Bosch Power Tools FNH180K-16, FNH180-16BN manual Replacing Return System, PIN #1

Page 19

BM 2610034445 03-14_FNH180 3/27/14 11:52 AM Page 19

 

Replacing Return System

 

Read instruction manual first! Remove battery pack and nails from the tool

! WARNING

 

before making adjustments, assembling accessories or servicing.

 

To replace rubber cords, follow steps below:

1.Remove metal cap. Using 3mm allen wrench, remove 3 screws and set aside (Fig. 15).

2.Remove drive block pin #1 by pushing on one side. Pull on other end to remove. *TIP* 16ga finish nail can be used to slide pin out (Fig. 16).

3.Locate pin #2. To remove, use pin #1 and push pin #2 from either side until enough of the pin has been exposed. Remove completely. Place both pins in secure place for reassembly (Fig. 17).

4.Sub Assembly. Holding tool securely with one hand, use other hand to remove driver

sub-assembly by grabbing both sides and then pull directly back (Fig. 18).

5.The Driver Sub Assembly consists of 5 parts (Fig. 19):

A)Driver Block Assembly (1)

B)Guide Rails (2)

C)Guide Sleeves (2)

D)Return Frame (1)

E)Rubber Cords (2)

6.Remove worn or damaged rubber cords. Align new rubber cords with tabs on the back of the return frame first (Fig. 20).

FIG. 15

 

FIG. 16

PIN #1

 

FIG. 18

 

 

FIG. 19

 

C

 

B

 

 

A

 

 

 

D

E

B

C

 

 

 

FIG. 17

FIG. 20

 

PIN #2

PIN #1

 

 

-19-

Image 19
Contents Leer antes de usar Read Before UsingVer la página Personal safety General Power Tool Safety WarningsWork area safety Electrical safetyBattery tool use and care Safety Rules for Cordless Nailer ToolsService BM 2610034445 03-14FNH180 3/27/14 1152 AM Additional Safety Warnings Symbol Name Designation/Explanation SymbolsSymbols Cordless Nailer Tool Functional Description and SpecificationsLubrication Nail Loading AssemblyLOCK-OUT Switch Operating InstructionsFiring Modes Nail Hold Back Spring Release Bypass Lever SLINail Unloading Cold Weather OperationTOO Deep Page Inserting and Releasing BATTERy Pack Cleaning MaintenanceStorage No-Mar Tip AccessoriesProblem Trouble Tool will not Start Trouble Shooting GuideTrouble Tool Operates PROPERLy Motor Runs ProblemProblem Trouble Driver Blade Stuck Down does not Return REMEDyTrouble jAMMED Fastener PIN #1 Replacing Return SystemCorrect To replace drive blade, follow steps below Replacing Driver BladePIN #1 Page Correct Page Sécurité électrique Sécurité du lieu de travailEntretien Consignes de sécurité pour les cloueuses sans cordonUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesBM 2610034445 03-14FNH180 3/27/14 1152 AM Le plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Cloueuse sans cordon Description fonctionnelle et spécificationsConsignes de fonctionnement AssemblageCharge DES Clous Maximum Modes D’EJECTION LevierBypassde Leverdérivation Fonctionnement PAR Temps FroidPAS Assez Profond Page Insertion ET Retrait DU BLOC-PILES Nettoyage EntretienAccessoires Problème L’OUTIL NE SE MET PAS EN Marche Guide de dépannagePossible Guide de dépannage suiteAbaissée Elle NE Retourne PAS Dans SA Position Initiale CauseProblème Trou Coincé Cheville N Remplacement du circuit de retourCorrecte Remplacement de la lame du mécanisme d’entraînement Ensemble de bloc d’entraînement BM 2610034445 03-14FNH180 3/27/14 1152 AM Correcte Tirez Seguridad eléctrica Seguridad del área de trabajoSeguridad personal Uso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones Page Advertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosSímbolos continuación Interruptor Botón DE Liberación DEL Paquete DE BateríasBaterías Mango GatilloInstrucciones de funcionamiento EnsamblajeModos DE Disparo AciaDemasiado Profundo Utilizacion EN Tiempo FrioSUE CLA En el sentido de lasDespeje DE Atascos Reconecte el paquete de bateríaIntroducción Y Suelta DEL Paquete DE Baterías Servicio MantenimientoLimpieza Accesorios Dificultad LA Herramienta no Arranca Guía de resolución de problemasRemedio Problema Guía de resolución de problemas continuaciónDificultad Hoja DEL Impulsor Atorada no Regresa Dificultad Sujetador Atorado Jalar Pasador no Reemplazo del sistema de regresoCorrecto Empujar Reemplazo de la hoja del impulsorJalar Pasador no Simplemente empújelos de vuelta a su sito Fig Incorrecto Empujar BM 2610034445 03-14FNH180 3/27/14 1153 AM BM 2610034445 03-14FNH180 3/27/14 1153 AM 2610034445