Tripp Lite 3-Phase 20kVA UPS Location, Mounting Bracket Installation, Grounding Connection

Page 6

Installation

UPS LOCATION

Move your UPS over short distances using its wheels. NOTE: the wheels are not designed to provide long-term support for the UPS system after final installation. Mounting bracket installation is required.

MOUNTING BRACKET INSTALLATION

DANGER!

RISK OF PRODUCT DAMAGE AND SERIOUS PERSONAL INJURY

The UPS System's wheels are not designed to provide long-term support for the UPS system after final installation. MOUNTING BRACKET INSTALLATION IS REQUIRED. If the mounting brackets are not installed, the wheels may eventually fail and potentially damage the UPS System and cause serious personal injury.

Using the included bolts, install one mounting bracket on each side of the UPS System as shown. If desired, install the bracket to the floor surface with user-supplied hardware.

Front View

GROUNDING CONNECTION

Using a user-supplied 4 AWG ground wire, connect the UPS System's ground lug to earth ground. Tighten connections with a torque of not less than 35 inch-lbs. (3.9 NM). Keep ground wire connected at all times after installation.

Rear View

UPS INPUT AND OUTPUT HARDWIRE CONNECTION

In addition to the instructions listed below, follow all warnings found in the Safety section prior to connection.

•Install with flex cable of sufficient length to move UPS clear of surrounding equipment for servicing (sides and rear).

•Use ferrule caps to cover termination cables connected to UPS to avoid frayed ends from shorting on terminal block.

•Neutral conductor must be same size as current conductors.

WIRING SELECTION

Choose appropriate cabling (rated VW-1, FT-1 or better) to connect your UPS to an AC power supply and your equipment.

UPS System Model	Wiring Size
20kVA	6 AWG / 14 mm2
30kVA	4 AWG / 22 mm2

Maximum Cable Length: 10 m (32.8 ft)

6

Image 6

Contents Warranty RegistrationUPS Location Warnings Important Safety WarningsBattery Warnings UPS Connection WarningsFront Panel Control PanelBattery Access Panel cover removed Rear Panel Rear PanelUPS Input and Output Hardwire Connection InstallationMounting Bracket Installation UPS LocationOperation Normal Conditions Initial Battery ChargingSELF-TESTING Turning the UPS onOperation Special Conditions LCD Display Select ButtonOperation on BYPASS-VOLTAGE OUT of Range Switching UPS to Normal Mode Operation of Manual Bypass SwitchSwitching UPS to Bypass Mode Inverter on WarningsAS-400 Interface CommunicationsRS-232 Interface DRY Contact InterfaceBattery Packs are Heavy Remote Emergency Power OFF EPODo not Remove Battery Sleeve Check Battery Pack Voltage Before Completing InstallationInternal Battery Pack Wiring Diagram Adding or Replacing Internal Batteries Terminals Adding or Replacing Internal Batteries Phase UPS System Limited Warranty ServiceWarranty & Warranty Registration Warranty RegistrationSpecifications Model SU20K3/3Model SU20K3/3XR5 Model SU30K3/3 Model SU30K3/3XR5Manual del Propietario Advertencias para la conexión del UPS Advertencias de Seguridad ImportantesAdvertencias sobre la colocación y ubicación del UPS Advertencias Sobre la BateríaPanel Frontal Panel DE ControlPanel Frontal continuación Panel DE Acceso a LA Bateria Tapa RemovidaPanel Trasero Panel TraseroInstalacion DE LOS Soportes DE Montaje InstalaciónUbicación DEL UPS Conexion a TierraEncendiendo EL UPS Operación Condiciones NormalesCarga Inicial DE LA Bateria Apagando EL UPSBoton Select Seleccionar DE LA Pantalla LCD Operación Condiciones Normales continuaciónOperación Condiciones Especiales Operacion EN DERIVACION-VOLTAJE Fuera DE RangoOperación Condiciones Especiales continuación Interfaz AS-400 ComunicacionesInterfaz RS-232 Interfaz DEL Contacto SecoApagado DE Emergencia Remoto EPO Comunicaciones continuaciónAñadiendo o Remplazando las Baterías Internas ¡NO Remueva LA Cubierta Protectora DE LA BateriaDiagrama DEL Cableado DEL Modulo DE Baterias Internas Añadiendo o Remplazando las Baterías Internas continuaciónAñadiendo o Remplazando las Baterías Internas continuación Terminales ¡PELIGRO ¡OBSERVE LA Polaridad Correcta Servicio GarantíaGarantía Limitada del Sistema UPS Trifásico Especificaciones Modelo SU20K3/3Modelo SU20K3/3XR5 Especificaciones continuación Modelo SU30K3/3Modelo SU30K3/3XR5 Manuel du propriétaire Mises en garde relatives aux connexions de londuleur Importantes consignes de sécuritéMises en garde relatives à la localisation de londuleur Mises en garde relatives aux connexions de léquipementPanneau DE Commande Panneau avantPanneau avant suite Panneau Daccès AUX Batteries carter enlevéPanneau arrière Panneau ArrièreConnexion DE Mise À LA Terre IL Faut Installer Londuleur À Laide DE Brides DE FixationMises EN Garde Relatives À LA Localisation DE Londuleur Sélection DU CâblageInstallation suite Fonctionnement Conditions normalesBouton DE Sélection DE Lécran ACL Fonctionnement Conditions normales suiteFonctionnement Conditions spéciales Fonctionnement EN DÉRIVATION-TENSION Hors PlagMises EN Garde Inverseur EN Marche Commuter Londuleur EN Mode NormalFonctionnement Conditions spéciales suite Fonctionnement Pendant UN ArrêtInterface RS-232 Interface AS-400Interface Contact SEC Communications suite Ajout et remplacement des batteries internesArrêt Durgence Emergency Power OFF EPO À Distance NE PAS Retirer LA Gaine DE BatterieAjout et remplacement des batteries internes suite Schéma DU Câblage Interne DUN Bloc DE BatterieAjout et remplacement des batteries internes suite Bornes Ajout et remplacement des batteries internes suite Garantie Garantie limitée de londuleur triphaséObserver LA Bonne Polarité Spécifications Modèle SU20K3/3Modèle SU20K3/3XR5 Spécifications suite Modèle SU30K3/3 Modèle SU30K3/3XR5Th Street Chicago, IL 60609 USA 773