Epson 28-276 instruction manual SAVE THESE Instructions, Additional Specific Safety Rules

Page 4

ADDITIONAL SPECIFIC SAFETY RULES

Failure to follow these rules may result in serious personal injury.

1.Do not operate this machine until it is assembled and installed according to the instructions.

2.Obtain advice from your supervisor, instructor, or another qualified person if you are not familiar with the operation of this tool.

3.Follow all wiring codes and recommended electrical connections.

4.Use the guards whenever possible. Check to see that they are in place, properly adjusted, secured, and working correctly.

5.Use proper blade size and type.

6.Adjust the upper blade guide so that it is about 1/8" above the workpiece.

7.Properly adjust the blade tension, tracking, blade guides, and blade support bearings.

8.Keep arms, hands, and fingers away from the blade.

9.Avoid awkward operations and hand positions where a sudden slip could cause a hand to move into the blade.

10.Never start the machine before clearing the table of all objects (tools, scrap pieces, etc.).

11.Never start the machine with the workpiece against the blade.

12.Hold workpiece firmly against the table. Do not attempt to saw a workpiece that does not have a flat surface against the table.

13.Hold workpiece firmly and feed into blade at a moderate speed.

14.Never reach under the table while the machine is running.

15.Turn the machine "off" to back out of an uncompleted or jammed cut.

16.Make "relief" cuts prior to cutting long curves.

17.Turn the machine "off" and wait for the blade to stop prior to cleaning the blade area, removing debris near the blade, removing or securing workpiece, or changing the angle of the table. A coasting blade can be dangerous.

18.Never perform layout, assembly, or set-up work on the table/work area when the machine is running.

19. Turn the machine "off" and disconnect the machine from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

20.Turn the machine "off", disconnect the machine from the power source, and clean the table/work area before leaving the machine. Lock the switch in the "off" position to prevent unauthorized use.

21.Additional information regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www. powertoolinstitute.Com).Informationisalsoavailable from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the american national standards institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

4 - English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Contractors Saw Important Safety Instructions Table of ContentsSafety Guidelines Definitions General SAFETY RULES ADDITIONAL SPECIFIC SAFETY RULES SAVE THESE InstructionsMOTOR SPECIFICATIONS Power ConnectionsGrounding Instructions EXTENSION CORDS Fig. CCarton Contents Functional DescriptionModel 28-206 Enclosed Stand Parts Model 28-276 Open Stand Parts Assembly Assembly Tools RequiredAssembly Time Estimate Model 28-206 Enclosed Stand AssemblyPage Model 28-276 Open Stand Assembly Page Attaching the Belt to the SAW and Motor Pulley Attaching the SAW to the StandAttaching the Pulley Guards CONNECTING MOTOR CORD TO SWITCH ASSEMBLY Disconnect the machine from the power sourceAttaching Blade to the SAW Table InsertStarting and stopping the saw Locking the switch in the off positionTilting the table Adjusting the table stop Adjusting blade tensionAdjusting Tightness of ANTI-DROP Screw Vertical Adjustment of the upper Blade guide assemblyTracking the blade Adjusting the upper blade guides and blade support bearing EnglishDust Port Adjusting lower blade guides and blade support bearingChanging Blade Speed for Model 28-206 only Troubleshooting Guide CUTTING CURVESProbable Cause Remedy Pointer out of adjustment Probable CauseRemedy Probable Cause RemedyBand SAW Blades Maintenance ServiceWarranty AccessoriesService and Repairs LES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsRègles DE Sécurité Générales Règles Spécifiques Additionnelles De Sûreté Conserver CES DirectivesRaccordements Électriques Spécifications DU MoteurInstructions DE Mise À LA Terre FrenchCordon DE Rallonge Fonctionnement Monophasé À 240 VoltsDescription Fonctionnelle Contenus DE BoiteAVANT-PROPOS Désemballage ET NettoyagePièces DU Socle Fermé DU Modèle Pièces DU Socle Ouvert DU Modèle Assemblage Outils Nécessaires Pour L’ASSEMBLAGEDurée Estimée Pour L’ASSEMBLAGE Assemblage DU Socle Fermé DU ModèleFrench Assemblage DU Socle Ouvert DU Modèle French Assemblage DE LA Scie SUR LE Socle Assemblage DES Protecteurs DE PoulieConnexion DU Cordon Moteur À L’ENSEMBLE DE L’INTERRUPTEUR Assemblage DE LA Table SUR LA ScieAssemblage DE LA Lame SUR LA Scie Insert DE TableFonctionnement Démarrage ET Arrêt DE ScieVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT Inclinaison DE LA TableRéglage DE LA Butée DE LA Table Réglage DE LA Tension DE LameAlignement DE LA Lame Ne jamais aligner la lame lorsque l’appareil fonctionneRéglage DU Serrage DE LA VIS DE Prévention DE Tombée Débrancher l’appareil de la source d’alimentation Goulotte À Poussière Coupe DE CourbesProblème LA Scie NE Démarre PAS Cause probable Solution Guide DE DépannageProblème LA Scie À Ruban Vibre Beaucoup Cause probable Problème LES Lames Cassent Cause probableLames DE Scie À Lame Ruban Problème LA Lame NE S’ALIGNE PAS Cause probableEntretien Accessoiries GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesNinguna aplicación de otra manera que para que se diseñó Normas Generales DE Seguridad Guarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación ESPECIFICACIONES DEL MOTORCordones DE Extensión Fig. D1Contenido DE Carton Descripción FuncionalPrologo Piezas Cerradas DEL Soporte DEL Modelo Base Tornillo de cabeza troncocónica M5 x 0.8 x 10 mm LadoPiezas Abiertas DEL Soporte DEL Modelo Ensamblaje Herramientas DE Ensamblaje RequeridasEstimación DEL Tiempo DE Ensamblaje Montaje DE LA Base DE Soporte Cerrada ModeloNota Apriete libremente el hardware para el ajuste adicional Montaje DE LA Base DE Soporte Abierta Modelo DA BPage Sujeción DE LA Sierra a LA Base DE Soporte Conectar LA Agujeros DEL Protector DE LA PoleaCuerda DEL Motor QUE Conecta a LA Asamblea DE Interruptor Sujeción DE LA Mesa a LA SierraSujeción DE LA Hoja a LA Sierra Montaje DE LA Pieza DE Insercion DE MesaOperación Arrancando Y Deteniendo LA SierraBloqueando EL Interruptor EN LA Posicion DE Apagado Inclinación de la tablaAjuste de la parada de la tabla Ajuste de la tensión de la láminaSeguir la lámina Ajuste Vertical del montaje superior de la guía de la láminaAjuste DE LA Tensión DEL Tornillo CON Bloqueo Reajustar Piezas CON Bloqueo CON Accesorios DE AlturaDesconecte la maquina de la fuente de energia Utilizar LA Maquina Puerto del polvoGuia Localizacion DE Fallas Corte DE CurvasCausa probable RemedioRemedios Hojas DE Sierra DE Cinta MantenimientoMantenga LA Máquina Limpia Servicio Falla EN EL EncendidoLubricación Y Protección Contra Óxido Mantenimiento Y ReparacionesIdentificación Delproducto AccesoriosExcepciones Garantia Para Otras LocalidadesGarantía limitada de dos años para productos nuevos
Top Page Image Contents