Conair UGR003/0800 manual Appendix GUARANTEE/WARRANTY

Page 64

EQUIPMENT GUARANTEE

PERFORMANCE WARRANTY

WARRANTY LIMITATIONS

Conair guarantees the machinery and equipment on this order, for a period as defined in the quotation from date of shipment, against defects in material and workmanship under the normal use and service for which it was recom- mended (except for parts that are typically replaced after normal usage, such as filters, liner plates, etc.). Conair’s guarantee is limited to repairing or replacing, at our option, the part or parts determined by us to be defective after examination. The customer assumes the cost of trans- portation of the part or parts to and from the factory.

Conair warrants that this equipment will perform at or above the ratings stated in specific quotations covering the equipment or as detailed in engineering specifications, provided the equipment is applied, installed, operated and maintained in the recommended manner as outlined in our quotation or specifications.

Should performance not meet warranted levels, Conair at its discretion will exercise one of the following options:

Inspect the equipment and perform alterations or adjustments to satisfy performance claims. (Charges for such inspections and corrections will be waived unless failure to meet warranty is due to misapplica- tion, improper installation, poor maintenance practices or improper operation.)

Replace the original equipment with other Conair equipment that will meet original performance claims at no extra cost to the customer.

Refund the invoiced cost to the customer. Credit is subject to prior notice by the customer at which time a Return Goods Authorization Number (RGA) will be issued by Conair’s Service Department. Returned equipment must be well crated and in proper operating condition, including all parts. Returns must be prepaid.

Purchaser must notify Conair in writing of any claim and provide a customer receipt and other evidence that a claim is being made.

Except for the Equipment Guarantee and Performance Warranty stated above, Conair disclaims all other war- ranties with respect to the equipment, express or implied, arising by operation of law, course of dealing, usage of trade or otherwise, including but not limited to the implied warranties of merchantability and fitness for a particular purpose.

A-2

APPENDIX

GUARANTEE/WARRANTY

UGR003/0900

Image 64
Contents UCR-150L Robot Date Document Number Table of Contents IntroductionMaintenance Introduction HOW the User Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description ROBOT? What isTypical Applications HOW Robot WorksRobot Features Wrist flip cylinderSpecifications Front view Side viewExtended strip stroke Optional EquipmentEnd-of-arm tooling Installation Unpacking the Boxes Remove all packing materialInstallation Preparing for Installation Preparing the Platen Mounting pattern for the UCR-150L RobotConnecting the Robot Positioning the RobotConnect the SPI connector cable into Check to see what the power output is fromPlug the hand-held control into the control Setting Gripper Position Tighten the adjustment screws on the blockOpen the mold Hold the main arm and loosen the arm height Set the gripper height to the sprueSetting Strip Positions Connecting AIR Pressure Adjusting Sprue Verification SwitchAdjusting the Speed Verifying Electrical Interface Verifying motion controls permissivesVerifying the Inputs Mold Full OpenManual Testing Press the Stop button Automatic TestingPress the Auto/Recycle button Page Operation Hand Control Features Before StartingStopping the Robot Starting the RobotEmergency Stopping Viewing Information GripsOperating Manually Starting Automatic Operation Choosing the Mold Press the Program buttonUse the Up and Down arrows Press the Enter buttonPress Stop button Programming Motion SequencePress Program button Use the Forward arrow Continue to move through the motionProgramming HOME, Grip Vacuum Positions Press the Function buttonUse the right arrow to choose the setting Choose the function and settings you wantPress the Stop button to continue Monitoring INPUT/OUTPUT InputsSetting Timer Values Enter the new timer valuePress the Time button Press the Forward buttonChoosing Timer Settings Timer Setting Description LCD DisplaysAdjusting Traverse Movement Answering AN Alarm Open the safety door and verify that there isRestarting Automatic Operation Use the Motion Control buttonsMaintenance Maintenance Features Maintenance Preventative Maintenance Schedule DailyMonthly Be sure the main power is disconnected Checking Electrical ConnectionsTroubleshooting Before Beginning Identifying Cause of a ProblemFEW Words of Caution Error Display Area of problem Symptom Possible cause Solution Robot Does not CycleSafety interlock is on. Check the output and wiring Mold is Not Working ProperlyARM is Not Working Properly Strip Motion Is not Working There is no Horizontal MotionGripper Does not Work Gripper does not workThere is no vac Air pressure is incor Uum Rect Before YOU WE’RE Here to Help HOW to Contact Customer ServiceFrom outside the United States, call Appendix GUARANTEE/WARRANTY Electrical Diagrams Solenoid and Limit Switch Wiring Relay and IMM Interface Solenoid Valves Page PARTS/DIAGRAMS PARTS/LISTS Ref. Part No Description Traverse Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-5 Valve IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-7 Valve Parts JSU6 Slide Base YSA10DC-50B Strip Cylinder U3-MA0-LS Main Arm Description Quantity Main Arm Slide Unit LM20UU Main Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-19 Wrist Flip TANSI6P Wrist Flip Cylinder IMR004/0800 UCR-150L Robot PARTS/DIAGRAMS P/D-23 Gripper Assembly D12 D9191 Assembly, Gripper, with LS-4 Gripper GXL-8F Controller HW-CB116B