Dukane iQ Series user manual General User Information, Read This Manual First, Drawings and Tables

Page 9

Section 1 – Introduction

General User Information

Read This Manual First

Before operating your ultrasonic system, read this User’s Manual to become familiar with the equipment. This will ensure correct and safe operation. The manual is orga- nized to allow you to learn how to safely operate this gen- erator. The examples given are chosen for their simplicity to illustrate basic operation concepts.

Notes, Cautions and Warnings

Throughout this manual we use NOTES to provide in- formation that is important for the successful applica- tion and understanding of the product. A NOTE block is shown to the right.

In addition, we use special notices to make you aware of safety considerations. These are the CAUTION and WARNING blocks as shown here. They represent in- creasing levels of important information. These state- ments help you to identify and avoid hazards and rec- ognize the consequences. One of three different symbols also accompany the CAUTION and WARNING blocks to indicate whether the notice pertains to a condition or practice, an electrical safety issue or a operator protection issue.

Drawings and Tables

The figures and tables are identified by the section num- ber followed by a sequence number. The sequence num- ber begins with one in each section. The figures and tables are numbered separately. The figures use Arabic sequence numbers (e.g. –1, –2, –3) while the tables use roman sequence numerals (e.g. –I, –II, –III). As an ex- ample, Figure 3–2 would be the second illustration in section three while Table 3–II would be the second table in section three.

NOTE

Note statements provide additional information or highlight procedures.

CAUTION

C a u t i o n s t a t e m e n t s identify conditions or practices that could result in damage to the equip- ment or other property.

WARNING

Warning statements point out conditions or practices that could re- sult in personal injury or loss of life.

 

Condition

Electrical

Hearing

or Practice

Hazard

Protection

Dukane Manual Part No. 403-577-01

Page 

Image 9
Contents User’s Manual Copyright Revision History RevisionSummary Date This page intentionally left blank Contents This page intentionally left blank Introduction SectionThis page intentionally left blank General User Information Read This Manual FirstDrawings and Tables System Overview Key FeaturesGenerator Hand ProbesHealth and Safety This page intentionally left blank Plastics Health Notice General ConsiderationsElectrical Safety Domestic Power GroundingInternational Power Grounding Unpacking Placing RFI Grounding Connnecting Cables InstallationThis page intentionally left blank Unpacking PlacingRFI Grounding AC Power Inlet Connecting Cables Quick Start GuidePower Cords 200/240 Volt SystemsUltrasound Output Pin 2 Any Fault Alarm Pin 1 End of Weld AlarmSystem Outputs Optional Connections Pin 0V Output CommonControls This page intentionally left blank Power Switch/Circuit Breaker Front Panel OverviewControl Keys Arrow Keys Power Bar Graph+ and Keys System LCD DisplayStart-up Sequence Starting a Weld CycleStopping a Weld Cycle Manual Weld LCD Display OverviewSetup Maintenance Process Control SettingsThis page intentionally left blank Select the Welding Mode Process Controller SettingsNavigating to Manual Mode Navigate to Time ModeNavigating Through the Modes Time keyKey Navigate to Energy ModeHold Amplitude AdjustmentSystem Information Hardware Settings, Advanced Hardware SettingsSystem Information Free Run Frequency Advanced Settings40 % Setup Maintenance IntroductionNavigating Saving the Current Setup Selecting a SetupDeleting a Setup This page intentionally left blank Probes and Probe Stacks This page intentionally left blank Ultrasonic Probe Overview Operating NotesCompressed Air Fitting In continuous duty Theory of Operation Ultrasonic Horn Attaching a Replaceable Tip to a Horn Stack AssemblyAttaching the Mounting Stud to a Horn or a Booster 5Stack Assembly Procedure In-lb Ft-lb KHz Stack Disassembly Removing the Mounting Stud from a Horn or Booster Booster Notes How to Tell the Booster Input End from the OutputTroubleshooting This page intentionally left blank No Ultrasonic Output System Power Output LevelWelding Problems Weak WeldsInconsistent Welds Generator Fault Status Screens Manual Mode Pop-up Fault Status ScreensProcess Fault Status Screens Time and Energy Modes Options This page intentionally left blank Foot Switch Kit Part No IQ Hand Probe OptionsBuzzer Kit Part No This page intentionally left blank Specifications This page intentionally left blank 1Generator Outline Drawing 2Probes Outline Drawings and Dimensions Operating Environment WeightsAC Power Requirements CE Marking Regulatory Agency ComplianceThis page intentionally left blank Outputs Interface This page intentionally left blank IQ Hand Probe Generator Rear Panel Detail This page intentionally left blank Contacting Dukane This page intentionally left blank Intelligent Assembly Solutions Contacting DukaneIdentify Equipment This page intentionally left blank Appendices This page intentionally left blank Front Panel List of FiguresDescription List of TablesDukane ISO Part No - 577- 01