Bosch Power Tools 4100DG manual Non Thru-Sawing, Rabbeting, Dadoing and Molding

Page 76

Non Thru-Sawing

Add 8" high flat facing board to the fence, the full length of the fence (Fig. 66).

Use featherboards for all “Non Thru-Sawing” operations (when

 

 

sawblade guard must be removed). Featherboards 1 are used to

 

 

FIG. 66

keep the work in contact with the fence and table as shown, and to

 

WORK

stop kickbacks.

 

 

 

SUPPORT

“C” CLAMPS

SERRE-JOINTS EN C

1

Mount featherboards 1 to fence and table as shown, so that leading edges of featherboards will support workpiece until cut is complete, and the workpiece has been pushed completely past the cutter (sawblade, dado head, molding head, etc.) with a Push Stick 2, as in ripping.

Before starting the operation (switch saw “OFF” and set cutter below table surface):

A. Install featherboards so they exert pressure on the workpiece;

BE POSITIVE THEY ARE SECURELY ATTACHED.

B. Make sure by trial that the featherboards will stop a kickback if one should occur.

Featherboards are not employed during non thru-sawing operations when using the miter gauge.

REPLACE THE SMART GUARD SYSTEM AS SOON AS THE NON THRU-SAWING OPERATION IS COMPLETE.

Rabbeting

SUPPORT

APOYO DE LA

PIEZA DE

TRABAJO

ABRAZADERAS EN “C”

2

1

RABBETING is known as cutting out a section of the corner of a piece of material, across an end or along an edge (Fig. 67).

Making a RABBET requires cuts which do not go all the way through the material. Therefore the Smart Guard System must be removed.

1. Remove blade guard.

FIRST CUT

2. For rabbeting along an edge (long way of workpiece) as shown,

add facing to rip fence approximately as high as the workpiece is

wide. Adjust rip fence and blade to required dimensions; then make

FIG. 67

PREMIÈRE COUPE

PRIMER CORTE

first cut with board flat on table, follow set-up Fig. 66. Make second

cut with workpiece on edge. Follow all precautions, safety

instructions, and operation instructions as for ripping or rip type

operations, including featherboards and Push Stick, etc.

3. For rabbeting across an end, for workpiece 10-1/2" and narrower

make the rabbet cut with the board flat on the table. Using the miter

gauge fitted with a facing, follow the same procedures and

instructions for crosscutting making successive cuts across the

width of the workpiece to obtain the desired width of cut. DO NOT

use the rip fence for rabbeting across the end.

4. INSTALL SMART GUARD SYSTEM IMMEDIATELY UPON

COMPLETION OF RABBETING OPERATION.

Rabbet cuts can also be made in one pass of the workpiece over the cutter using the dado head or molding head.

RABBET

FEUILLURE

REBAJO

SECOND CUT

 

DEUXIÈME COUPE

 

SEGUNDO CORTE

 

RABBETING ALONG

RABBETING ACROSS

THE EDGE

THE END

RÉALISATION D’UNE

RÉALISATION D’UNE

FEUILLURE LE LONG D’UN

FEUILLURE EN TRAVERS

BORD

D’UNE EXTRÉMITÉ

Dadoing and Molding

Instructions for operating the Dado and Molding Heads are contained in the booklet furnished with these accessories.

ALWAYS USE APPROPRIATE TABLE INSERT LISTED UNDER ACCESSORIES.

REBAJO A LO LARGO

REBAJO TRANSVERSAL

DEL BORDE

AL EXTREMO

76.

