Dukane iQ Series user manual Regulatory Agency Compliance, CE Marking

Page 67

Section 9 – Specifications

Regulatory Agency Compliance

FCC

The generator complies with the following Federal Communications Commission regulations.

The limits for FCC measurement procedure MP-5, “Methods of Measurement of Radio Noise Emissions from ISM Equipment”, pursuant to FCC Title 47 Part 18 for Ultrasonic Equipment.

CE Marking

This mark on your equipment certifies that it meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformité Europeéne (European Conformity). The generator complies with the following CE requirements.

T h e E M C D i r e c t i v e 2 0 0 4 / 1 0 8 / E C for Heavy Industrial —

EN 61000-6-4: 2001

EN 55011: 2003

EN 61000-6-2: 2001

EN61000–4–2

EN61000–4–3

EN61000–4–4

EN61000–4–5

EN61000–4–6

EN61000–4–8

EN61000–4–11

The Low Voltage Directive 2006/95/EC.

The Machine Directive 98/37/EC.

EN 60204-1: 2006

Safety of Machinery - Electrical Equip- ment of Machines Part 1: Specification for General Requirements.

Effective 12/29/09:

The Machinery Directive 2006/42/EC.

EN 60204: 2006

Safety of Machinery - Electrical Equipment of Machines Part 1: General Requirements.

CAUTION

DO NOT make any modifications to the generator or associated cables as the changes may result in violating one or more regulations under which this equip- ment is manufactured.

Dukane Manual Part No. 403-577-01

Page  61

Image 67
Contents User’s Manual Copyright Revision Revision HistorySummary Date This page intentionally left blank Contents This page intentionally left blank Introduction SectionThis page intentionally left blank Read This Manual First General User InformationDrawings and Tables Hand Probes Key FeaturesSystem Overview GeneratorHealth and Safety This page intentionally left blank Plastics Health Notice General ConsiderationsDomestic Power Grounding Electrical SafetyInternational Power Grounding Unpacking Placing RFI Grounding Connnecting Cables InstallationThis page intentionally left blank Placing UnpackingRFI Grounding AC Power Inlet Connecting Cables Quick Start Guide200/240 Volt Systems Power CordsUltrasound Output Pin 0V Output Common Pin 1 End of Weld AlarmPin 2 Any Fault Alarm System Outputs Optional ConnectionsControls This page intentionally left blank Front Panel Overview Power Switch/Circuit BreakerControl Keys System LCD Display Power Bar GraphArrow Keys + and KeysStarting a Weld Cycle Start-up SequenceStopping a Weld Cycle Manual Weld LCD Display OverviewSetup Maintenance Process Control SettingsThis page intentionally left blank Select the Welding Mode Process Controller SettingsTime key Navigate to Time ModeNavigating to Manual Mode Navigating Through the ModesKey Navigate to Energy ModeHold Amplitude AdjustmentHardware Settings System Information Hardware Settings, AdvancedSystem Information Free Run Frequency Advanced Settings40 % Introduction Setup MaintenanceNavigating Selecting a Setup Saving the Current SetupDeleting a Setup This page intentionally left blank Probes and Probe Stacks This page intentionally left blank Operating Notes Ultrasonic Probe OverviewCompressed Air Fitting In continuous duty Theory of Operation Ultrasonic Horn Attaching a Replaceable Tip to a Horn Stack AssemblyAttaching the Mounting Stud to a Horn or a Booster 5Stack Assembly Procedure In-lb Ft-lb KHz Stack Disassembly Removing the Mounting Stud from a Horn or Booster Booster Notes How to Tell the Booster Input End from the OutputTroubleshooting This page intentionally left blank No Ultrasonic Output System Power Output LevelWeak Welds Welding ProblemsInconsistent Welds Generator Fault Status Screens Manual Mode Pop-up Fault Status ScreensProcess Fault Status Screens Time and Energy Modes Options This page intentionally left blank IQ Hand Probe Options Foot Switch Kit Part NoBuzzer Kit Part No This page intentionally left blank Specifications This page intentionally left blank 1Generator Outline Drawing 2Probes Outline Drawings and Dimensions Operating Environment WeightsAC Power Requirements CE Marking Regulatory Agency ComplianceThis page intentionally left blank Outputs Interface This page intentionally left blank IQ Hand Probe Generator Rear Panel Detail This page intentionally left blank Contacting Dukane This page intentionally left blank Contacting Dukane Intelligent Assembly SolutionsIdentify Equipment This page intentionally left blank Appendices This page intentionally left blank Front Panel List of FiguresDescription List of TablesDukane ISO Part No - 577- 01