DeWalt DW708 Additional Safety Rules for Sliding Compound Miter Saw, Double Insulation, Awg

Page 4

English

Important Safety Instructions for all Tools

WARNING: For your own safety, read the instruction manual before operating the sliding compound miter saw. Failure to heed these warnings may result in personal injury and serious damage to the saw. When servicing this tool, use only identical replacement parts. Have damaged cords replaced by an authorized service center.

DOUBLE INSULATION

Double insulated tools are constructed throughout with two separate layers of electrical insulation or one double thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords.

POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following:

KEEP GUARDS IN PLACE and in working order.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain or snow. Keep work area well lighted.

KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.

MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

 

 

Minimum Gage for Cord Sets

 

 

Volts

 

 

Total Length of Cord in Feet

120V

 

0-25

26-50

51-100

101-150

Ampere Rating

 

AWG

 

 

More

Not more

 

 

 

Than

Than

 

 

 

 

 

12 -

16

14

12

Not Recommended

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. Air vents often cover moving parts and should also be avoided.

ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.

SECURE WORK. Use clamps or vise when you cannot secure the workpiece on the table and against the fence by hand or when your hand will be dangerously close to the blade (within 6”)

DON’T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

DISCONNECT TOOLS before servicing; when changing accessories, such as blades, clamps, extensions, and the like.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function–check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

REPLACEMENT PARTS. When servicing, use only identical replacement parts.

Additional Safety Rules for Sliding Compound Miter Saw

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. .

Keep hands out of path of saw blade. NEVER CUT A PIECE WHERE HAND WOULD BE 6" (152 mm) OR LESS FROM BLADE.

Do not operate saw without guards in place.

Do not perform any operation freehand, that is without holding or clamping the workpiece against the fence and saw blade.

Never reach in back of the saw blade.

Turn off the tool and wait for saw blade to stop before moving the workpiece or changing settings.

Disconnect power before changing the blade or servicing.

Blade adjustment is to be made only with the power off and the blade stopped.

Never use the saw without the kerf plate.

Replace the kerf plate when it is worn.

To reduce risk of injury, return the carriage to the full rear position after each crosscut operation.

DO-Protect electric supply line with at least a 15 ampere time-delay fuse or a circuit breaker.

DO-Make certain the blade rotates in the correct direction and that the teeth at the bottom of the blade are pointing to the rear of the sliding compound miter saw.

DO use stabilizer bar at all times.

DO-Be sure all clamp handles and knobs are tight before starting any operation.

DO-Be sure all blade and clamp washers are clean and recessed sides of collars are against blade. Tighten arbor screw securely.

DO- Keep the saw blade sharp and properly aligned.

DO-Keep the motor air slots free of chips and dirt.

DO-Use the blade guard at all times.

2

Image 4
Contents Dewalt English DEWALT… Built Jobsite ToughTable of Contents Additional Safety Rules for Sliding Compound Miter Saw Double InsulationPolarized Plugs Ampere RatingOn Base On Stabilizer Electrical Connection Unpacking Your SawFamiliarization ControlsSpecifications Optional Attachments/AccessoriesAdjustments StabilizerBench Mounting Transporting the SawAdjusting the bevel stop to 45 left or right Fence AdjustmentScrew Miter LOCK/DETENT ROD ˚ Bevel Stop Screw Left Bevel StopOperation Quality of Cut Body and Hand Position FigureClamping the Workpiece Support for Long PiecesMaking Fine Adjustments When Mitering to the Right Making Fine Adjustments When Mitering to the LeftDual Range Miter Scale Vernier ScaleTo CUT AN Outside Corner Joint To CUT AN Outside CornerCutting Molding Returns Cutting Crown MoldingSpecial Cuts To CUT AN Inside Corner JointAluminum Cutting Bowed MaterialGraph of Common Compound Miter Cuts Installing a New Saw Blade SettingGrooving Removing the BladeMaintenance Three Year Limited WarrantyRemoving and Replacing Belt RepairsBe Sure to Follow Safety Rules and Instructions Trouble Shooting GuideWHAT’S WRONG? What to DO… Table DES Matieres OutilsEntretien Réparations Garantie Guide DE DépannageDouble Isolation Fiches PolariséesCalibre minimal des cordons de rallonge Tension Longueur totale du cordon en metersSUR LE Guide Mobile Raccordement électrique Déballage de la scieFamiliarisation RéglagesAccessoires en option CaractéristiquesMontage sur l’établi Stabilisateur de baseTransport de la scie Réglage DE L’INDICATEUR D’ONGLET Bouton DE Réglage DU GuideActivation et visibilité du protège-lame Frein électrique automatiqueBalais FonctionnementInterrupteur à gâchette Couper avec votre scieQualité de la coupe Fixation de la pièceSoutien des longues pièces Coupe EN BiseauCoupe de précision Réglage DU Type DE Coupe Biseau Pour Couper UN Joint DE Coin IntérieurTableau 1 Coupe EN Onglets Mixtes Régler LA Scie À CET Angle DE BiseauPour Couper UN Joint DE Coin Extérieur Coupe d’une plinthe à plat par biseautagePour Couper LES Pièces DE Finition Coupe DES Moulures DE CouronnementInstallation d’une nouvelle lame de scie Coupes particulièresPieces Courbées RainurageRéparations EntretienGarantie limitée de trois ans Guide de dépannage DEWALT...PARA Trabajos Pesados DewaltContenido Instrucciones DE Seguridad Para Toda HerramientaDoble Aislamiento Instrucciones importantes de seguridadEnchufes Polarizados Español Conexión eléctrica Como desempacar la sierraConocimiento de la herramienta ControlesEspecificaciones Accesorios opcionalesEstabilizador Montaje del bancoComo transportar la sierra RegulacionesRegulación DEL Seguro DE Ingletes EspañolFuncionamiento Cortes transversales Calidad del cortePosición del cuerpo y las manos Figura Hierro O Acero NI Material DE MamposteríaComo fijar la pieza de trabajo Soporte de piezas largasCortes de precisión Posicion Tipo DE Corte DE BiselCorte DE Molduras Y Otros Marcos Escala DE Ingletes DE Doble RangoEscala DE Nonio Corte DE Molduras DE BaseCorte Exterior DE UNA Esquina Corte DE Vueltas Para MoldurasCortes DE Ingletes Compuestos Cortes particulares Como instalar una hoja nueva MantenimientoRemocion DE LA Hoja Instalacion DE LA HojaPóliza de Garantía ReparacionesGarantía limitada por tres años Diagnóstico de falla Asegurese DE Seguir LAS Reglas E Instrucciones DE Seguridad
Related manuals
Manual 21 pages 13.67 Kb