Ryobi P541 manuel dutilisation General Maintenance

Page 22

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during power product operation or when blowing dust. If operation is dusty, also wear a dust mask.

WARNING:

Toavoidseriouspersonalinjury,alwaysremovethe battery pack from the product when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Before each use, inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please call 1-800-860-4050 or contact an authorized service center for assistance.

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an Authorized Service Center.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

WARNING:

Upon removal, cover the battery pack’s ter- minals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

16 - English

Image 22
Contents Accepts ALL one+ Battery Packs Save this Manual for Future ReferenceSAFE-T-TIP Chain Line Ligne de chaîne Plano de la cadena Wedge coin, cuña Kickback rebond, contragolpe CELUI-CI Soit Débité Angle D’AFFÛTAGE DE LA Plaque Supérieure Correct Lockingwasherrondelledeverrouillage, arandela de fijación Introduction Read ALL Instructions Basic Safety Precautions Safety ApparelKickback Cutting/Work AreaGuide Bars Understanding Your Chain Saw Safety DevicesLow Kickback Saw Chain SAFE-T-TIPAnti-Kickback Nose GuardSpecific Safety Rules Battery SafetySymbols Symbol Signal Meaning ServiceProduct Specifications FeaturesAssembly UnpackingOperation To Install / Remove Battery PackTo install ApplicationsStarting and Stopping the Chain SAW Chain Oil SystemPreparation for Cutting Proper Grip on Handles Starting the chain sawProper Cutting Stance Basic Cutting ProcedureWork Area Precautions Tree FellingOperation Types of Cutting Used BuckingBucking Logs Under Stress LimbingPruning SpringpolesMaintenance General MaintenanceChain Tension REPLACing Bar and ChainRecommended Bar and Chain Combinations Bar Part Number 10Chain Maintenance How to Sharpen the CuttersSide Plate Angle Guide BAR MaintenanceTop Plate Filing Angle Depth Gauge ClearanceMounting SAFE-T-TIPNose Guard SAFE-T-TIPNose Guard MaintenanceTransporting and Storing Troubleshooting Problem Cause SolutionWarranty Limited Warranty StatementRègles DE Sécurité Générales AVERTISSEMENT Dans la zone de coupe/travail Vêtements DE SécuritéRebond Voir les figures 1 àGuides Garde antirebond SAFE-T-TIPChaîne à rebond réduit Voir la figureSécurité Batterie Symboles SAFE-T-TIPSymbole Signal Signification DépannageCaractéristiques AssemblageAvertissement RETRAIT/INSTALLATION DU Bloc- piles Installation RetraitArrêt de la scie à chaîne Précautions de chantier Position de coupe correcteMéthode de coupe élémentaire Abattage d’arbresUtilisation Types de coupe utilisés DébitageDébitage DE Billes Sous Contrainte Voir les figures 17 àFouets ÉbranchageÉlagage Coupe par le dessousEntretien Général EntretienRetrait ET Préparation DU Batteries Pour LE Recyclage Avertissement  Remplacement DU Guide ET DE LA ChaîneCombinaisons de guide et chaîne recommandées Voir les figures 24 àComment affûter les dents Voir les figures 33 etDégagement de jauge de profondeur Angle d’affûtage de la plaque supérieureEntretien DU Guide Entretien de la garde antirebond SAFE-T-TIP Installation de la garde antirebond SAFE-T-TIPInversion du guide Transport ET RemisageDépannage Problème Cause SolutionVoir Assemblage du guide et Garantie Énoncé DE LA Garantie LimitéeLEA Todas LAS Instrucciones Reglas DE Seguridad GeneralesAdvertencia Precauciones básicas de seguridadEn el área de corte o de trabajo ContragolpeVea las figuras 1 y Vea la figura Cadena de sierra de contragolpe moderadoBarras guía Protección anticontragolpe SAFE-T-TIPde la puntaReglas DE Seguridad Específicas Seguridad EN EL USO DEL Paquete DE PilasSímbolos Servicio Símbolo Señal Significado PeligroCausará la muerte o lesiones serias Características ArmadoAplicaciones FuncionamientoPara Desmontar Y Montar EL Paquete DE baterías PrecauciónPreparación para el corte Sujeción correcta de los mangos Sistema de lubricación de la cadenaEncendido Y Apagado DE LA Motosierra Vea las figuras 9 aPrecauciones en el área de trabajo Postura correcta para el corteProcedimiento básico de corte Tala de árbolesPeligro Las figuras 14 y TronzadoTronzado de troncos bajo tensión Vea las figuras 17 a laPoda Tipos de corte efectuadosDesramado PértigasMantenimiento Mantenimiento GeneralCombinaciones de barra y cadena recomendadas Reemplazo de la barra y de la cadenaAdvertencia Vea las figuras 24 a laMantenimiento de la cadena Tensión de la cadenaForma de afilar los dientes de corte Espacio libre del calibre de profundidad Ángulo de limadura de la placa superiorÁngulo de la placa lateral Mantenimiento DE LA Barra GuíaMontaje de la protección SAFE- T-TIPde la punta Inversión de la barra guíaMantenimiento de la protección Transporte Y AlmacenamientoCorreCIÓN DE Problemas Problema Causa SoluciónGarantía Declaración DE LA Garantía LimitadaPage Techtronic Industries North AMERICA, INC P541