HP General IO Connectivity manual Planning and Preparation, Card Compatibility, On-Line Addition

Page 104

OLA/R Overview and Concepts

Planning and Preparation

Planning and Preparation

For the most part SAM prevents you from performing OLA/R procedures that would adversly affect other areas of the server. This section provides you with important information that can help minimize errors or problems when performing OLA/R procedures.

Card Compatibility

On-Line Addition

When on-line adding an interface card, the first issue that must be resolved is whether the new card is compatible with the system. Each OLA/R-capable PCI slot provides a set amount of power. The replacement card cannot draw more power than is available.

The card must also operate at the slot’s bus frequency. A PCI card must run at any frequency lower than its maximum capability, but a card that could only operate at 33 MHz would not work on a bus running at 66 MHz. rad provides information about the bus frequency and power available at a slot, as well as other slot-related data.

On-Line Replacement

When on-line replacing an interface card, the replacement card must be identical to the card being replaced. This is referred to as like-for-likereplacement and should be adhered to because using a similar but not identical card may cause unpredictable results. For example, a newer version of the target card which is identical in terms of hardware may contain an updated firmware version that could potentially conflict with the current driver.

The PCI specification allows a single physical card to contain more than one function. A single-function SCSI bus adapter can not be replaced by a dual-function adapter, even if the additional function on the card was identical to the original SCSI bus adapter.

When the replacement card is added to the system, the appropriate driver for that card must be configured in the kernel before beginning the operation. SAM ensures the correct driver is present. (In most cases, the replacement card will be the same type as a card already in the system, and this requirement will be automatically met.) If you have any