Page 75 Page 77
Image 76
Page 75 Page 77
Contents 4100 4100DG General Safety Rules Personal SafetyWork Area Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Think Safety When SERVICING, USE only Identical ReplaceDouble Insulated Tools Extension CordsTable of Contents Tools Needed For Assembly Glossary of TermsConsignes générales de sécurité Zone de travailSécurité de l’utilisateur Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFigurant À L’AVANT DE Votre Scie DE Table FAMILIARISEZ-VOUS Avec VOS Outils DE CoupeDouble isolation RallongesLA Sécurité Avant Tout IdentiquesTable des matières Lexique Outils nécessaires à l’assemblageNormas generales de seguridad Area de trabajoSeguridad personal Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Herramientas con aislamiento doble Cordones de extensiónPiense EN LA Seguridad Unicamente Piezas DE Repuesto IdenticasIndice PáginaGlosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw 13 1 4Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaSmart Guard System Smart Guard System StorageTable Insert Digital Carriage Model 4100DG-09 onlySystème Smart Guard Rangement DU Système Smart Guard21. Élément Amovible DE LA Table DE Coupe Chariot Numérique Modèle 4100DG-09 SeulementUnpacking and Checking Contents Ouverture de l’emballage et Vérification du contenu Desempaquetado yListe des pièces fournies Tabla de piezas sueltasAttaching the Smart Guard System Positioning the Riving KnifeAssemblageEnsamblaje Montage du système Smart GuardPositionnement DU Couteau Diviseur Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SecuriteInstalación DEL Dispositivo Antirretroceso Changing The Blade AssemblyTo prevent personal injury, always disconnect Cambio de la hoja Changement de la lameCambiar las hojas Mounting Table Saw Attaching Rip FenceInstallation de la scie De table Montaje de la sierra de MesaMontage du guide de refente Colocación del tope-guía Para cortar al hiloAdjustments Adjusting 0 Degree Positive StopsAdjusting 0 Degree Positive Stop Adjusting 45 Degree Positive StopRéglage des butées fixes 90 et RéglagesAjustesAjuste de los topes positivos De 90 y 45 grados Adjusting Blade Parallel To Miter Gauge Slots Miter Gauge AdjustmentAjuste del calibre de ingletes Realizar cualquier ajusteAligning Rip Fence Rip Fence Pointer AdjustmentTo set the rip fence pointer Alignement du guide de refente RefenteAlineación del tope-guía para Cortar al hilo Ajuste del indicador del tope-guía paraTable Pointer Adjustment Adjusting The Table InsertRéglage de l’indicateur de la table Ajuste del indicador de la mesaRéglage de lélément rapporté De la table Ajuste del accesorio de inserción De la mesaRiving Knife Alignment Adjusting Riving KnifeChecking Riving Knife Alignment Alignement du Couteau Diviseur Alineación de la Cuchilla SeparadoraSafety Power Switch Basic Table Saw OperationSmart Guard System ❶Component Parts figureFuncionamiento básico de La sierra de mesa Interrupteur de sûretéSystème Smart Guard Interruptor de encendido De seguridadExtending Table Extension Blade Bevel ControlSystem Storage Réglage de l’inclinaison de la lame Réglage de la rallonge de tableControl de inclinación de la hoja Ajuste de la extensión de la mesaInstalling 9 Volt Battery Features see figures 37Bosch Digital Carriage Model DC010Chariot numérique Bosch Carro digital BoschReset button see figures 39 Control Buttons and DisplayON/OFF Button and Memory see figure Automatic Shut OffBotones de control y pantalla Zero Out the Display see figures 40 Display Changes RightDisplay Changes Left To Zero OutCambios en la pantalla, a la derecha del Cambios en la pantalla, a la izquierda delRemise à zéro de lécran daffichage Voir Figures 40 Changements de laffichage Droite de « 0 »Connecting Digital Carriage To Rip Fence Connexion du chariot numérique Au guide de refente Conexión del carro digital al tope-guía Para cortar al hiloSetting Fence with Digital Carriage Right Side Rip Cuts 0 to 13-1/2 figExtended Right Side Rip Cuts 13-1/2 to 25 fig Left Side Rip Cuts figAjuste del tope-guía con el carro digital Coupes longitudinales du côté droit de 0 po à 13 1/2 po FigCoupes longitudinales du côté gauche Fig Cortes al hilo en el lado derecho de 0 a 13-1/2 figCleaning Maintaining the Digital CarriageBevel Rip Cuts Right side only Parking Position see figureEntretien du chariot numérique Mantenimiento del carro digitalUsing The Rip Fence Pointer When Table Is Not Extended Using The Table Pointer When Table Is ExtendedPre-Cut Locator Making Rip Cuts Beyond Inches Without The Use Of ScaleUbicador de precorte Repère de sciageSans utiliser d’échelle graduée Make the Push Stick 1 using a piece of 1 x 2 as shown Fig Work HelpersPush Stick and Push Block Auxiliary FenceAccessoires de sciage Guide de coupe auxiliaireAyudantes de trabajo Palo de empujar y bloque de empujarUsing The Miter Gauge To adjust the miter angleSafety precautions in addition to the safety Miter Gauge Auxiliary FacingUtilización del calibre de ingletes Guide de coupe angulaireCalibre de ingletes Réglage du guide de coupe angulaireCrosscutting Corte transversal Coupe transversaleOtra Razon Assembly Repetitive CrosscuttingMaking the Facing Block Parts RequiredCoupe transversale répétitive Realización DEL Corte Transversal RepetitivoUsing the Rip Fence Miter CuttingBevel Crosscutting Compound Miter CuttingCoupe angulaire Coupe transversale biseautéeCoupe angulaire biseautée Utilisation du guide de refenteDIA Hole RIP Fence Auxiliary FacingPièce Dappoint Auxiliaire Pour LE Guide DE Refente Refrentado Auxiliar Para EL TOPE-GUÍA Para Cortar AL HiloRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte AL Hilo EN Bisel Rabbeting Non Thru-SawingDadoing and Molding Coupe partielle Aserrado no pasanteRéalisation de feuillures Rainures et mouluresMaintenance Maintaining Your Table SawSpecial Cutting Techniques Cutting Metals and MasonryEntretien de la scie de table Mantenimiento de la sierra De mesaRecommended Accessories Use only recommended accessories. FollowImproper accessories may cause hazards LubricationAccessoires recommandés Accesorios recomendados LubrificationLubricación ArticleTrouble Shooting Guide de diagnosticLocalización y reparación De averías Averia LA Sierra no ArrancaFollow Steps Suivez LES Étapes Siga LOS Pasos Comme indiqué ci-dessus, et fixez-le avec du ruban adhésifPage Page Page Limited Warranty of Bosch Portable and Benchtop Power Tools
Top Page Image Contents