Bosch Power Tools 4100DG manual Using The Miter Gauge, Miter Gauge Auxiliary Facing, Example

Page 64

Using The Miter Gauge

CROSSCUTTING, MITER CUTTING, BEVEL CUTTING, COM- POUND MITER CUTTING and when RABBETING across the end of a narrow workpiece, the MITER GAUGE is used.

	!	WARNING	For your own safety, always observe the following
			safety precautions in addition to the safety

instructions on Pages 2, 3, 4 & 5.

Never make these cuts freehand (without using the miter gauge or other auxiliary devices) because the blade could bind in the cut and cause a KICKBACK or cause your fingers or hand to slip into the blade.

Always lock the miter gauge securely when in use.

Remove rip fence from table during any operations which utilize the miter gauge.

The miter includes a “T” groove disk 1 for easy insertion into table groove and quicker removal from the table (Fig 54).

When cross cutting and the blade set at 90º or 45º to the table, the miter gauge can be used in either slot on the table. When cross cutting and the blade is tilted, use slot on right side of table where the blade is tilted away from your hands and miter gauge.

To adjust the miter angle:

Loosen lock knob 1 and set the miter gauge body 2 so the pointer 3 is at desired angle, then tighten lock knob 1 (Fig. 54).

The miter gauge body 2 will stop at 90º and both right and left 45º. To rotate the miter gauge body 2 beyond these points, the stop plate 4 must be flipped out of the way.

Miter Gauge Auxiliary Facing

A template for drilling holes in the miter gauge is provided on page 84, which allows you to attach an AUXILIARY FACING 5 to provide additional support to cut longer pieces. Select a suitable piece of smooth straight wood, drill two holes through it and attach it with screws 6 (Fig. 55).

Example:

A. Drill 1/4" dia. holes thru miter gauge.

B. Drill 5/32" dia. holes thru (board 3/4" thick, 3" high, and desired length).

C. Attach with two No. 12 round head wood screws 1-1/2" long, 6, not included (Fig. 55).

Be sure screws never protrude above outside surface of facing.

Be sure facing does not interfere with the proper operation of the saw blade guard.

NOTE: When bevel crosscutting, attach facing so that it extends to the right of the miter gauge and use the miter gauge in the groove to the right of the blade.

FIG. 54

12

3

4

FIG. 55

6

5

64.

