Denon CDR-W1500 operating instructions Connections, Restrictions Related to the CD-R/RW Standards

Page 7

Precautions When Loading Discs

Only load one disc. Loading two or more discs in a layer will cause breakdown and may also scratch the discs.

Discs of the 8 cm size should be carefully aligned with the recessed disc guide area and loaded without the use of an adapter. If not properly loaded, the disc may fall out or the disc holder may cease to open.

Be careful not to get your finger caught when the disc holder is closing.

Do not place anything other than a disc on the disc tray.

Do not use discs that are cracked, misshapen, or have been repaired with an adhesive, etc.

Do not use discs that have adhesive coming out from cellophane tape or the label of a rental disc, or adhesive remaining after removal of the label. Use of a disc in this condition may result in the disc not being ejected or in breakdown.

6CONNECTIONS

(1)Analog Input/Output Jack Connections

Use the supplied pin plug cable when making connections with the analog input/output jacks.

q Input:

Amplifier

Connect the analog input jacks (ANALOG

 

 

 

 

 

 

 

IN) of this unit with the output jacks of

SIGNAL

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

SPEAKER SYSTEMS

the amplifier (MD or TAPE).

 

 

 

 

 

R

L

INPUTS

 

PB

 

REC

A

PHONO CD TUNER

AUX

TAPE-1 TAPE-2

TAPE-1 TAPE-2

w Output:

 

 

/MD

/DAT

/MD

/DAT

 

L

 

 

 

 

L

 

 

 

 

 

 

 

B

Connect the analog output jacks

 

 

 

 

 

 

R

 

 

 

 

R

 

 

 

 

 

 

 

 

ENGLISH

Power Supply outlet

120V

60Hz

5RESTRICTIONS RELATED TO THE CD-R/RW STANDARDS

Standards concerned with CD recorder playback have been established based on the existing standards of CD players; however, for recording, the method differs from that used with existing cassette decks and MD recorders, etc. In view of this, please gain a good understanding of the following restrictions associated with CD-R/RW discs and enjoy the medium.

Restrictions of Audio CD-R/RW Discs

Only audio CD-R/RW discs can be recorded with this unit. “Use Audio CD” will be displayed when a disc other than one

 

for use with audio such as a CD-R/RW disc for use with a personal computer or another type of disc is loaded. (See “Discs that

 

Can Be Used with this Unit” on Page 5.)

CD-R discs can be recorded to only once. The recorded information cannot be erased.

(ANALOG OUT) of this unit with the

q

 

 

 

input jacks of the amplifier (MD or TAPE).

 

 

e

e CD-only output:

 

 

 

Only the CD side sound is output.

 

 

 

CDR-W1500

 

 

 

 

Connect to the amplifier’s input jacks

 

 

 

 

(CD, etc.).

ANALOG

 

 

 

CD/

CD

 

 

CDR CDR

 

 

In the dual mode, only the sound of

IN OUT

OUTDIGITAL IN

DIGITAL OUT

 

L

CD/CD-R

CD

 

 

 

 

the CD-R side is output from the

 

R

 

 

 

COAXIAL OPTICAL

COAXIAL OPTICAL

COAXIAL OPTICAL

CD/CD-R output jacks, so this

 

 

 

 

connection is required.

 

w

 

 

Power Supply outlet

120V

60Hz

The recorded information of CD-RW discs can be erased. When this disc has been finalized, erase after the finalization removal

 

operation has been performed. (See “Cancellation of CD-RW disc finalizing” on Page 28.)

Recording mistakes made with CD-R discs cannot be erased; therefore, it is recommended that a CD-RW disc be used until you

 

are accustomed to the recording operation.

Restrictions in Recording with this Unit

The recording operation procedure is the same for CD-R discs and CD-RW discs.

When making additional recording to a previously recorded disc, the end of the last track is detected and recording is started from there.

