GSI Outdoors PNEG-377 service manual Safety, Fuel Warning, Power Warning

Page 5

Fan and Heater

SAFETY

CAUTION! BE VERY

CAREFUL WHEN

CHECKING OUT 220V OR 460V CONTROL CIRCUIT.

SERIOUS INJURY OR DEATH MAY OCCUR IF PROPER PRECAUTIONS ARE NOT TAKEN.

The GSI Group, Inc. recom- mends contacting your local power company, and having a representa- tive survey your installation so the wiring is compatible with their sys- tem, and adequate power is sup- plied to your unit.

Safety decals should be read and understood by all people in the grain handling area.

If a decal is damaged or is missing contact:

GSI Group, Inc.

1004 E. Illinois St. Assumption, IL 62510 217-226-4421

A free replacement will be sent to you.

BE SURE POWER IS DISCONNECTED AND LOCKED OUT BEFORE INSTALLATION. FAILURE TO DO SO MAY CAUSE SERIOUS INJURY OR DEATH

FAILURE TO INSTALL

THERMOSTAT INCREASES RISK OF FIRE IN BIN!

WARRANTIES ARE VOID ON HEATERS INSTALLED

WITHOUT THERMOSTATS.

Fuel Warning

Important! Do not use propane tanks which have previously been used for ammonia unless they have been purged according to procedures of the National L. P. Association.

Be sure fuel supply system complies with all local codes for L. P. gas installations.

DO NOT USE FLAME FOR LEAK TESTING.

Power Warning

Be sure power is disconnected and locked out before installation!

Failure to do so may cause serious injury or death.

Important! Heater must be interlocked with fan for safe operation.

Important! Thermostat must be installed for safe operation.

5

Image 5
Contents Service Manual Page Table of Contents Safety Alert Symbol Roof WARNING, Operation & SafetyRoof Damage Warning and Disclaimer Proper Use of ProductFuel Warning SafetyPower Warning Page Vane Axial Fans Previously Installed Units FAN InstallationProper Installation of the Ground Rod Machine to Earth GroundTest Station RPM Vane Axial Fan FAN SpecificationsFAN Fan Troubleshooting Chart FAN TroubleshootingPush Start Button, Nothing Happens TroubleshootingFan Control Circuit Volt 1 Phase 15 HP FAN Wiring and SchematicLubricant FAN ServiceMotors with Regreasing Grease in motor bearings84 ft. lbs. Trantorque Hub Bolt Torque Requirement for Fan Blades14 1HP 18-1.5HPCentrifugal FAN Service Guide RPM FAN RPM FAN Specifications 150 200 100 Schematic Wiring Diagram FAN Schematic and WiringVolt 1 Phase 15 HP Marathon Relubrication Intervals ProcedureLubrication 29ft. lbs. Browning 15HP 3500RPM fans 16ft. lbs. BrowningGas Heater Service Guide Operating Temperature Table Heater InstallationBin Configuration Replacing HF-7100 Board with HF-7318 Disconnectand LOCK-OUT Power Before Servicing HeaterLow Temperature Heater Specifications High Temperature Heater SpecificationsBTUs per Gauge Pressure PSI Propane Models Approximate Vane Axial GAS Heater SpecificationsBTUs Gauge Pressure PSI Natural Gas Models Approximate Low & Medium Temperature Models CHI-TOWN GAS Heater SpecificationsHigh Temperature CHI-TOWN Heater SpecificationsBtus Per Gauge Pressure Psi Natural Gas Models Approximate MED TemperatureCentrifugal Heater Specifications Downwind Heater SpecificationsTransition Hi-limit Installation Air Pressure Switch Temperature Sensor Box InstallationSecondary Heater Unit Heater Unit WiringFigure a Installing Optional Humidity SensorPower Up Operating ProcedureNormal Operating Displays With Heater Not Running Starting The Dryer Setting Gas PressureOperating Procedure Adjusting the Air Pressure Switch AIR Pressure SwitchRunning The Dryer Adjusting The VaporizorProgramming Set Points Programming Hours To Shutdown Drying Grain Hours To Shutdown ModeRun Hours Display Multiple Heater NotesAmount of gas used by the heater Modulating Valve OperationAt GSI Factory ConfigurationConfiguration Dip Switches Normally Done Limit Switches Error ConditionsMultiple Heater Error Conditions Misc Error NumbersHeater Service Wiring Diagram Programing Instructions for Series 2000 Heater Turn Control Power on dryer to the off positionProgrammer Hook Up +18%Connect power cord to fan control box Heater Electrical InstallationHeater Electrical Installation 230V Fans Mount the housing to the bin Sidewall to seal Transition HI-LIMIT InstallationPlenum Thermostat Mounting To the right sideAnnual Heater Inspection Installation For Standard Units For Units Using HF-7318 Control BoardRun 2 wires 18 gage between master and slave unit FAN PartsWiring Schematic Standard Heater Wiring Standard Heater Schematic Housing TROUBLE-SHOOTING Flow Chart7528% 352%$%/&$86 Trouble Shooting ChartFan and Heater Gas Heaters Deluxe Heater Wiring Deluxe Heater Schematic Heaters Installation HI-LO Units 2ND Heater InstallationInstallation Standard Units HI-LO Fire Heater Smart BoardStandard Heaters not HI-LO fire Description Troubleshooting ChartLight Identification For Heaters Manufactured after Fan And Heater Downwind Heat Adjustment ProcedureGAS Heaters 2ND Heater Installation Wiring Schematic GAS Heaters Purge Delay Electrical CHECK-OUT ChartTime Delay Reset Flame Probe2ND Heater Installation PRE-1990 GAS Heaters Heater Wiring Diagram Vane Axial LP Heater Heater SchematicVane Axial Vapor Heater Downwind LP Heater Downwind Vapor Heater Lo-Fire Downwind Heater Miscellaneous Information Part Number HF-7136 Flame Detector KIT Installation1991-1993PNEG-286 Flame Detector Kit Installation 1994-1995PNEG-286 Flame Detector Kit Installation PRESENTPNEG-286 SELF-OPERATED Modulating Valves InstallationApplication OperationOrifice Sizes in Kit Number PLG14A-600R Bypass Orifice SelectionCheckout Procedure AdjustmentRepairs and Replacement Replacement PartsManual Reset Installation InstructionsFENWAL-SERIES SeriesFlame Sensing SpecificationsElectrode Application Control Board CommentsSystem Checks Fan and Heater Control BoardPolarity Check Initial OperationFENWAL-SERIES Repair and Replacements Safety ChecksTwisto Says WARRANTY/SERVICE NotesLimited Warranty Statement Motor Capacitor Chart Page 1004 E. Illinois St Assumption, IL Phone Fax February