Sharp KC-850U Care And Maintenance, BACK PANEL and SENSORS, Unit, Sensor Filter Care, E-5

Page 17
CARE AND MAINTENANCE

CARE AND MAINTENANCE

To maintain optimum performance of this air purifier, please clean the unit including the sensor opening and filters periodically.

When cleaning the unit, be sure to first unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result.

FILTER INDICATOR LIGHT Care Cycle

After 720 hours of use

(30days ×24hours = 720)

The Filter Indicator Light will illuminate as a reminder to perform mainte- nance of the Back Panel, Sensors, and Humidifying filter. The Indicator Light will turn on after approximately 720 hours of use.

After performing maintenance, reset the Filter Indicator. Plug the unit in, turn power ON, and press the RESET button for 3 seconds. The Filter Indicator Light will go off. Even if the Filter Indicator Light is already off, the RESET button should be pressed to reset the maintenance timer.

BACK PANEL and SENSORS

ENGLISH

Care Cycle

Whenever dust accumulates

on the unit or every 2 months

Gently remove dust from the sensor opening and the back panel, using a vacuum cleaner attachment or similar tool.

When the back panel has stubborn dirt

1

In case of oily dirt, soak the back panel in water with

kitchen detergent.

2

Avoid scrubbing the back panel when washing.

Rinse the back panel repeatedly with clean water to re-

move the solution residue.

3

Drip dry panel to remove excess water.

SENSOR FILTER CARE

Remove the sensor filter and tap it lightly over a sink or bin to dislodge dust. If it is very dirty, wash it gently with lukewarm water. Do not use any detergents or chemicals of any kind to clean the filter. Dry the filter completely before replacing in the unit. Do not operate unit without all filters properly installed.

Sensor

Back Panel

Back Panel

Sensor filter

UNIT

Care Cycle Whenever dust accumulates on the unit or every 2 months

To prevent dirt or stains on the unit, clean regularly. If stains are allowed to remain, they may become difficult to remove.

Wipe with a dry, soft cloth

For stubborn stains or dirt, use a soft cloth dampened with warm water.

Do not use volatile fluids

Benzene, paint thinner, polishing powder, may damage the surface.

Do not use detergents

Detergent ingredients may damage the unit.

