Hitachi WR 9DM, WR 12DM manual Battery REMOVAL/INSTALLATION, Charging, Application, Battery removal

Page 10

English

7. Bit adaptor: WR12DM: Code No. 991476 WR9DM: Code No. 996144

This is used for tightening small screws (M6 – M8).

NOTES

(1)This adaptor is set only on the anvil (drive angle) of the main unit. The bit adapter cannot be attached to the special accessory anvil (square drive).

(2)Before starting work with the adapter, tighten a few screws with it to make sure it’s tightening with the appropriate torque.

(3)Tightening speed will be greatly reduced when driving wood, tapping or other similar screws.

BATTERY REMOVAL/INSTALLATION

1.Battery removal

Hold the hadle tightly and push the battery latch to remove the battery. (Figs. 1 and 2)

CAUTION

Never short-circuit the battery.

2.Battery installation

Insert the battery while observing its polarities (see Fig. 2).

CHARGING

Applicable plus driver bit

L

Before using the impact wrench, charge the battery as follows.

1.Connect the charger’s power cord to a receptacle. When the power cord is connected, the charger’s pilot lamp will blink in red. (At 1-second intervals).

2.Insert the battery into the charger.

Insert the battery firmly, in the direction shown in

6.35Fig. 3, until it contacts the bottom of the charger compartment.

CAUTION

Bit

No.

 

 

 

 

 

Bit No.

 

L (mm)

Code No.

No. 2

 

45

955229

 

70

955654

 

 

No. 3

 

45

955230

 

70

955655

 

 

8.12.7 mm Square adaptor: WR9DM: Code No. 996145 This is used when using a socket with square hole dimensions of 12.7 mm.

If the battery is inserted in the reverse direction, not only recharging will become impossible, but it may also cause the fuse to blow, or problems in

the charger such as deformed recharging terminal.

3.Charging

When inserting a battery in the charger, charging will commence and the pilot lamp will light continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals.) (See Table 5)

(1)Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 5, according to the condition of the charger or the rechargeable battery.

Optional accessories are subject to change without notice.

APPLICATION

Tightening and loosening of all types of bolts and nuts, used for securing structural items.

