Tripp Lite 30kVA Adding or Replacing Internal Batteries, Remote Emergency Power OFF EPO

Page 11

Communications (continued)

REMOTE EMERGENCY POWER OFF (EPO)

This optional feature is only for those applications which require connection to a facility's Emergency Power Off (EPO) circuit. When the UPS System is connected to this circuit, it enables emergency shutdown of the output. Using a user-supplied cable, connect the UPS System's EPO port to a user- supplied remote switch. The EPO port is not a phone line surge suppressor; do not connect a phone line to this port. The pin assignments for the EPO port are shown in the following diagram. Note: if there is a short between pins 2 and 3, 2 and 5, 4 and 5, or 3 and 4, the UPS system will power off. To reset from a Remote Emergency Power Off Shutdown, make sure there is AC line input power present, the Input Breakers are ON, and the shutdown- signal has been removed from the EPO circuit. Press the front panel “OFF” Button for 2 to 3 seconds (until a beep is heard); this will place the UPS System in “Bypass Mode.” Then, press the “ON” Button for one second. The UPS will re-start if AC line power is present.

Pin assignment:

X 1

X

2

3

4

5

6

Adding or Replacing Internal Batteries

DANGER!

POTENTIALLY LETHAL HIGH VOLTAGE! FOR QUALIFIED ELECTRICIANS ONLY!

Follow all safety precautions in the Safety section before adding or replacing internal batteries.

DANGER!

DO NOT REMOVE BATTERY SLEEVE!

Do not remove the plastic sleeve covering the battery strings. The sleeve is designed to prevent accidental contact with the terminals on the individual batteries. Contact with the terminals will create a potential for serious injury or death from lethal high voltage. Do not allow tools or other metal objects to come in contact with the terminals.

CAUTION!

BATTERY PACKS ARE HEAVY!

Use assistants as needed.

WARNING!

CHECK BATTERY PACK VOLTAGE BEFORE COMPLETING INSTALLATION

Do not install battery packs with DC voltages outside the acceptable range. (They may compromise battery backup capabilities).

NOTE!

Each battery pack consists of two strings of batteries: one string with a BLACK cable and one string with a RED cable.

The batteries are designed for hot-swap replacement, which allows connected equipment to continually receive AC mains power (but not battery backup support in the event of a blackout) during the battery installation procedure. See “Operation of Manual Bypass Switch” in the Operation section. Although the batteries can be hot-swapped, qualified service personnel may want to completely turn the UPS off during battery installation. See “Turning the UPS Off” in the Operation section.

Internal battery packs must be replaced by equivalent batteries available from Tripp Lite. Adding battery packs will increase recharge time. Individual models may vary slightly from diagrams.

11

Image 11
Contents Registration WarrantyUPS Connection Warnings Important Safety WarningsBattery Warnings UPS Location WarningsControl Panel Front PanelBattery Access Panel cover removed Rear Panel Rear PanelUPS Location InstallationMounting Bracket Installation UPS Input and Output Hardwire ConnectionTurning the UPS on Initial Battery ChargingSELF-TESTING Operation Normal ConditionsOperation on BYPASS-VOLTAGE OUT of Range Operation Special ConditionsLCD Display Select Button Inverter on Warnings Operation of Manual Bypass SwitchSwitching UPS to Bypass Mode Switching UPS to Normal ModeDRY Contact Interface CommunicationsRS-232 Interface AS-400 InterfaceCheck Battery Pack Voltage Before Completing Installation Remote Emergency Power OFF EPODo not Remove Battery Sleeve Battery Packs are HeavyInternal Battery Pack Wiring Diagram Adding or Replacing Internal Batteries Terminals Adding or Replacing Internal Batteries Warranty Registration ServiceWarranty & Warranty Registration Phase UPS System Limited WarrantyModel SU20K3/3XR5 SpecificationsModel SU20K3/3 Model SU30K3/3XR5 Model SU30K3/3Manual del Propietario Advertencias Sobre la Batería Advertencias de Seguridad ImportantesAdvertencias sobre la colocación y ubicación del UPS Advertencias para la conexión del UPSPanel DE Control Panel FrontalPanel DE Acceso a LA Bateria Tapa Removida Panel Frontal continuaciónPanel Trasero Panel TraseroConexion a Tierra InstalaciónUbicación DEL UPS Instalacion DE LOS Soportes DE MontajeApagando EL UPS Operación Condiciones NormalesCarga Inicial DE LA Bateria Encendiendo EL UPSOperacion EN DERIVACION-VOLTAJE Fuera DE Rango Operación Condiciones Normales continuaciónOperación Condiciones Especiales Boton Select Seleccionar DE LA Pantalla LCDOperación Condiciones Especiales continuación Interfaz DEL Contacto Seco ComunicacionesInterfaz RS-232 Interfaz AS-400¡NO Remueva LA Cubierta Protectora DE LA Bateria Comunicaciones continuaciónAñadiendo o Remplazando las Baterías Internas Apagado DE Emergencia Remoto EPOAñadiendo o Remplazando las Baterías Internas continuación Diagrama DEL Cableado DEL Modulo DE Baterias InternasAñadiendo o Remplazando las Baterías Internas continuación Terminales ¡PELIGRO ¡OBSERVE LA Polaridad Correcta Garantía Limitada del Sistema UPS Trifásico ServicioGarantía Modelo SU20K3/3XR5 EspecificacionesModelo SU20K3/3 Modelo SU30K3/3XR5 Especificaciones continuaciónModelo SU30K3/3 Manuel du propriétaire Mises en garde relatives aux connexions de léquipement Importantes consignes de sécuritéMises en garde relatives à la localisation de londuleur Mises en garde relatives aux connexions de londuleurPanneau avant Panneau DE CommandePanneau Daccès AUX Batteries carter enlevé Panneau avant suitePanneau Arrière Panneau arrièreSélection DU Câblage IL Faut Installer Londuleur À Laide DE Brides DE FixationMises EN Garde Relatives À LA Localisation DE Londuleur Connexion DE Mise À LA TerreFonctionnement Conditions normales Installation suiteFonctionnement EN DÉRIVATION-TENSION Hors Plag Fonctionnement Conditions normales suiteFonctionnement Conditions spéciales Bouton DE Sélection DE Lécran ACLFonctionnement Pendant UN Arrêt Commuter Londuleur EN Mode NormalFonctionnement Conditions spéciales suite Mises EN Garde Inverseur EN MarcheInterface Contact SEC Interface RS-232Interface AS-400 NE PAS Retirer LA Gaine DE Batterie Ajout et remplacement des batteries internesArrêt Durgence Emergency Power OFF EPO À Distance Communications suiteSchéma DU Câblage Interne DUN Bloc DE Batterie Ajout et remplacement des batteries internes suiteAjout et remplacement des batteries internes suite Bornes Ajout et remplacement des batteries internes suite Observer LA Bonne Polarité GarantieGarantie limitée de londuleur triphasé Modèle SU20K3/3XR5 SpécificationsModèle SU20K3/3 Modèle SU30K3/3 Modèle SU30K3/3XR5 Spécifications suiteTh Street Chicago, IL 60609 USA 773