GSI Outdoors PNEG-377 Roof WARNING, Operation & Safety, Roof Damage Warning and Disclaimer

Page 4

ROOF WARNING, OPERATION & SAFETY

Fan and Heater

Roof Damage Warning and Disclaimer

GSI DOES NOT WARRANT ANY ROOF DAMAGE CAUSED BY EXCESSIVE VACUUM OR INTERNAL PRESSURE FROM FANS OR OTHER AIR MOVING SYSTEMS. ADEQUATE VENTILATION AND/OR "MAKEUP AIR" DEVICES SHOULD BE PROVIDED FOR ALL POWERED AIR HANDLING SYSTEMS. GSI DOES NOT RECOMMEND THE USE OF DOWN- WARD FLOW SYSTEMS (SUCTION). SEVERE ROOF DAMAGE CAN RESULT FROM ANY BLOCKAGE OF AIR PASSAGES. RUNNING FANS DURING HIGH HUMIDITY/COLD WEATHER CONDITIONS CAN CAUSE AIR EXHAUST OR INTAKE PORTS TO FREEZE.

Proper Use of Product

This product is intended for the use of grain drying only! Any other use is a misuse of this product. This product has sharp edges! These sharp edges may cause serious injury. To avoid injury handle sharp edges with caution and use

proper protective clothing and equipment at all times. Guards are removed for illustration only.All guards

must be in place before and

during operation.

The symbol shown is used to call your attention to instructions con- cerning your personal safety. Watch for this symbol; it points out important safety precautions. It means "ATTENTION", "WARNING", "CAUTION", and "DANGER". Read the message and be cautious to the possibil- ity of personal injury or death.

Safety Alert Symbol

WARNING! BE ALERT!

Personnel servicing fans and heaters should read this manual. Failure to read this manual and its safety instructions is a misuse of the equipment.

4

Image 4
Contents Service Manual Page Table of Contents Roof WARNING, Operation & Safety Safety Alert SymbolRoof Damage Warning and Disclaimer Proper Use of ProductPower Warning SafetyFuel Warning Page Vane Axial Fans FAN Installation Previously Installed UnitsProper Installation of the Ground Rod Machine to Earth GroundTest Station FAN Specifications RPM Vane Axial FanFAN FAN Troubleshooting Fan Troubleshooting ChartFan Control Circuit TroubleshootingPush Start Button, Nothing Happens FAN Wiring and Schematic Volt 1 Phase 15 HPFAN Service LubricantMotors with Regreasing Grease in motor bearingsHub Bolt Torque Requirement for Fan Blades 84 ft. lbs. Trantorque14 1HP 18-1.5HPCentrifugal FAN Service Guide RPM FAN RPM FAN Specifications 150 200 100 Volt 1 Phase 15 HP Marathon FAN Schematic and WiringSchematic Wiring Diagram Lubrication ProcedureRelubrication Intervals 15HP 3500RPM fans 16ft. lbs. Browning 29ft. lbs. BrowningGas Heater Service Guide Bin Configuration Heater InstallationOperating Temperature Table Disconnectand LOCK-OUT Power Before Servicing Heater Replacing HF-7100 Board with HF-7318High Temperature Heater Specifications Low Temperature Heater SpecificationsVane Axial GAS Heater Specifications BTUs per Gauge Pressure PSI Propane Models ApproximateBTUs Gauge Pressure PSI Natural Gas Models Approximate CHI-TOWN GAS Heater Specifications Low & Medium Temperature ModelsCHI-TOWN Heater Specifications High TemperatureMED Temperature Btus Per Gauge Pressure Psi Natural Gas Models ApproximateDownwind Heater Specifications Centrifugal Heater SpecificationsAir Pressure Switch Temperature Sensor Box Installation Transition Hi-limit InstallationHeater Unit Wiring Secondary Heater UnitInstalling Optional Humidity Sensor Figure aOperating Procedure Power UpNormal Operating Displays With Heater Not Running Setting Gas Pressure Starting The DryerOperating Procedure AIR Pressure Switch Adjusting the Air Pressure SwitchAdjusting The Vaporizor Running The DryerProgramming Set Points Drying Grain Hours To Shutdown Mode Programming Hours To ShutdownRun Hours Display Multiple Heater NotesModulating Valve Operation Amount of gas used by the heaterConfiguration Dip Switches Normally Done Factory ConfigurationAt GSI Error Conditions Limit SwitchesMultiple Heater Error Conditions Misc Error NumbersHeater Service Wiring Diagram Turn Control Power on dryer to the off position Programing Instructions for Series 2000 Heater+18% Programmer Hook UpHeater Electrical Installation 230V Fans Heater Electrical InstallationConnect power cord to fan control box Transition HI-LIMIT Installation Mount the housing to the bin Sidewall to sealPlenum Thermostat Mounting To the right sideAnnual Heater Inspection For Units Using HF-7318 Control Board Installation For Standard UnitsRun 2 wires 18 gage between master and slave unit FAN PartsWiring Schematic Standard Heater Wiring Standard Heater Schematic TROUBLE-SHOOTING Flow Chart HousingTrouble Shooting Chart 7528% 352%$%/&$86Fan and Heater Gas Heaters Deluxe Heater Wiring Deluxe Heater Schematic Heaters Installation Standard Units 2ND Heater InstallationInstallation HI-LO Units Standard Heaters not HI-LO fire Smart BoardHI-LO Fire Heater Light Identification Troubleshooting ChartDescription Fan And Heater Downwind Heat Adjustment Procedure For Heaters Manufactured afterGAS Heaters 2ND Heater Installation Wiring Schematic GAS Heaters Electrical CHECK-OUT Chart Purge DelayTime Delay Reset Flame Probe2ND Heater Installation PRE-1990 GAS Heaters Heater Wiring Diagram Heater Schematic Vane Axial LP HeaterVane Axial Vapor Heater Downwind LP Heater Downwind Vapor Heater Lo-Fire Downwind Heater Miscellaneous Information 1991-1993PNEG-286 Flame Detector Kit Installation Flame Detector KIT InstallationPart Number HF-7136 1994-1995PNEG-286 Flame Detector Kit Installation PRESENTPNEG-286 Installation SELF-OPERATED Modulating ValvesApplication OperationBypass Orifice Selection Orifice Sizes in Kit Number PLG14A-600RAdjustment Checkout ProcedureRepairs and Replacement Replacement PartsInstallation Instructions Manual ResetFENWAL-SERIES SeriesSpecifications Flame SensingElectrode Application Control Board CommentsFan and Heater Control Board System ChecksPolarity Check Initial OperationFENWAL-SERIES Safety Checks Repair and ReplacementsLimited Warranty Statement WARRANTY/SERVICE NotesTwisto Says Motor Capacitor Chart Page 1004 E. Illinois St Assumption, IL Phone Fax February