The record standby mode cannot be set for CD-R/RW discs with a recordable time of about 8 seconds or less remaining. “Disc Full” will be displayed at this time.

A maximum of 99 tracks can be recorded to one CD-R/RW disc. When the recording reaches the 99th track, “Disc Full” is displayed and recordings beyond this track will not be possible.

Digital recording is not possible from CD-R/RW discs onto which have been digitally recorded, normal is it possible from MD or DAT, etc. When a digital recording is attempted from such sources, “Copy Prohibit” is displayed. To record from these digital sources, make the recording from the analog input. (See “Digital Copies” on Page 6.)

This unit cannot record CD-ROM and other non-audio signal sources. When an attempt is made to record from such sources, “Copy Prohibit” is displayed.

When a recording is made from a disc that includes data other than audio signals such as CD graphics or CD-TEXT, only the audio signal is recorded; other data is not recorded.

DVD (Dolby Digital, DTS, and other compressed audio signals) cannot be recorded.

Compatibility with Other CD Players and Discs

Finalization processing on a CD-R disc that has been recorded with this unit will permit that disc to be played on ordinary CD player. (See “Finalizing CD-R/RW Disc” on Page 27.)

Finalization processing on a CD-RW disc that has been recorded with this unit will permit that disc to be played only on a CD player designed to be used with CD-RW discs or on another CD recorder. (See “Finalization Processing of CD-RW Discs” on Page 6.)

NOTES:

To assure accurate recording, record with an ambient temperature of 30 °C or less.

Do not obstruct the ventilation holes on the top.

Recording may stop if the unit is subject to shocks during recording. If recording stops, it may no longer be possible to use the disc normally.

(2)Connection of Digital Input/Output Jacks

Please use optical fiber cables, which is

available on the market, when making

MD recorder

 

 

 

 

 

connections to the digital (OPTICAL)

 

 

 

 

 

 

 

 

input/output jacks.

 

 

 

 

 

 

ANALOG

 

Use 75/ohms pin plug cable, which is

 

 

 

DIGITAL

 

 

OUT IN

 

 

 

OUT

IN

IN

IN

L

 

available on the market, when making

 

 

 

 

 

 

 

 

 

OPTICAL

COAXIAL

OPTICAL-1 OPTICAL-2

R

 

connections to the digital (COAXIAL)

 

 

 

 

 

 

 

 

input/output jacks.

q

 

 

 

 

 

 

 

q Input:

 

 

 

 

 

 

Power Supply outlet

Connections with Playback Equipment

 

 

 

 

 

 

CDR-W1500

 

such as the CD Players

 

 

 

 

 

 

 

 

 

 

 

 

 

 

120 V

The digital input jacks of this unit (either

 

 

 

 

 

 

 

DIGITAL IN OPTICAL or DIGITAL IN

CD/

 

 

 

 

 

e

60 Hz

ANALOG

 

 

 

 

 

 

CDR CDR

CD

DIGITAL IN

 

DIGITAL OUT

 

COAXIAL) should be connected with the

IN OUT

OUT

 

 

 

 

L

CD/CD-R

CD

 

 

digital output jacks of the CD player

 

 

R

 

 

 

 

 

 

 

COAXIAL OPTICAL

COAXIAL

OPTICAL

COAXIAL OPTICAL

 

 

(OPTICAL or COAXIAL).

 

 

 

 

 

 

 

 

w Output:

 

 

 

 

Connections with Equipment having a

 

 

w

 

Digital Input such as the MD Recorder

 

 

CD player

 

 

 

The digital output jacks of this unit (either

 

 

 

 

DIGITAL OUT OPTICAL or DIGITAL OUT

 

 

 

 

COAXIAL) should be connected with the

 

 

 

 

digital input jacks of the MD recorder or

LINE OUT

DIGITAL

 

 

 

OUT OUT

 

other equipment (OPTICAL or COAXIAL).

R

L

COAXIAL OPTICAL

 

e CD-only output:

 

 

 

 

Only the CD side sound is output.

