Porter-Cable 333VS Belt Replacement, Keep Tool Clean, Failure to Start, Lubrication

Page 14

BELT REPLACEMENT

1. DISCONNECT TOOL FROM POWER SOURCE.

2.Remove back-up pad (see CHANGING BACK-UP PAD).

3.Remove the old belt and clean the belt mounting area.

4.Position the new belt around pulley (A) Fig. 10, and start it onto the shoulder of the pad support (B).

5.Rotate the pad support as you “walk” the belt onto it (see Fig. 11).

6.Reassemble back-up pad (see CHANGING BACK-UP PAD).

BELT

B

A

SHOULDER

Fig. 10

Fig. 11

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary.

BRUSH INSPECTION (If applicable)

For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh lubricant. Have new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.

14

Image 14

Contents Model ModelsTable of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules General Safety Rules Additional Specific Safety Rules Symbol Definition Additional Safety Rules for Paint Removal Extension Cord Selection Carton ContentsMotor Functional Description AssemblyINSTALLING/REMOVING Abrasive Disc ForewordModels 333 and 333VS Dust Collector Models 333, 333VSTo Start and Stop Sander HOW to Hold SanderOperation Speed Control 333VSWear Safety Glasses and Dust Mask Troubleshooting MaintenanceUsing the Sander PAD BrakeFailure to Start Belt ReplacementKeep Tool Clean LubricationService AccessoriesWarranty PORTER-CABLE Limited ONE Year WarrantyImportante ModeloModelos Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNormas Generales DE Seguridad Normas Generales DE Seguridad continuación Normas Específicas DE Seguridad Y Símbolos Símbolo Definición Guarde Estas Instrucciones Contenido DE Carton Selección DE Cables DE ServicioPrologo Descripción FuncionalAsamblea Para Poner EN Marcha Y Parar LA LijadoraDesconecte LA Lijadora DE LA Fuente DE Electricidad Para Instalar Y Remover LOS Discos Abrasivos Modelos 332 yModelos 333 y 333VS Como Agarrar LA Lijadora OperaciónCaptador DE Polvo Modelos 333, 333VS y Usando LA Lijadora Localizacion DE FallasEL Freno Para EL Cojin Lleve Anteojos DE Seguridad Y UNA Mascara Contra EL PolvoReemplazo DE LA Cinta MantenimientoPara Cambiar EL Cojin Lubricación Mantenga LAS Herramientas LimpiasFalla DE Ponerse EN Marcha Inspección DE Escobillas Carbones Si aplicablePiezas DE Repuesto ServicioAccesorios Mantenimiento Y ReparacionesGarantia Póliza DE Garantía Limitada DE 1 AÑO DE PORTER-CABLEModèle 332 Modèles 333 etInstructions DE Sûreté Importantes Mesures DE Sécurité DéfinitionsRègles Générales SUR LA Sécurité Règles Générales SUR LA Sécurité suite Consignes DE Sécurité ET Symboles Spécifiques Symbole Définition Conservez CES Instructions Sélection DU Cordon DE Rallonge Contenus DE BoiteMoteur Assemblée Commande DE Vitesse No VS seulementDescription Fonctionnelle AVANT-PROPOSModèles 333 et 333VS POSE/DÉPOSE DU Disque AbrasifModèles 332 et Mise EN Garde Débranchez L’OUTIL DE LA Prise DE CourantFrein DE Patin OpérationComment Tenir LA Ponceuse Guide DE Depannage Utilisation DE LA PonceuseRéparation Entretien Remplacement DU Coussinet D’APPUIRemplacement DE LA Courroie Mise EN Garde Débranchez LA Ponceuse DE LA Prise DE CourantGraissage Nettoyer VOS Outils’OUTIL Refuse DE Démarrer Inspection DES Balais Le cas échéantAccessoires GarantieWOODWORKER’S Choice