Image 64

Contents 4100 4100DG General Safety Rules Personal SafetyWork Area Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Think Safety When SERVICING, USE only Identical ReplaceDouble Insulated Tools Extension CordsTable of Contents Tools Needed For Assembly Glossary of TermsConsignes générales de sécurité Zone de travailSécurité de l’utilisateur Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFigurant À L’AVANT DE Votre Scie DE Table FAMILIARISEZ-VOUS Avec VOS Outils DE CoupeDouble isolation RallongesLA Sécurité Avant Tout IdentiquesTable des matières Lexique Outils nécessaires à l’assemblageNormas generales de seguridad Area de trabajoSeguridad personal Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Herramientas con aislamiento doble Cordones de extensiónPiense EN LA Seguridad Unicamente Piezas DE Repuesto IdenticasIndice PáginaGlosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw 13 1 4Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaSmart Guard System Smart Guard System StorageTable Insert Digital Carriage Model 4100DG-09 onlySystème Smart Guard Rangement DU Système Smart Guard21. Élément Amovible DE LA Table DE Coupe Chariot Numérique Modèle 4100DG-09 SeulementUnpacking and Checking Contents Ouverture de l’emballage et Vérification du contenu Desempaquetado yListe des pièces fournies Tabla de piezas sueltasAttaching the Smart Guard System Positioning the Riving KnifeAssemblageEnsamblaje Montage du système Smart GuardPositionnement DU Couteau Diviseur Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SecuriteInstalación DEL Dispositivo Antirretroceso Changing The Blade AssemblyTo prevent personal injury, always disconnect Cambio de la hoja Changement de la lameCambiar las hojas Mounting Table Saw Attaching Rip FenceInstallation de la scie De table Montaje de la sierra de MesaMontage du guide de refente Colocación del tope-guía Para cortar al hiloAdjustments Adjusting 0 Degree Positive StopsAdjusting 0 Degree Positive Stop Adjusting 45 Degree Positive StopRéglage des butées fixes 90 et RéglagesAjustesAjuste de los topes positivos De 90 y 45 grados Adjusting Blade Parallel To Miter Gauge Slots Miter Gauge AdjustmentAjuste del calibre de ingletes Realizar cualquier ajusteAligning Rip Fence Rip Fence Pointer AdjustmentTo set the rip fence pointer Alignement du guide de refente RefenteAlineación del tope-guía para Cortar al hilo Ajuste del indicador del tope-guía paraTable Pointer Adjustment Adjusting The Table InsertRéglage de l’indicateur de la table Ajuste del indicador de la mesaRéglage de lélément rapporté De la table Ajuste del accesorio de inserción De la mesaRiving Knife Alignment Adjusting Riving KnifeChecking Riving Knife Alignment Alignement du Couteau Diviseur Alineación de la Cuchilla SeparadoraSafety Power Switch Basic Table Saw OperationSmart Guard System ❶Component Parts figureFuncionamiento básico de La sierra de mesa Interrupteur de sûretéSystème Smart Guard Interruptor de encendido De seguridadExtending Table Extension Blade Bevel ControlSystem Storage Réglage de l’inclinaison de la lame Réglage de la rallonge de tableControl de inclinación de la hoja Ajuste de la extensión de la mesaInstalling 9 Volt Battery Features see figures 37Bosch Digital Carriage Model DC010Chariot numérique Bosch Carro digital BoschReset button see figures 39 Control Buttons and DisplayON/OFF Button and Memory see figure Automatic Shut OffBotones de control y pantalla Zero Out the Display see figures 40 Display Changes RightDisplay Changes Left To Zero OutCambios en la pantalla, a la derecha del Cambios en la pantalla, a la izquierda delRemise à zéro de lécran daffichage Voir Figures 40 Changements de laffichage Droite de « 0 »Connecting Digital Carriage To Rip Fence Connexion du chariot numérique Au guide de refente Conexión del carro digital al tope-guía Para cortar al hiloSetting Fence with Digital Carriage Right Side Rip Cuts 0 to 13-1/2 figExtended Right Side Rip Cuts 13-1/2 to 25 fig Left Side Rip Cuts figAjuste del tope-guía con el carro digital Coupes longitudinales du côté droit de 0 po à 13 1/2 po FigCoupes longitudinales du côté gauche Fig Cortes al hilo en el lado derecho de 0 a 13-1/2 figCleaning Maintaining the Digital CarriageBevel Rip Cuts Right side only Parking Position see figureEntretien du chariot numérique Mantenimiento del carro digitalUsing The Rip Fence Pointer When Table Is Not Extended Using The Table Pointer When Table Is ExtendedPre-Cut Locator Making Rip Cuts Beyond Inches Without The Use Of ScaleUbicador de precorte Repère de sciageSans utiliser d’échelle graduée Make the Push Stick 1 using a piece of 1 x 2 as shown Fig Work HelpersPush Stick and Push Block Auxiliary FenceAccessoires de sciage Guide de coupe auxiliaireAyudantes de trabajo Palo de empujar y bloque de empujarUsing The Miter Gauge To adjust the miter angleSafety precautions in addition to the safety Miter Gauge Auxiliary FacingUtilización del calibre de ingletes Guide de coupe angulaireCalibre de ingletes Réglage du guide de coupe angulaireCrosscutting Corte transversal Coupe transversaleOtra Razon Assembly Repetitive CrosscuttingMaking the Facing Block Parts RequiredCoupe transversale répétitive Realización DEL Corte Transversal RepetitivoUsing the Rip Fence Miter CuttingBevel Crosscutting Compound Miter CuttingCoupe angulaire Coupe transversale biseautéeCoupe angulaire biseautée Utilisation du guide de refenteDIA Hole RIP Fence Auxiliary FacingPièce Dappoint Auxiliaire Pour LE Guide DE Refente Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte AL Hilo EN Bisel Rabbeting Non Thru-SawingDadoing and Molding Coupe partielle Aserrado no pasanteRéalisation de feuillures Rainures et mouluresMaintenance Maintaining Your Table SawSpecial Cutting Techniques Cutting Metals and MasonryEntretien de la scie de table Mantenimiento de la sierra De mesaRecommended Accessories Use only recommended accessories. FollowImproper accessories may cause hazards LubricationAccessoires recommandés Accesorios recomendados LubrificationLubricación ArticleTrouble Shooting Guide de diagnosticLocalización y reparación De averías Averia LA Sierra no ArrancaFollow Steps Suivez LES Étapes Siga LOS Pasos Comme indiqué ci-dessus, et fixez-le avec du ruban adhésifPage Page Page Limited Warranty of Bosch Portable and Benchtop Power Tools