Connect to the digital input jacks of an

MD recorder, etc.

NOTES:

Do not plug the power plug into the power outlet until all connections have been completed.

Connect the red plug of the pin plug cable into the R (right) jack and the white plug into the L (left) jack.

Do not make a connection to the PHONO jack of the amplifier. Doing so will lead to breakdown.

Firmly plug in the power plug. An imperfect connection will cause noise to be generated.

Bundling the connection cables together with the power cable will cause hum or other noise.

When the power plug is disconnected from the power outlet, wait about 5 seconds before reinserting.

7

Image 7
Contents CDR-W1500 Certification Safety InstructionsShould be serviced by qualified service personnel Labels for U.S.A. model only@2@1 @7@5@6 @3@4 @8@9 English Francais Español About CD-R/RW Discs FeaturesDisc Handling and Precautions Restrictions Related to the CD-R/RW Standards ConnectionsDisplay indications Part Names and FunctionsRear Panel Front PanelRemote Control Unit Relay Mode Setup MethodCharacter Setting of the Auto Track Mark ATM Setup MethodSetting the Synchro Recording Mode Setting the Synchro Recording LevelSetting of the Custom Index Fade-in time settingFade-out time setting Setting of the intro play time for scan recordingTimer playback is possible. See Main unit Copying ProcedureSetting the Skip Play Mode Timer play mode settingCopying one track at a time Copying entire discsRecording Modes Recording from External DevicesSome remarks on recording Manual recording Starting analog recording Main unit Remote control unit Select the CD-R sideStarting digital recording Adding track numbers during recording Stopping recordingStopping recording temporarily Disc Synchro Synchronized recording of the DiscSynchronized recording of the single track 1Tr Synchro Normal Playback Searching forward Various Playback FunctionsNot displayed properly Moving back to the beginning of the current trackDuring playback, press the pause button 3 Pause Off ALL button repeatedly until the Repeat indicator turnsRepeat A- indicator lights Select the deck to be operated Remote control unitPlaying all tracks repeatedly All Track Repeat Connections Relay ModeRelay mode Timer playbackMain unit Mix modeRelay play Mix programmed playbackMix random playback Dual modeDual playback Manual finalizing Finalizing CD-R/RW DiscManual recording from the CD section Auto finalizingErasing the tracks EditingErasing one or more tracks away from the last track 9,10Switch on the power Example Input mode Keys on the remote control unitSpecial character input mode Adding track titlesErasing track titles Erasing disc titlesMenu Mode Menu ModeErasing all the track titles and the disc title Message Meaning MessagesMain Specifications TroubleshootingCheck Again Before Assuming The Player Is Malfunctioning Disques pouvant être utilisés avec cet appareil Precautions Pendant LutilisationFonctions AU Sujet DES Disques CD-R/RWManipulation DES Disques ET Precautions a Prendre Restrictions Imposees PAR LES Normes SUR LES CD-R/RW ConnexionsIndications daffichage Noms DES Composants ET Leurs FonctionsPanneau avant Panneau arrièreTelecommande Insertion de disque Methode DE ParametrageRéglage du niveau denregistrement synchronisé Unité principale TélécommandeRéglage du mode enregistrement synchronisé Méthode de paramétrageRéglage de la durée de fondu de fin de piste Réglage de la durée du fondu de débutRéglage de lindex personnalisé Au sujet de la copie Procedure DE CopieRéglage du mode de lecture avec saut de piste 10 Réglage du mode de lecture temporiséeCopie dune piste à la fois Copie de disques entiersModes denregistrement Enregistrement a Partir DE Sources ExternesQuelques remarques sur lenregistrement Lancement dun enregistrement numérique Unité principale Télécommande Sélectionnez le côté CD-RAjout de numéros de piste pendant