Delta 37-071 instruction manual Feeding Stock, Jointing Beveled Stock, Outward 45 Angle

Page 13

OPERATION

FEEDING STOCK

1.Place the surface to be jointed face down on the infeed table and against the fence. Turn the jointer on and wait for the motor to come to full speed.

2.Apply light downward pressure and slowly feed the stock through the spring-loaded cutter guard and over the cutting head.

IMPORTANT: When feeding stock horizontally, with the width of the board laying flat against the table, always use safety paddles or a push stick, as shown in Figure 13. When feeding stock vertically, with the

width of the board flush against the fence, always keep fingers on top of the board. See Figure 14.

3.Keep moving the board until it clears the cutter.

4.Turn the jointer off and wait for the cutterhead to come to a stop before removing the stock.

FIGURE 13

FIGURE 14

JOINTING BEVELED STOCK

Disconnect the machine from the power source before making any

adjustments!

The fence can adjust to an inward 45° angle and an outward 45° angle, enabling you to joint beveled stock. To adjust the fence tilt, do the following:

OUTWARD 45° ANGLE:

See Figure 15.

1.Loosen the beveling lock by rotating the handle (A) counterclockwise.

2.Pull the spring-loaded pin (B) up and pull the 45°/90° Stop (C) back slightly.

3.Release the spring-loaded pin and continue pulling the 45°/90° Stop until it locks in position.

4.Retighten the beveling lock. Use a combination square or carpenters square to check the tilt angle. If it needs to be adjusted, refer to “Calibrating the 45°/90° Stops” on page 14.

FIGURE 15

13

Image 13
Contents IN. Bench Jointer Important Safety Instructions Table of ContentsGeneral Safety Rules Safety Guidelines DefinitionsAdditional Specific Safety Rules Additional Specific Safety Rules Motor Specifications POWER CONNECTIONSGrounding Instructions Functional Description KEY Features and ComponentsEXTENSION CORDS Contents Hardware Pack Product SpecificationsUnpacking Description QuantityFence Assembly AssemblyAlign Cutterhead to Outfeed Table Fence Angle Lock AssemblyAlign Cutterhead to Outfeed Table Connecting to Dust CollectorAdjusting Fence Position Locking the Jointer Using the Safety KEYOperation Starting and Stopping the JointerJointing Beveled Stock Feeding StockOutward 45 Angle Calibrating the 45/90 Stops Jointing Beveled StockTo Calibrate the 90 Stop Inward 45 AngleTo Calibrate the 45 Inward and Outward Stops Depth AdjustmentOther Recommended Maintenance MaintenanceChanging Cutterhead Knives Warranty AccessoriesFive Year Limited New Product Warranty Service and Repairs Replacement Parts Free Warning Label ReplacementPage Consignes DE Sécurité Définitions Consignes DE Sécurité ImportantesSuite à la Règles DE Sécurité GénéralesRègles DE Sécurité Spécifiques Supplémentaires Conservez CES Consignes Spécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Description Fonctionnelle Caractéristiques ET Composants ImportantsRallonges Déballage Caractéristiques DU ProduitDescription Quantité Contenu DU Carton DE QuincaillerieAssemblage DU Guide MontageAligner LE PORTE-OUTIL À LA Table DE Sortie Assemblage DE LA Butée Angulaire DU GuideBrancher LE Collecteur DE Poussière Aligner LE PORTE-OUTIL À LA Table DE Sortie suiteDémarrage ET Arrêt DE LA Dégauchisseuse FonctionnementRéglage DE LA Position DU Guide Jointoyer DU Matériel Biseauté Introduction DU MatérielAngle DE 45 Vers Lextérieur Étalonnage DES Butées DE 45/90 Jointoyer DU Matériel Biseauté suitePour Étalonner LA Butée DE Angle DE 45 Vers LintérieurRéglage DE LA Profondeur Pour Étalonner LES Butées DE 45 Entrantes ET SortantesRemplacement DES Lames DU PORTE-OUTIL Autre Entretien RecommandéEntretien Garantie AccessoiresGarantie limitée de cinq ans pour les produits neufs Service ET Réparations Aide Pour LES PIÈCES, LE Service OU LA GarantiePage Normas DE Seguridad Definiciones Instrucciones Importantes DE SeguridadContinúa en la página Reglas Generales DE SeguridadReglas Específicas DE Seguridad Adicionales Guarde Estas Instrucciones Especificaciones DEL Motor Conexiones DE AlimentaciónInstrucciones DE Conexión a Tierra Descripción Funcional Características Y Componentes ClaveAlargadores Eléctricos Desempaque Especificaciones DEL ProductoDescripción Cantidad Contenido DEL Paquete DE TornilleríaEnsamble DEL Tope Guía EnsambleEnsamble DEL Seguro DEL Ángulo DEL Tope Guía Conexión AL Colector DE Polvo Arranque Y Paro DEL Canteador FuncionamientoBloqueo DEL Canteador Usando LA Llave DE Seguridad Ajuste DE LA Posición DEL Tope GuíaCantear Material Biselado Alimentación DEL MaterialÁngulo Exterior DE Calibración DE LOS Topes DE 45/90 Cantear Material Biselado continuaciónPara Calibrar EL Tope DE Ángulo Interno DEAjuste DE LA Profundidad Para Calibrar LOS Topes Interior Y Exterior DEOtro Mantenimiento Recomendado MantenimientoCambio DE Cuchillas DE LA Cabeza DE Corte Garantía AccesoriosGarantía de producto nuevo limitada a cinco años Servicio Técnico Y Reparaciones Asistencia Sobre GARANTÍA, Servicio O PiezasPage Roush Street Anderson, SC 800