9

Image 10
Contents WR 12DM WR 9DM Page 3mm Page Μπαταρία για τ WR12DM General Operational Precautions Precautions for Cordless Impact WrenchPower Tool SpecificationsStandard Accessories ModelFor WR9DM SocketsFor WR12DM Long SocketUniversal jointWR12DM Code No WR9DM Code No Extension bar WR12DM Code No WR9DM Code NoDuct Socket WR12DM Corner attachment Model EW-14RWR12DMCharging Battery REMOVAL/INSTALLATIONBattery removal ApplicationPrior to Operation How to make the batteries perform longerRegarding electric discharge in case of new batteries, etc HOW to USE Operational CautionsWork at a tightening torque suitable for the bolt Confirm the tightening torqueTightening torque Under impactNut Maintenance and Inspection Vorsicht FÜR Allgemeine Bedienung Vorsichtsmassnahmen FÜR DEN AKKU-SCHLAGSCHRAUBERELEKTRO-WERKZEUG ModellTechnische Daten LadegerätFür WR12DM Tafel StandardzubehörBuchsen Für WR9DMVorsicht Laden AnwendungHERAUSNEHMEN/EINSETZEN DER Batterie AnmerkungHinweis ROTGrün Zur Leistung von neuen BatterienVOR Inbetriebnahme VerwendungLassen Sie das Gerät nach fortlaufender Verwendung ruhen Vorsichtsmassregeln ZUR VerwendungÜberprüfung des Anzugsdrehmoments Abb Mutter AbbWartung UND Inspektion Lagern AußenreinigungInformation über Betriebslärm und Vibration Precautions Generales Precautions Pour LA CLE a Choc À BatterieOutil Electrique ModéleChargeur Accessoires Standards Douille à tubulure WR12DM Pour WR12DM TableauBarre de rallonge WR12DM No de code 873633 WR9DM No de code Joint universel WR12DM No de code 992610 WR9DM No de codeRemarque Extraction ET Installation DE LA BatterieCharge Adaptateur carré de 12,7 mm WR9DM No. de codeVerte RougeComment prolonger la durée de vie des batteries Avant LA Mise EN Marche UtilisationCouple de serrage Precautions DE FonctionnementRepos de l’appareil après un travail continu Manipulation de l’appareilPour WR12DM Kgfcm Entretien ET Controle Rangement Nettoyage de l’extérieurAu sujet du bruit et des vibrations Italiano Precauzioni PER LE Operazioni GeneraliCaratteristiche Accessori StandardModello Utensile ElettricoPer WR9DM Tabella Chiavi a incavoPer WR12DM Tabella Chiave a tuboAttenzione Chiave a condotto WR12DMRicarica Rimozione E Installazione Della BatteraApplicazioni NotaScarica nel caso di batterie nuove, ecc RossoVerde Come mantenere più lunga la durata delle batterieOperazione Prima DI Iniziare LE OperazioniCautela Momento di forze di fissaggio Precauzioni NELL’USORiposo dell’unità dopo lavoro continuo Come tenere l’attrezzoPer WR12DM Kgfcm M10 ⋅ Torsione 1000 800 Manutenzione E Controlli Pulizia della carcassa dell’utensile ConservazioneNederlands Algemene VoorzorgsmaatregelenMachine Technische GegevensStandaard Toebehoren AcculaderVoor de WR9DM Tabel BussenVoor de WR12DM Tabel Lange BusTunnelverbinding WR12DM Verlengstaaf WR12DM Code Nr WR9DM Code NrVoorzichtig Hoekverbinding Model EW-14RWR12DMOpladen ToepassingenInleggen EN Uitnemen VAN DE Batterij AantekeningOpmerking RoodGroen Betreffende het ontladen raken van nieuwe batterij e.dGebruik Voor HET GebruikLET OP Voorzorgsmaatregelen BIJ Gebruik Afb Moer AfbOnderhoud EN Inspectie WaarschuwingOpbergen Reiningen van de behuizingInformatie betreffende luchtgeluid en trillingen Precauciones Generales DE Operacion Precauciones Para LA Llave DE Impacto a BatteríaHerramienta Motorizada ModeloEspecificaciones CargadorPara WR12DM Tabla Accesorios EstándarCubos Para WR9DM TablaBarra de extensión WR12DM Código n˚ 873633 WR9DM Código n˚ Cubo largoPara WR12DM PrecaucionCarga AplicacionDesmontaje E Instalacion DE Bateria NotasDescarga eléctrica en caso de baterías nuevas, etc RojaForma de hacer que las baterías duren más Antes DE Usar LA Herramienta Como SE USASufeción de la herramienta Precauciones OperacionalesPar de apriete Confirmación de la tensión de aprietePara WR12DM Kgfcm Mantenimiento E Inspección Almacenamiento Limpieza en el exteriorObservacion Precauções COM a Chave DE Impacto Bateria Precauções Gerais Quanto À OperaçãoHitachi Ferramenta Elétrica EspecificaçõesRecarregador Para WR12DM Quadro ACESSÓRIOS-PADRÃOEncaixes Para WR9DM QuadroCódigo Nº Para WR9DMWR9DM AtençãoRETIRADA/INSTALAÇÃO DA Bateria AplicaçõesRecarga Quanto à descarga elétrica no caso de novas baterias, etc VermelhoComo prolongar a vida útil das baterias Antes DE Usar Modo DE UsarTorque de aperto adequado para o parafuso sob impacto Precauções OperacionaisTorque de aperto Para segurar a ferramentaAperto 1000 800 Manutenção E Inspeção Armazenagem Limpeza externaNformação a respeito de ruído e vibração do ar Γενικα Μετρα ΠΡ ΓΙΑ ΤΗ Λειτ ΠΡ Μετρα ΓΙΑ Τ ΜΠ ΜπαταριασWR9DM ΗλεκτρικΓια WR12DM ΚΑΝ ΕΓια WR9DM Μακριά υπ Για WR12DM Για WR9DM ΠίνακαςΑφαιρεση ΚΑΙ Τ Μπαταριασ ΕφαρμΣημειωσεισ Σημειωση Πριν ΤΗ Λειτ ΠΩΣ ΝΑ ΤΣημεια ΠΡ Κατα ΤΗ Λειτ Πίνακες 1 , 2 , 3 και Συντήρηση τ Συντηρηση ΚΑΙ ΕλεγΑντικατάσταση των καρ Βγάλτε τ τ καρ και µετά γαντ την Καθαρισµ 6901VVCMPS2L WR9DM EB9BCertificat DE Garantie Cettificado DE Garantia Guarantee Certificate GarantiebewijsGarantieschein Certificado DE Garantia Certificato DI Garanzia Πιστ ΕγγυησησPage Page Declaration DE Conformite CE Declaração DE Conformidade CE EC Declaration of Conformity EC Verklaring VAN ConformiteitDichiarazione DI Conformità CE EK ∆ΗΛΩΣΗ Εναρμ

WR 9DM, WR 12DM specifications

The Hitachi WR 12DM and WR 9DM are professional grade power tools designed to meet the needs of both DIY enthusiasts and construction professionals. These powerful models stand out in the market with their innovative features, advanced technology, and ergonomic design, making them ideal for a variety of applications such as drilling, fastening, and woodworking.

The Hitachi WR 12DM is equipped with a robust 12V motor that delivers impressive torque and speed, enabling it to tackle a wide range of fastening tasks with ease. It features a maximum torque of 130Nm, making it suitable for heavy-duty applications. The compact and lightweight design of the tool allows for easy maneuverability in tight spaces, reducing operator fatigue during extended use.

One of the standout technologies of the WR 12DM is its brushless motor, which provides several advantages over traditional brushed motors. This technology ensures longer runtime, increased efficiency, and reduced maintenance, as there are fewer moving parts that can wear out over time. Additionally, the integrated Electronic Speed Control allows for variable speeds, giving users the flexibility to adjust performance settings according to the demands of the task at hand.

On the other hand, the Hitachi WR 9DM offers a more compact solution, equipped with a 9V motor for lighter tasks. With a maximum torque of 90Nm, it is perfect for smaller projects and general maintenance work. The design is optimized for ease of handling, ensuring that it’s not only efficient but also comfortable to use for extended periods.

Both models emphasize user safety and convenience. They come with a built-in LED light that illuminates the workspace, ensuring visibility in low-light conditions. The ergonomic grip provides a comfortable hold, reducing stress on the hands during operation. Furthermore, both tools feature a keyless chuck for quick and easy bit changes, enhancing overall productivity.

The Hitachi WR series also showcases an excellent battery system, with Li-ion technology offering longer battery life and faster charging times. These features collectively make the WR 12DM and WR 9DM reliable choices for professionals looking for efficiency, power, and innovation in their tools. Together, they demonstrate Hitachi’s commitment to quality and performance in the power tool market.