Bosch Power Tools FNH180-16BN, FNH180K-16 manual Maintenance, Cleaning, Storage

Page 14
! WARNING

BM 2610034445 03-14_FNH180 3/27/14 11:52 AM Page 14

Maintenance

Service

Maintenance performed by

!WARNING unauthorized personnel may result in misplacing of the internal components which could cause serious hazard. We recommend that all tool service be performed by a BOSCH factory service center or authorized BOSCH service station.

Contact your BOSCH service center for instructions and the following user replaceable parts; rubber cords, and driver block assembly.

For all other repairs contact your BOSCH service center.

BATTERIES

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready for use.

D.C. MOTORS

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

To avoid accidents, always disconnect the tool and/or charger from the power supply before

cleaning. The tool may be cleaned most effectively with com pressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Do not attempt to clean by ! WARNING inserting pointed objects through opening. Sharp edges may damage internal components causing a

serious hazard.

Ventilation openings, the work contact element, and the trigger must be kept clean and free of foreign matter.

Clean the magazine. Remove plastic or wooden chips which may have accumulated in the magazine.

Certain cleaning agents ! CAUTION and solvents damage

plastic and rubber parts. Some of these are: gasoline, car bon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Storage

When not in use, the tool should be disconnected and stored in the storage case in a warm and dry place.

Do not store the tool in a cold weather environment.

! WARNING

Keep out of reach of

children and personnel

unfamiliar with tool operation. Lock the storage area. Tools are dangerous in the hands of personnel unfamiliar with the tool.

-14-

Image 14
Contents Ver la página Read Before UsingLeer antes de usar Electrical safety General Power Tool Safety WarningsWork area safety Personal safetyService Safety Rules for Cordless Nailer ToolsBattery tool use and care BM 2610034445 03-14FNH180 3/27/14 1152 AM Additional Safety Warnings Symbols Symbol Name Designation/ExplanationSymbols Functional Description and Specifications Cordless Nailer ToolOperating Instructions AssemblyLOCK-OUT Switch Lubrication Nail LoadingNail Hold Back Spring Release Bypass Lever SLI Firing ModesTOO Deep Cold Weather OperationNail Unloading Page Inserting and Releasing BATTERy Pack Storage MaintenanceCleaning Accessories No-Mar TipTrouble Shooting Guide Problem Trouble Tool will not StartREMEDy ProblemProblem Trouble Driver Blade Stuck Down does not Return Trouble Tool Operates PROPERLy Motor RunsTrouble jAMMED Fastener Replacing Return System PIN #1Correct Replacing Driver Blade To replace drive blade, follow steps belowPIN #1 Page Correct Page Sécurité du lieu de travail Sécurité électriqueUtilisation et entretien des outils à piles Consignes de sécurité pour les cloueuses sans cordonUtilisation et entretien des outils Électroportatifs EntretienBM 2610034445 03-14FNH180 3/27/14 1152 AM Avertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombSymboles Symbole Nom Désignation/ExplicationSymboles suite Description fonctionnelle et spécifications Cloueuse sans cordonAssemblage Consignes de fonctionnementCharge DES Clous Maximum Modes D’EJECTION PAS Assez Profond Fonctionnement PAR Temps FroidLevierBypassde Leverdérivation Page Insertion ET Retrait DU BLOC-PILES Entretien NettoyageAccessoires Guide de dépannage Problème L’OUTIL NE SE MET PAS EN MarcheCause Guide de dépannage suiteAbaissée Elle NE Retourne PAS Dans SA Position Initiale PossibleProblème Trou Coincé Remplacement du circuit de retour Cheville NCorrecte Remplacement de la lame du mécanisme d’entraînement Ensemble de bloc d’entraînement BM 2610034445 03-14FNH180 3/27/14 1152 AM Correcte Tirez Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías Page Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Gatillo Botón DE Liberación DEL Paquete DE BateríasBaterías Mango InterruptorEnsamblaje Instrucciones de funcionamientoAcia Modos DE DisparoEn el sentido de las Utilizacion EN Tiempo FrioSUE CLA Demasiado ProfundoReconecte el paquete de batería Despeje DE AtascosIntroducción Y Suelta DEL Paquete DE Baterías Limpieza MantenimientoServicio Accesorios Remedio Guía de resolución de problemasDificultad LA Herramienta no Arranca Dificultad Hoja DEL Impulsor Atorada no Regresa Guía de resolución de problemas continuaciónProblema Dificultad Sujetador Atorado Reemplazo del sistema de regreso Jalar Pasador noCorrecto Jalar Reemplazo de la hoja del impulsorEmpujar Pasador no Simplemente empújelos de vuelta a su sito Fig Incorrecto Empujar BM 2610034445 03-14FNH180 3/27/14 1153 AM BM 2610034445 03-14FNH180 3/27/14 1153 AM 2610034445