Lennox International Inc SL280UH070V36A DIP Switch Settings and On−Board Links See figure

Page 29

TABLE 11

SL280 Field Wiring Applications With Conventional Thermostat

	DIP Switch Settings and On−Board Links (See figure 34)
	DIP Switch 1	On Board Links Must Be Cut To Select
Thermostat	Thermostat	On Board Links Must Be Cut To Select		Wiring Connections
Thermostat	Thermostat	System Options		Wiring Connections
	Heating	System Options
	Heating
	Stages
1 Heat / 1 Cool	ON		S1	FURNACE	OUTDOOR
NOTE − Use DIP			T’STAT	TERM. STRIP	UNIT
NOTE − Use DIP
switch 2 to set
second−stage
heat ON delay.		DO NOT CUT ANY
OFF−7 minutes.		ON−BOARD LINKS			*
OFF−7 minutes.					*
ON−12 minutes.

1 Heat / 2 Cool	ON	S1	FURNACE	OUTDOOR
NOTE − Use DIP		T’STAT	TERM. STRIP	UNIT
NOTE − Use DIP
switch 2 to set
second−stage
heat ON delay.		CUT ON−BOARD LINK		*
OFF−7 minutes.		W915
OFF−7 minutes.		2 STAGE
ON−12 minutes.		2 STAGE
ON−12 minutes.		COMPR

1 Heat / 2 Cool	ON	CUT ON−BOARD LINK	S1	FURNACE	OUTDOOR
with t’stat with		CUT ON−BOARD LINK	T’STAT	TERM. STRIP	UNIT
with t’stat with		W915	T’STAT	TERM. STRIP	UNIT
humidity control		2 STAGE
humidity control		COMPR
		COMPR
NOTE − Use DIP
switch 2 to set					*
second−stage					*
heat ON delay.
OFF−7 minutes.		CUT ON−BOARD LINK
OFF−7 minutes.		W914
ON−12 minutes.		W914
ON−12 minutes.		DEHUM
		OR
		HARMONY
				o

* Not required on all units.

Page 29

Image 29

Contents Table of Contents Installation Instructions SL280UHVReturn air from both sides Unit Dimensions − inches mmSide Return Air Opening Either SideSight Glass Access Panel Blower AssemblyParts Arrangement Shipping and Packing List Safety InformationSL280UHV Gas Furnace General Use of Furnace as Construction HeaterAir Handler Unit EvaporatorCombustion, Dilution & Ventilation Air Space ALL AIR from Inside Equipment in ConfinedEquipment Confined Space ALL AIR from Outside Equipment in Confined Space ALL AIR from OutsideEquipment in Confined Space Blower Motor Rigid LEG Setting EquipmentBottom Furnace Front 20 X 25 XIndoor AIR Return AIR BaseRight Horizontal Application Installation Clearances Top LeftEnd Bottom Typical Horizontal ApplicationDuct System FiltersUpflow Position VentingTop Vent Discharge Left Side Vent DischargeSide Vent Discharge Horizontal Left PositionHorizontal Right Position Disconnected Vent Common Venting Using Metal−Lined Masonry ChimneySticker Vent PipeThrough an unused masonry chimney flue is not considered Vent Connector102 127 −1/2 152 178 10−1/2 MIN MAX Feet FAN + FAN FAN + NAT 130 Carbon Monoxide Poisoning Hazard − In some localities, codes may require the installation Ers or straps. Install a drip leg in vertical pipe runs toGas Piping Every 8 to 10 feet 2.44 to 3.01 m with suitable hangRight−Side Air Discharge Horizontal ApplicationLeft−Side Air Discharge Electrical Interior MAKE−UP BOX InstallationElectrostatic Discharge ESD BOXCommunicating Non−CommunicatingIcomfortt Integrated Control Outdoor Unit Icomfort Touch Communicating System Wiring NON−COMMUNICATING System Wiring120V Connections ApplicationsDIP Switch Settings and On−Board Links See figure OFF Single Stage Thermostat w Dual fuel capa Bilities SL280UHV Schematic Wiring Diagram Typical SL280UHV Field Wiring Diagram + = Data High Connection − = Data LOW Connection Integrated ControlRS−BUS Link TB82, future use −10% approx OFF On−Board Links 985 1045940 880SL280UH090V36B Blower Performance less filter 1220 12801155 10951235 12951170 11101230 13601165 11001225 12901160 1380+18% 1605 SL280UH110V60C Blower Performance less filter +18% 1785 SL280UH135V60D Blower Performance less filter Operating Sequence Thermostat energizes Y2 CompressorUnit Start−Up For Your Safety Read Before LightingWhite Rodgers GAS Valve Honeywell GAS ValveGAS Meter Clocking Chart Gas Pressure AdjustmentProper Combustion DialHigh Altitude Heating Sequence of Operation Other Unit AdjustmentsSEC Heating Operation with TWO−STAGE ThermostatHeating Operation with Single Stage Thermostat Electrical SHOCK, Fire Or Explosion Hazard Service13− To clean the combustion air inducer visually inspect SL280UHV BURNER, Combustion AIR Inducer Assembly11− Back wash using steam. Begin from the burner opening 17− Reinstall burner box, manifold assembly and burner boxSL280UHV NOX Inserts Repair Parts List Planned ServiceIntegrated Control Diagnostic Codes Integrated Control Diagnostic ModesFurnace / air handler. Clears after fault recovered Normal operation 5 seconds after fault recoveredPower at the thermostat. Alert stops all services Equipment is unable to communicate. IndicatesMissioning and Execute ’Set Factory Default mode’ Reconfigure the system. Replace control if heatingControl will still operate on default parameter set Ate feature will be set as ’installed’ and that couldSumes normal operation after fault is cleared Low pressure switch failed openFault is cleared Tion after fault is clearedOut. Clears when flame has been proven stable Open or not within specifications −hour soft lockSoft lockout or reset To flame failureIs not running. Check power to outdoor unit. Clears Pair/add duct. Cleared after the current service deError after current is sensed in both RUN Vice is removed, or after power resetSor run cycle, or after power reset Finished Program Unit Capacity/Size ModeCall for FIRST−STAGE Heat Troubleshooting Heating Sequence of OperationCall for Heat Satisfied Call for SECOND−STAGE Heat2ND Stage Heat Call for Heat Satisfied FIRST−STAGE Heat SECOND−STAGE HeatCall for Cooling Troubleshooting Cooling Sequence of OperationCall for FAN Troubleshooting Continuous Fan Sequence of Operation