Bosch Power Tools FNH180K-16 manual Problem, REMEDy, Trouble Tool Operates PROPERLy Motor Runs

Page 17

BM 2610034445 03-14_FNH180 3/27/14 11:52 AM Page 17

Trouble Shooting Guide (continued)

Many common problems can be solved easily by utilizing the chart below. For more serious or persistent problems, contact a Bosch service center or call 877-BOSCH-99.

!WARNING

PROBLEM

REMEDy

PROBLEM

Read instruction manual first! Remove battery pack and nails from the tool before making adjustments, assembling accessories or servicing.

TROUBLE: DRIVER BLADE STUCK DOWN (DOES NOT RETURN)

1.Jammed fastener

2.Damaged or worn return system

3.Debris in nosepiece

4.Damaged driver blade assembly

1.Remove battery pack from tool. Refer to “jam clearing” on page 12 for details.

2.Replace return system; see page 19 or see authorized service center

3.Clean nosepiece

4.Replace drive assembly; see page 21 or see authorized service center

TROUBLE: TOOL OPERATES, BUT DOES NOT DRIVE THE FASTENER FULLy

1.Battery pack not charged, or battery pack is damaged.

2.Depth adjustment set too shallow

3.Tool not firmly applied to workpiece

4.Material and fastener length too rigorous an application

5.Damaged or worn driver blade tip

6.Damaged or worn driver/return assembly

REMEDy 1. Charge or replace battery

2.Rotate depth adjustment wheel to a deeper setting

3.See instruction manual

4.Choose appropriate material or fastener length

5.Replace driver/return assembly; see page 21 or see authorized service center

6.Replace driver/return assembly; see page 21 or see authorized service center

TROUBLE: TOOL OPERATES PROPERLy (MOTOR RUNS AND

TOOL FIRES), BUT NO FASTENER DRIVEN

PROBLEM 1. No fasteners in magazine

2.Wrong size or angle fasteners

3.Debris in nosepiece

4.Debris in magazine

5.Worn magazine

6.Damaged or worn return system

7.Damaged or worn driver blade

8.Damaged follower spring

REMEDy 1. Load fasteners into magazine

2.Use only recommended fasteners

3.Clean nosepiece

4.Clean magazine

5.Replace magazine; see authorized service center

6.Replace return system; see page 19 or see authorized service center

7.Replace driver assembly; see page 21 or see authorized service center

8.Replace spring; see authorized service center

-17-

Image 17

Contents Ver la página Read Before UsingLeer antes de usar Work area safety General Power Tool Safety WarningsElectrical safety Personal safetyService Safety Rules for Cordless Nailer ToolsBattery tool use and care BM 2610034445 03-14FNH180 3/27/14 1152 AM Additional Safety Warnings Symbol Name Designation/Explanation SymbolsSymbols Cordless Nailer Tool Functional Description and SpecificationsLOCK-OUT Switch AssemblyOperating Instructions Lubrication Nail LoadingFiring Modes Nail Hold Back Spring Release Bypass Lever SLITOO Deep Cold Weather OperationNail Unloading Page Inserting and Releasing BATTERy Pack Storage MaintenanceCleaning No-Mar Tip AccessoriesProblem Trouble Tool will not Start Trouble Shooting GuideProblem Trouble Driver Blade Stuck Down does not Return ProblemREMEDy Trouble Tool Operates PROPERLy Motor RunsTrouble jAMMED Fastener PIN #1 Replacing Return SystemCorrect To replace drive blade, follow steps below Replacing Driver BladePIN #1 Page Correct Page Sécurité électrique Sécurité du lieu de travailUtilisation et entretien des outils Électroportatifs Consignes de sécurité pour les cloueuses sans cordonUtilisation et entretien des outils à piles EntretienBM 2610034445 03-14FNH180 3/27/14 1152 AM Le plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Cloueuse sans cordon Description fonctionnelle et spécificationsConsignes de fonctionnement AssemblageCharge DES Clous Maximum Modes D’EJECTION PAS Assez Profond Fonctionnement PAR Temps FroidLevierBypassde Leverdérivation Page Insertion ET Retrait DU BLOC-PILES Nettoyage EntretienAccessoires Problème L’OUTIL NE SE MET PAS EN Marche Guide de dépannageAbaissée Elle NE Retourne PAS Dans SA Position Initiale Guide de dépannage suiteCause PossibleProblème Trou Coincé Cheville N Remplacement du circuit de retourCorrecte Remplacement de la lame du mécanisme d’entraînement Ensemble de bloc d’entraînement BM 2610034445 03-14FNH180 3/27/14 1152 AM Correcte Tirez Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones MecánicasUso y cuidado de las herramientas Alimentadas por baterías Page Advertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosSímbolos continuación Baterías Mango Botón DE Liberación DEL Paquete DE BateríasGatillo InterruptorInstrucciones de funcionamiento EnsamblajeModos DE Disparo AciaSUE CLA Utilizacion EN Tiempo FrioEn el sentido de las Demasiado ProfundoDespeje DE Atascos Reconecte el paquete de bateríaIntroducción Y Suelta DEL Paquete DE Baterías Limpieza MantenimientoServicio Accesorios Remedio Guía de resolución de problemasDificultad LA Herramienta no Arranca Dificultad Hoja DEL Impulsor Atorada no Regresa Guía de resolución de problemas continuaciónProblema Dificultad Sujetador Atorado Jalar Pasador no Reemplazo del sistema de regresoCorrecto Jalar Reemplazo de la hoja del impulsorEmpujar Pasador no Simplemente empújelos de vuelta a su sito Fig Incorrecto Empujar BM 2610034445 03-14FNH180 3/27/14 1153 AM BM 2610034445 03-14FNH180 3/27/14 1153 AM 2610034445