lenregistrement Arrêt de lenregistrementArrêt temporaire de lenregistrement Enregistrement synchronisé dune seule piste 1Tr Synchro Denregistrement et activez le mode stopSélectionnez le mode de copie synchronisée de piste Enregistrement synchronisé de disqueLancement de la lecture Lecture NormaleEnregistrement avec fondu de début Enregistrement avec fondu de finRecherche avant Diverses Fonctions DE LecturePendant la lecture, appuyez sur la touche pause 3 Pause Déplacement arrière au début de la piste actuelleDe toutes les pistes 1/ALL Lecture à répétition de toutes les pistes All Track Repeat Sélectionnez la platine à être sélectionner TélécommandeConnexions Mode RelaisMode relais Lecture temporiséeUnité principale Lecture en relais Mode mixteSélectionnez le côté CD Télécommande Lecture mixte programméeLecture double Mode double DualTélécommande Unité principale Lecture aléatoire mixteFinalisation manuelle Finalisation DE Disques CD-R/RWEnregistrement manuel à partir de la section CD Finalisation automatiqueEffacement des plages EditionEnregistrement des pistes que vous ne souhaitez pas écouter Activez lalimentation Ajout de titre de disqueRépétez létape 7 pour ajouter une autre annulation Mno Ajout de titres de pisteDef # % GhiEffacement des titres de piste Effacement de titres de disqueMode Menu Mode MenuEffacement de tous les titres de disque et de piste Message Signification Caracteristiques Principales Depistage DES PannesDiscos que pueden utilizarse con esta uinidad FuncionesPrecauciones Durante EL USO Acerca DE LOS Discos CD-R/RWManipulación DE Discos Y Precauciones Limitaciones Relacionadas CON LO Estándares DE CD-R/RW ConexionesIndicaciones de pantalla Nombres DE Piezas Y FuncionesPanel posterior Panel frontalUnidad DE Mando a Distancia Dubbing Normal Método DE ConfiguraciónAjuste del nivel de grabación sincronizada Método de configuraciónUnidad principal Unidad de mando a distancia Ajuste del modo de grabación sincronizadaAjuste de tiempo de fundido de salida Ajuste de tiempo de fundido de entradaAjuste del Índice Personalizado Acerca del copiado Procedimiento DE CopiadoAjuste del modo de reproducción de salto Ajuste del modo de reproducción por temporizadorCopia de una pista por vez Copia de discos enterosMModos de grabación Grabación Desde Dsipositiovs ExternosAlgunas observaciones sobre la grabación Comenzar grabación digital Grabación manual Comenzar grabación analógicaSecciones en blanco. Véase la página Detención de la grabaciónAdición de números de pista durante la grabación Durante la grabación pulse el botón de detención 2 StopAjuste el modo de detención Grabación sincronizada del discoGrabación y ajuste el modo de detención Grabación sincronizada de pistas individuales 1Tr SynchroGrabación con fundido de salida Reproducción NormalGrabación con fundido de entrada y de salida Grabación con fundido de entradaBúsqueda hacia adelante Diversas Funciones DE ReproducciónMovimiento hacia atrás al comienzo de la pista actual Apague el indicador Repeat El botón de repetición 1/ALL repetidamente hasta que seOtra vez Conexiones Modo DE RepeticiónMModo de repetidor Reproducción por temporizadorContinuación se iluminará el indicador Relay Pulse el botón Relay Mode y seleccione Relay PlayReproducción de repetidor Modo de mezcla Reproducción programada de mezclaModo dual Reproducción aleatoria de mezclaReproducción dual Finalización manual Finalización DE Discos CD-R/RWGrabación manual desde la sección de CD Finalización automáticaBorrar las pistas EdiciónRegistro de las pistas que no se desean escuchar Borrado de una o más pistas alejadas de la última pistaAdición de títulos de discos Adición de títulos de pistas Borrado de títulos de pistas Borrado de títulos de discosModo DE Menú Modo DE MenúMensaje Siginificado MensajesEspecificaciones Principales Solución DE Problemas14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan