Porter-Cable 333VS Functional Description, Assembly, Foreword, INSTALLING/REMOVING Abrasive Disc

Page 10

FUNCTIONAL DESCRIPTION

FOREWORD

The Porter-Cable Random Orbit Sanders provide rapid stock removal with 80 to 100 grit paper and swirl-free finishing with 120-150 grit paper. Model 332 is equipped to accept 5" diameter STIKIT™ adhesive paper backed abrasives. Model 333 is equipped to accept 5" hook & loop backed abrasives with five dust extraction holes. Model 333VS is equipped to accept 5" hook & loop backed abrasives with five or eight dust extraction holes. Model 334 is equipped to accept 5" diameter STIKIT™ adhesive backed abrasives with five dust extraction holes.

ASSEMBLY

ASSEMBLY TOOLS REQUIRED - None ASSEMBLY TIME ESTIMATE - 15 to 30 minutes

AB

A

Fig. 1

Fig. 1A

INSTALLING/REMOVING ABRASIVE DISC

Models 332 and 334:

1. DISCONNECT TOOL FROM POWER SOURCE.

2.Place machine on workbench with pad up (see Fig. 2).

3.Clean dust from pad face.

4.Tear a new abrasive disc from roll and position disc to the sander pad. Align the dust extraction holes in paper with holes in pad (334 ONLY).

5.Press disc firmly onto pad.

6.Position machine with abrasive contacting scrap material. Start machine and operate momentarily while exerting firm pressure to seat disc to pad.

Failure to properly seat disc to pad may result in disc being thrown from pad causing personal injury.

7.To remove disc, peel disc away from pad.

NOTE: Do not store machine with an abrasive disc installed. Heat generated by the sanding operation increases the adhesive bond between the disc and pad. If disc is left on pad for an extended time after use, it can become difficult to remove.

10

Image 10

Contents Model ModelsTable of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules General Safety Rules Additional Specific Safety Rules Symbol Definition Additional Safety Rules for Paint Removal Motor Carton ContentsExtension Cord Selection Functional Description AssemblyINSTALLING/REMOVING Abrasive Disc ForewordModels 333 and 333VS Dust Collector Models 333, 333VSTo Start and Stop Sander HOW to Hold SanderOperation Speed Control 333VSWear Safety Glasses and Dust Mask Troubleshooting MaintenanceUsing the Sander PAD BrakeFailure to Start Belt ReplacementKeep Tool Clean LubricationService AccessoriesWarranty PORTER-CABLE Limited ONE Year WarrantyModelos ModeloImportante Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNormas Generales DE Seguridad Normas Generales DE Seguridad continuación Normas Específicas DE Seguridad Y Símbolos Símbolo Definición Guarde Estas Instrucciones Contenido DE Carton Selección DE Cables DE ServicioPrologo Descripción FuncionalAsamblea Para Poner EN Marcha Y Parar LA LijadoraModelos 333 y 333VS Para Instalar Y Remover LOS Discos Abrasivos Modelos 332 yDesconecte LA Lijadora DE LA Fuente DE Electricidad Captador DE Polvo Modelos 333, 333VS y OperaciónComo Agarrar LA Lijadora Usando LA Lijadora Localizacion DE FallasEL Freno Para EL Cojin Lleve Anteojos DE Seguridad Y UNA Mascara Contra EL PolvoPara Cambiar EL Cojin MantenimientoReemplazo DE LA Cinta Lubricación Mantenga LAS Herramientas LimpiasFalla DE Ponerse EN Marcha Inspección DE Escobillas Carbones Si aplicablePiezas DE Repuesto ServicioAccesorios Mantenimiento Y ReparacionesGarantia Póliza DE Garantía Limitada DE 1 AÑO DE PORTER-CABLEModèle 332 Modèles 333 etInstructions DE Sûreté Importantes Mesures DE Sécurité DéfinitionsRègles Générales SUR LA Sécurité Règles Générales SUR LA Sécurité suite Consignes DE Sécurité ET Symboles Spécifiques Symbole Définition Conservez CES Instructions Moteur Contenus DE BoiteSélection DU Cordon DE Rallonge Assemblée Commande DE Vitesse No VS seulementDescription Fonctionnelle AVANT-PROPOSModèles 333 et 333VS POSE/DÉPOSE DU Disque AbrasifModèles 332 et Mise EN Garde Débranchez L’OUTIL DE LA Prise DE CourantComment Tenir LA Ponceuse OpérationFrein DE Patin Guide DE Depannage Utilisation DE LA PonceuseRéparation Entretien Remplacement DU Coussinet D’APPUIRemplacement DE LA Courroie Mise EN Garde Débranchez LA Ponceuse DE LA Prise DE CourantGraissage Nettoyer VOS Outils’OUTIL Refuse DE Démarrer Inspection DES Balais Le cas échéantAccessoires GarantieWOODWORKER’S Choice