Bosch Power Tools FNH180K-16, FNH180-16BN manual Cold Weather Operation, Nail Unloading, TOO Deep

Page 11

! WARNING

BM 2610034445 03-14_FNH180 3/27/14 11:52 AM Page 11

COLD WEATHER OPERATION

When using the tool in cold conditions the tool will cycle slower than usual while driving the first nails. The cycle rate will increase as the tool warms up. Keep tool warm to avoid reduced cycle rate.

Do not use a frozen tool. ! WARNING Allow tool to thaw before

using. Moisture frozen in the tool may impede internal components resulting in the risk of injury and/or tool damage.

NAIL UNLOADING

Always disconnect battery ! WARNING pack from tool before

removing nails from magazine. This avoids the risk of unintentional operation.

Do not disconnect battery ! WARNING pack from the tool with

finger on trigger or work contact element depressed. The tool can fire when reconnected to battery pack.

1. Disconnect battery pack.

2. Pull back follower, pressing bypass lever of the follower to allow follower to bypass nails and slowly allow follower to return to nose of the tool, see figure 8.

3. Tilt the tool with the magazine vertical and the nose facing up, this will allow the nails to slide to the back of the magazine.

4. Once the nails have slid back to the hold back spring, press the tab on the hold back spring to push the spring back and allow the nails to come out of the magazine, see figure 9.

Do not allow the nail follower to freely recoil.

Guide the follower by hand until it reaches its full forward position. Free recoil of the follower could result in damage to the follower and/or magazine or your fingers could become pinched.

DEPTH OF DRIVE ADjUSTMENT

The depth with which nails are driven into the work piece can be adjusted using the depth adjustment on the housing.

Disconnect the battery pack ! WARNING from tool before making

adjustments. Such precautionary safety measures reduce the risk or unintentional tool operation.

1. Disconnect tool from battery pack.

2. Remove nails from tool as described in the “Nail Unloading” section of this manual.

3.Adjust tool driving depth:

•To reduce the nail depth, turn the adjustment knob towards the “flush” icon, see figure 10.

FIG. 8	PRESS
	Bypass Lever

		E
	LID		D
S			D
		AR
RW
FO

RELEASE

NAILS

FIG. 9

			S
		S
	E
R
P

	Turn the adjustment	FIG. 10
	knob counter	FIG. 10
	knob counter
	clockwise.

TOO DEEP

FIG. 11	Turn the adjustment
	Turn the adjustment
	knob clockwise.
	TOO SHALLOW

-11-

Image 11

Contents Ver la página Read Before UsingLeer antes de usar Personal safety General Power Tool Safety WarningsWork area safety Electrical safetyService Safety Rules for Cordless Nailer ToolsBattery tool use and care BM 2610034445 03-14FNH180 3/27/14 1152 AM Additional Safety Warnings Symbol Name Designation/Explanation SymbolsSymbols Cordless Nailer Tool Functional Description and SpecificationsLubrication Nail Loading AssemblyLOCK-OUT Switch Operating InstructionsFiring Modes Nail Hold Back Spring Release Bypass Lever SLITOO Deep Cold Weather OperationNail Unloading Page Inserting and Releasing BATTERy Pack Storage MaintenanceCleaning No-Mar Tip AccessoriesProblem Trouble Tool will not Start Trouble Shooting GuideTrouble Tool Operates PROPERLy Motor Runs ProblemProblem Trouble Driver Blade Stuck Down does not Return REMEDyTrouble jAMMED Fastener PIN #1 Replacing Return SystemCorrect To replace drive blade, follow steps below Replacing Driver BladePIN #1 Page Correct Page Sécurité électrique Sécurité du lieu de travailEntretien Consignes de sécurité pour les cloueuses sans cordonUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesBM 2610034445 03-14FNH180 3/27/14 1152 AM Le plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Cloueuse sans cordon Description fonctionnelle et spécificationsConsignes de fonctionnement AssemblageCharge DES Clous Maximum Modes D’EJECTION PAS Assez Profond Fonctionnement PAR Temps FroidLevierBypassde Leverdérivation Page Insertion ET Retrait DU BLOC-PILES Nettoyage EntretienAccessoires Problème L’OUTIL NE SE MET PAS EN Marche Guide de dépannagePossible Guide de dépannage suiteAbaissée Elle NE Retourne PAS Dans SA Position Initiale CauseProblème Trou Coincé Cheville N Remplacement du circuit de retourCorrecte Remplacement de la lame du mécanisme d’entraînement Ensemble de bloc d’entraînement BM 2610034445 03-14FNH180 3/27/14 1152 AM Correcte Tirez Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías Page Advertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosSímbolos continuación Interruptor Botón DE Liberación DEL Paquete DE BateríasBaterías Mango GatilloInstrucciones de funcionamiento EnsamblajeModos DE Disparo AciaDemasiado Profundo Utilizacion EN Tiempo FrioSUE CLA En el sentido de lasDespeje DE Atascos Reconecte el paquete de bateríaIntroducción Y Suelta DEL Paquete DE Baterías Limpieza MantenimientoServicio Accesorios Remedio Guía de resolución de problemasDificultad LA Herramienta no Arranca Dificultad Hoja DEL Impulsor Atorada no Regresa Guía de resolución de problemas continuaciónProblema Dificultad Sujetador Atorado Jalar Pasador no Reemplazo del sistema de regresoCorrecto Jalar Reemplazo de la hoja del impulsorEmpujar Pasador no Simplemente empújelos de vuelta a su sito Fig Incorrecto Empujar BM 2610034445 03-14FNH180 3/27/14 1153 AM BM 2610034445 03-14FNH180 3/27/14 1153 AM 2610034445