104

Chapter 4

Image 104

Contents Edition Manufacturing Part Number J2793-90073 E0607Legal Notices Contents Diagnostic Utilities PAD Services Tracing and Logging Utilities SUsing Non-English Subscription Forms Diagnostic Messages Tables Tables Tables Tables Figures Figures About the X.25 Product Introduction Link Architecture BSD IPC TCP/UDPApplication L7, Presentation L6, Session L5 Levels Transport Level L4 Packet/network Level L3 Data link L2 and Physical L1 Levels Data link L2 and Physical L1 Levels Chapter Installation Before you Install the software Installing Multiple X.25 Interface CardsHardware Requirements Hardware CompatibilityRelated Parameters OS Platform and Version CompatibilityMemory Example TM = 9,123,840 8.7 Mb Software Requirements Installing the X.25 Link Software StepInstalling the X.25 Link Software Chapter Configuration Configuring the X.25 Link Using SAMUsing SAM’s On-line Help Configuring an X.25 Address Field Descriptions Configuring X.25 Virtual Circuits VCs Configuring an Internet Address Configure Internet Address Configure Internet Address Field Descriptions IP Address and Default Subnet Masks ClassModify IP Over X.25 Defaults IP Address and Default Subnet MasksIP Address Class Default Subnet Mask Modify IP over X.25 Defaults Field Descriptions Verifying Level 3 ValuesVerify Level 3 Values Verify Level 3 Values Field DescriptionsDefault is Modulo-8 Switched VC Flow Control Field Descriptions Permanent VC Flow Control Field DescriptionsConfiguring the X.25 Link Verifying Level 2 Values Throughput Classes and Line SpeedsSettings for your configuration Verify Level 2 Values Field Descriptions Using Maximum Window-Size Settings with Modulo-128 Recommended Maximum Window Sizes Level 3 Packet Level 2 Window SizeConfiguring Remote System Access Add Internet Connectivity Dialog Add Internet Connectivity Field Descriptions X25init -cconfigurationfile-a ipmapfile Provide X.25 Information Field Descriptions Internet Addresses & Routes object list. SAM updates Configuring X.25 over LLC2 Configuration FilesField Format Value Patch requirements for the XOL HA feature and configurableAdditional XOL specific configuration parameters Xoldsap Devicelan00x7c Lanboxid Lanboxaddr 0x080009c4728a 0x7e Example 3-3 LLC2 Configuration Ccitt Run the following command at the Cisco console Starting and Stopping Configuration Step Run the following command at the Cisco consoleSample setup and Configuration One Lan and Two Boxes configuration11 One LAN, Two Boxes Configuration To connect Host to BOX To connect Host to BOX To Connect Box 1 to Host Configuring Two Lans, with One Box Per Lan To configure Host to LAN 1 to BOX To Start and Stop above configurationTo Connect Box 0 to Host To Connect Box 1 to Host Troubleshooting LLC2 Configuration Remote Configuring PAD ServicesAdd/Modify PAD Terminal Emulation Local to Add/Modify PAD Support Server Remote to Local Add/Modify PAD Printers Server Add/Modify Uucp ServerAdd/Modify X.3 Parameters PAD. As the terminal characteristics of your session change, Configuring the High Availability Feature Commands to be Configured in High Availability Packages Cluster DefinitionHigh Availability Configuration Example 3-4 One Example of Remote FailureChecking the Configuration $ x25checkX25check 250207 -i interface0p2 Configuring the High Availability Feature for X.25 over LLC2 Unique MAC Address RequirementConfiguring XOL HA for Local Failover Without ServiceGuard Local Failover13 Before the Failover After the Failover Example Configuring Standby Device and Unique MAC Address Configuring XOL HA for Remote Failover Using Service Guard Remote Failover15 Before the Failover Commands Used in the SG Package Control Scripts XOL Cluster DefinitionXOL Package Definition Example 3-6 XOL SG package for remote failover Remote Failover with Local Failover Support Using Service GuardThen, the above parameters take the following values Example Remote Failover with Local Failover support # Service Names and Commands Configuring the High Availability Feature for X.25 over LLC2 Verifying the X.25 Link Ping100 OLA/R Overview and Concepts 102 Important Terms and Concepts Terms used in this section MeaningOn-Line Replacement Planning and PreparationCard Compatibility On-Line AdditionCritical Resources Failover Actions / Single Points of Failure How to On-line Replace OLR a J3525A or J3526A PCI Card using SAMInterface card under consideration will be stopped before Disconnect messages. The connections will have to beThree Possible Critical Resource Analysis CRA Outcomes Screen Buttons Outcome Activate User Actions DisplaysChapter 109 110 How to On-line Add OLA a J3525A or J3526A PCI Card using SAM112 Chapter 113 114 Diagnostic Utilities Using Diagnostic Utilities Available Diagnostic Utilities Utility Description Refer toScope of X.25 Diagnostic Utilities PsidadBefore Using the Diagnostic Utilities X25check and x25server Example 1 Running x25check Interactively No Parameters120 Example 2 Running x25check With an X.121 Address Example 3 Running