Housing Connections Termination Housing WiringHazardous Area Oxymitter DR Probe Troubleshooting Section TroubleshootingSymptom Check Fault Remedy Hazardous Area Oxymitter DR Equipment Return Section Return of MaterialHazardous Area Oxymitter DR Replacement Parts for Probe Section Replacement PartsCell Replacement Kit BY-PASS Packages Section Optional AccessoriesO2 Calibration GAS Sequencer Hazardous Area Oxymitter DR Appendix A. Updating DR Oxymitter to Full Oxymitter Section AppendicesHazardous Area Oxymitter DR Figure A-1. Component Replacement Upgrade ProcedureFigure A-2. Terminal Block and Wiring Section Index Hazardous Area Oxymitter DR Warranty Hazardous Area Oxymitter DR Serial no Order no