Panasonic EYFLA2A, EYFLA2Q Tightening Torque Chart for Reference Use, Using the Interval Set

Page 11

You can select from 30 torque clutch settings (1 to 30).

Use figures from the Tightening Torque Chart to guide your selection of torque clutch setting. (See the following tighten- ing torque chart)

2.Press the OK button to accept the select- ed torque clutch setting.

The control panel will stop flashing and light up.

CAUTION:

You must press the OK button in order for the selected setting to take effect.

Be sure to verify the new value after changing the setting. (See page 11.)

Tightening Torque Chart (for Reference Use)

The values illustrated on this chart were mea- sured under the conditions described below and are provided for reference purposes. Actual tightening torque varies with ambient conditions (the particular bolt being tightened, hardware being used, method of holding the bolt in place, etc.).

N • m

 

 

 

 

 

60

 

 

 

 

 

 

50

 

 

 

 

 

EYFLA3 (M10)

 

 

 

 

 

 

40

 

 

 

 

 

 

 

 

 

 

 

 

EYFLA2 (M8)

30

 

 

 

 

EYFLA3 (M8)

 

 

 

 

 

20

 

 

 

 

 

 

 

 

 

 

 

 

EYFLA1 (M8)

10

 

 

 

 

 

EYFLA2 (M6)

 

 

 

 

 

 

 

 

 

 

 

 

EYFLA1 (M6)

0

 

 

 

 

 

 

1

2 3

4 5

6

7

8

9 10 111213 1415 16171819202122232425 26272829 30

Measurement conditions

• Temperature: Room temperature (20°C/68°F)

Using the Interval Set

The interval set operates to prevent the tool from operating after it automatically stops as a result of the torque control function, even if the switch is engaged.

1.Set the tool to configuration mode. (See page 10.)

2.Press the interval set button.

The control panel will begin flashing.

Display: The number 0 flashes on and off.

Battery indication lamp: The middle bar of the battery flashes on and off.

Display

Battery indication lamp

3.

Press the

and

buttons to set the

 

desired time.

 

 

 

 

Buttons

Display

Seconds

 

 

30

 

3

 

 

1

 

0.1

 

 

0

 

Off

4. Press the OK button to accept the select-

 

ed setting.

 

 

 

 

• The control panel will stop flashing and

 

light up, and the torque clutch setting

 

will be displayed.

 

 

CAUTION:

Be sure to verify the new value after changing the setting.

Initializing All Settings

Factory settings

Torque clutch setting: “F” (torque con- trol function off)

Interval setting: 0 (off)

This section explains how to revert all tool settings to their default values at the time of shipment from the factory.

The error display will be turned off.

1.Set the tool to configuration mode. (See page 10.)

2.Press the format button.

The control panel will begin flashing.

Display: The letter “F” flashes on and off.

Battery indication lamp: The upper and lower bars of the battery flash on and off.

Display

Battery indication lamp

- 11 -

Image 11
Contents EYFLA2Q / EYFLA3J Model No EYFLA1A / EYFLA2AIndex/Index/Indice Page Power Tool Use and Care Work Area SafetyElectrical Safety Personal SafetyII. Intended USE III.ADDITIONAL Safety RulesBattery Tool Use and Care ServiceRemoving Socket IV. AssemblyAttaching Socket Attaching or Removing BitOperation Main Body Switch and Forward/Reverse Lever OperationWireless remote control range Insert the batteryTightening confirmation lamp Forward Rotation Switch OperationReverse Rotation Switch Operation Control PanelIndicator Battery indication lampAutomatic power-off function Indicator Battery statusConfiguring the torque clutch setting Setting the tool to configuration modeInitializing All Settings Tightening Torque Chart for Reference UseUsing the Interval Set Display Checking Tool SettingsDisplay Likely cause Error DisplayBattery Pack For Appropriate Use of Bat­ tery Pack Li-ion Battery Pack EYFB30Before charging the bat­ tery VI. MaintenanceVII. Accessories Battery Charger ChargingMain Unit VIII.SPECIFICATIONSLi-ion battery pack Battery Pack not included with shipmentBattery Charger not included with shipment Remote control not included with shipmentSécurité personnelle Consignes DE SECU­Sécurité de la zone de travail Sécurité électriqueUtilisation et soins de la batterie de l’outil Utilisation et soins de l’outil méca­ niqueFixation ou retrait d’une mèche II. Utilisation PrevueSupplementaires IV. MontageFixation ou retrait de la bat­ terie autonome FonctionnementPour fixer la douille Pour retirer la douilleUtilisation du commutateur pour une rotation en sens normal Portée de la télécommande sans filCorps principal Témoin indicateur de la batterie Panneau de commandeTémoin de confirmation de serrage Lumière DELIndicateur Fonction de commande du couple de serrageFonction d’arrêt automatique Etat de la batterieConfiguration du réglage de l’embrayage du couple de serrage Réglage de l’outil dans le mode configurationInitialisation de tous les réglages Graphique du couple de serrage Pour référenceUtilisation du réglage de l’intervalle Affichage Circuit de l’outil Vérification des réglages de l’outilAction correctrice Affichage d’erreurAffichage Cause probable Avant de charger la batterie VI. EntretienBatterie Chargeur de batterie RechargeVIII.CARACTERISTIQUES Techniques VII.ACCESSOIRESBatterie autonome Li-ion Télécommande non inclue dans l’expéditionBatterie Autonome non inclue dans l’expédition Chargeur DE Batterie non inclue dans l’expédition¡ADVERTENCIA! Lea todas las instrucciones Seguridad del lugar de trabajoSeguridad eléctrica Seguridad personalUso y cuidado de la herramienta a batería Uso y cuidados de herramientas eléctricasColocación o extracción de la broca II. USO PretendidoIII.REGLAS DE SEGURI­ DAD Adicionales IV. MontajeColocación y extracción de la batería FuncionamientoInstalación del cubo Remoción del cuboRango de control remoto inalámbrico Cuerpo principalLámpara indicadora de la batería Panel de controleLámpara de confirmación de apriete Luz LEDIndicador Función de apagado automáticoFunción de control de par de torsión Indicador Estado de la bateríaAjuste de la herramienta al modo de con­ figuración Configuración del ajuste de embrague del par de torsiónInicialización de todos los ajustes Uso del juego de intervaloVerificación de los ajustes de herramienta Acción correctiva Visualización de errorVisor Causa probable Antes de cargar la batería VI. MantenimientoBloque de pilas Para un uso adecuado de la batería Cargador de la batería CargaVIII.ESPECIFICACIONES VII.ACCESORIOSBatería de Li-ión Batería no se incluye con el embarqueCargador DE Batería no se incluye con el embarque Control remoto no se incluye con el embarqueMemo Memo Memo Panasonic Consumer Electronics Company