E-5
Page 16 Page 18
Image 17
Page 16 Page 18
Contents Purificateur d’air à fonction d’humidification AIR PURIFIER with Humidifying FunctionMANUEL D’UTILISATION PURIFICADOR DE AIRE MANUAL DE OPERACIÓNWashable Deodorizing filter black Pre-filter True HEPA filter whiteENGLISH FEATURESCONTENTS FOR CUSTOMER ASSISTANCE the United States ACCESSORIES ADDITIONAL CUSTOMER INFORMATIONPARTS for your Authorized Parts Distributor Sharp Electronics CorporationSHARP ELECTRONICS CORPORATION CONSUMER LIMITED WARRANTYCONSUMER LIMITED WARRANTY FOR U.S. USERS Warranty Period for this Product335 Britannia Road East FOR CUSTOMER ASSISTANCE CanadaMississauga, Ontario L4Z 1W9 ACCESSORIES ADDITIONAL CUSTOMER INFORMATIONConsumer Electronics Products LIMITED WARRANTYCongratulations on your purchase SERVICEIMPORTANT SAFETY INSTRUCTIONS CAUTIONS CONCERNING OPERATION INSTALLATION GUIDELINESFILTER GUIDELINES ENGLISHBACK ILLUSTRATIVE DIAGRAM - FRONTPART NAMES FRONT MONITOR MAIN UNIT DISPLAYFilter Reset Button Indicator Light red2 Install the filters FILTER INSTALLATIONInstall the True HEPA filter 1 Remove the filters1 Removetop. the Water Tank by unlatching the REFILLING THE WATER TANK3After filling, securely tighten the Tank Cap 4Replace the Water Tank in the unit CLEAN AIR MODE CLEAN AIR & HUMIDIFY MODE 2 PressButton.the CLEAN AIR & HUMIDIFY MODE 1 Press the CLEAN AIR MODE Button on the displayPOWER OFF Button QUICK CLEAN MODEFAN SPEED Button Plasmacluster ON/OFF ButtonADJUSTMENT OF SENSOR DETECTION SENSITIVITY WATER SUPPLY INDICATOR LIGHTSound indicator setting for water supply 3 Press the Power OFF ButtonFILTER INDICATOR LIGHT Care Cycle CARE AND MAINTENANCEWhen the back panel has stubborn dirt BACK PANEL and SENSORSWASHABLE DEODORIZING FILTER CARE WATER TANK2Drip dry filter to remove excess water 4 Replace the filter in unit. See E-102Rinse the Humidifying Tray with lukewarm water HUMIDIFYING TRAY1Remove the Water Tank and Humidifying Tray HUMIDIFYING FILTER3 Preparingtion. the descaling solu CARE AND MAINTENANCEGuide for filter replacement timing FILTER REPLACEMENT GUIDELINESReplacement Filters Replacing the FiltersE-20 TROUBLESHOOTINGE-2 ERROR DISPLAYFlashing of the Clean Air Humidify Indicator LightStandby Power SPECIFICATIONSE-22 ENGLISH Filtre désodorisant lavable noir Pré-filtre Filtre HEPA authentique blancTABLE DES MATIÈRES FRANÇAISCARACTÉRISTIQUES POUR VOUS PROTÉGER Produits Électronique grand public GARANTIE LIMITÉEBravo! Vous Venez de faire un excellent achat LE SERVICEINSTRUCTIONS DE SÉCURITÉ IMPORTANTES PRÉCAUTIONS CONCERNANT LE FONCTIONNEMENT GUIDE D’INSTALLATIONGUIDE D’UTILISATION DES FILTRES FRANÇAISDOS DE L’APPAREIL DÉSIGNATION DES PIÈCESSCHÉMA ILLUSTRATIF - AVANT MONITEUR AVANT AFFICHAGE DE L’UNITÉ PRINCIPALEFRANÇAIS des témoins2 Installez les filtres INSTALLATION DES FILTRES1 Installez le filtre HEPA authentique 1 Retirez les filtresAprès le remplissage, serrez bien le bou REMPLISSAGE DU RÉSERVOIR D’EAU3 chon du réservoir 4 Replacez le réservoir d’eau dans l’appareilMODE D’ÉPURATION DE L’AIR ET D’HUMIDIFICATION FONCTIONNEMENTMODE D’ÉPURATION DE L’AIR Bouton DE VITESSE DU VENTILATEUR MODE D’ÉPURATION RAPIDEBouton D’ARRÊT DE L’APPAREIL Bouton DE MARCHE/ARRÊT DU PlasmaclusterLAMPE D’ALIMENTATION EN EAU Bouton DE CONTRÔLE DES TÉMOINSRÉGLAGE DE LA SENSIBILITÉ DES CAPTEURS AnnulationLAMPE DU FILTRE SOIN ET ENTRETIENPANNEAU ARRIÈRE ET CAPTEURS APPAREILENTRETIEN DU FILTRE DÉSODORISANT LAVABLE RÉSERVOIR D’EAUSOIN ET ENTRETIEN F-5 BAC D’HUMIDIFICATIONSOIN ET ENTRETIEN FILTRE D’HUMIDIFICATIONF-6 Guide de remplacement des filtres GUIDE DE REMPLACEMENT DES FILTRESRemplacement des filtres Filtres de rechangeF-8 RÉSOLUTION DES PROBLÈMESF-9 AFFICHAGE D’ERREURFRANÇAIS Clignotement de la lampeConsommation en veille CARACTÉRISTIQUESF-20 FRANÇAIS F-2NOTA Lea antes de operar su nuevo Purificador de aireCONTENIDO ESPAÑOLCARACTERÍSTICAS INSTRUCCIONES DE SEGURIDAD IMPORTANTES PAUTAS PARA LA INSTALACIÓN PRECAUCIONES RELACIONADAS CON LA OPERACIÓNPAUTAS PARA EL FILTRO ESPAÑOLPARTE POSTERIOR DIAGRAMA ILUSTRATIVO - PARTE FRONTALNOMBRE DE LAS PARTES MONITOR FRONTAL PANTALLA DE LA UNIDAD PRINCIPALESPAÑOL Botón reestablecer filtro1 Retire los filtros INSTALACIÓN DEL FILTRO2 Instale los filtros 1 Instale el filtro HEPAPRECAUCIÓN LLENADO DEL TANQUE DE AGUA4 Reemplace el tanque de agua en la unidad 2 Presione el botón de Modo CLEAN AIR MODO CLEAN AIR AIRE LIMPIOOPERACIÓN 1 Llene el tanque de agua. Vea S-7Botón POWER OFF APAGADO MODO QUICK CLEAN LIMPIEZA RÁPIDABotón FAN SPEED VELOCIDAD DEL VENTILADOR Botón Plasmacluster ON/OFF ENCENDIDO/APAGADOLUZ DEL INDICADOR DE SUMINISTRO DE AGUA Botón LIGHTS CONTROL CONTROL DE LUCESAJUSTE DE LA SENSIBILIDAD DE DETECCIÓN DEL SENSOR OPERACIÓNDEL FILTRO CUIDADO Y MANTENIMIENTOPANEL POSTERIOR y SENSORES UNIDADCUIDADO DEL FILTRO DESODORIZADOR LAVABLE TANQUE DE AGUA4 Reemplazo del filtro en la unidad. Vea S-6 S-12PRECAUCIÓN BANDEJA DEL HUMIDIFICADORCUIDADO Y MANTENIMIENTO FILTRO DEL HUMIDIFICADORS-14 Guía para programar el reemplazo del filtro PAUTAS PARA REEMPLAZAR EL FILTROFiltros de reemplazo Reemplazo de los filtrosS-16 LOCALIZACIÓN DE FALLASS-17 MENSAJES DE ERRORESPAÑOL Destello de la luz delEnergía de reserva ESPECIFICACIONESS-18 ESPAÑOL SHARP CORPORATION SHARP ELECTRONICS CORPORATIONSHARP CORPORATION Sharp Plaza, Mahwah
Top Page Image Contents