x25check With a Data PacketExample 1 Displaying the Current Configuration X25statExample 2 Displaying Global Statistics X25stat -d X25stat -g -dDiagnostic Utilities x25stat Level 3 State Output on Screen Description/MeaningLevel 3 State Level 2 Link State Output on Screen Description/MeaningLevel 1 Link State Output on Screen Description/Meaning VC State Output on Screen Description/Meaning Example 3 Displaying Virtual Circuit Data PacketCounters VC State Example 4 Displaying Global X.25 Level 3 StatisticsExample 5 Displaying X.25 Level 1 and 2 Statistics Chapter 129 Example 6 Displaying Virtual Circuit Status Example 7 Displaying Current IP to X.25 Address Mapping X25stat -aX25mibstat Example Statistics for x25mibstat X25mibstat Option RemarkPAD Services Ccitt Recommendations PAD services and the HP 9000 host PAD Support ProtocolsOverview PAD Services as a PipeRemote PAD Support x29server Remote PAD Support Call Acceptance Mechanism and System Security0x01000000 Supported Remote PAD Terminals Configuring Remote PAD SupportConfiguring padspt Parameters Padspt Parameters Chapter 141 Launching Applications Automatically Remote PAD Printer Support x29printd Remote PAD Printer Support x29printdSystem Requirements Remote Printer SupportConfiguring Remote PAD Printers 146 Configuring the Unix Line-printer Spooler for x29printd X29printd and lpsched Operation Printer ConfigurationExamples Verifying the Configuration Uucp Support x29uucpd Configuring Uucp PAD Support Receiving HPPaduucp Parameters File ContentsConfiguring the x29hosts file Chapter 153 Configuring System and Device Files for Uucp At the dave systemChapter 155 At the bill system Chapter 157 158 Chapter 159 Command Mode Local PAD Emulation pademParameter Descriptions Data Transfer ModeConfiguring Local PAD Emulation 162 Chapter 163 PAD Commands PAD Command SetExtended Command Set 166 Configuring X.3 Profile Parameters Configuration Set SyntaxModifying Parameters Parameter ValuesDefault X.3 Parameters Parameter DescriptionsParameter Description Value MeaningChapter 171 172 Value Baud Rate 174 Chapter 175 176 Chapter 177 178 Tracing and Logging Utilities 180 Scope of X.25 Tracing and Logging Utilities Parameters NettlSyntax Tracing Masks Keyword a 0x800000000x40000000 0x20000000184 Netfmt Chapter 185186 Creating a Filter File Filter File SyntaxFilter File Options System/subsystem Type Value Level FilterChapter 189 Filter File Examples Strace Chapter 1917030 7030 + 1 = Chapter 193Output Format Packet Type Parameters Displayed Frame Type Parameters DisplayedExamples of the strace Command Examples of strace Output Record Time Tics Pri Ind Mod Sub Data Num198 Strerr 200 Troubleshooting Troubleshooting Your X.25 Link Troubleshooting Commands Purpose Refer toTroubleshooting Flowcharts and Procedures Troubleshooting CommandsFlowchart 2 Procedures and Notes FlowchartChapter 205 Flowchart 2 Initialization Check See NoteFlowchart 3 Procedures and Notes Flowchart 3 Hardware and License CheckFlowchart 4 Procedures and Notes Flowchart 5 Procedures and Notes Flowchart 4 X.25 Configuration Check210 Flowchart 5 IP Over X.25 Check For Systems With No Backup Power Supply Recovering From a Power FailureFor Systems With a Backup Power Supply Reporting Problems 214 Back-to-back Configuration on the Same Host Host216 Configuration and Troubleshooting Commands Command Summary218 Examples of x25init IP-to-X.121 Address Mapping TableSyntax for SVCs Syntax for PVCsFile Mapping Parameters 222 Chapter 223 224 Using Non-English Subscription Subscription Form Translations TranspacTable A-1 French Transpac Subscription Form ItapacTable A-2 Using Your Itapac Italian Subscription Form Throughput Class SettingTable A-4 Using your Iberpac Spanish Subscription Form 230 Configuration Files Table B-2 Etc directory Configuration FilesTable B-1 Etc/x25 directory Table B-5 Table B-3 Var/x25/log/x25server directoryTable B-4 Table B-6 Example FilesX25initdef File Appendix B 235 236 X25initsmpl File Table B-7238 X3config File 240 Example Files Appendix B 241 X29hosts File Table B-8Network Type File x25networks Table B-9 Diagnostic Messages Appendix C Diagnostic Message Example Cause Code Settings Restart Packet Codes RESET/CLEAR Packet CodesPacket Codes Diagnostic Messages Table C-1 No Additional Information DiagnosticTable C-2 Packet Type Invalid Diagnostic ExplanationTable C-3 Packet Not Allowed Diagnostic Table C-2 Packet Type InvalidTable C-3 Packet Not Allowed LCITable C-4 Timer Expired Diagnostic IncomingTable C-4 Timer Expired Appendix C 255 256 Appendix C 257 Table C-6 Category Miscellaneous Diagnostic Table C-7 International Problem and Maintenance DiagnosticTable C-7 International Problem and Maintenance Table C-8 DTE-Specific Signals DiagnosticTable C-8 DTE-Specific Signals Table C-9 OSI Network Service Problem DiagnosticTable C-9 OSI Network Service Problem NsapTable C-10 Higher Level Initiated Diagnostic Table C-10 Higher Level Initiated 264 Symbols Index266 267 268 269

Related manuals

Manual 4 pages 45.44 Kb

Manual 14 pages 39.26 Kb