Black & Decker WD4810N, WD9610N, WD9610ECN, WD7210N, DV9610PN manual Features, Installation

uNever attempt to charge nonrechargeable batteries.

uIf the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.

uDo not expose the charger to water.

uDo not open the charger.

uDo not probe the charger.

uThe appliance/tool/battery must be placed in a well venti- lated area when charging.

Safety of others

uThis appliance is not intended for use by persons (includ- ing children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concern- ing the use of the appliance by a person responsible for their safety.

uChildren should be supervised to ensure that they do not play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

uInjuries caused by touching any rotating/moving parts.

uInjuries caused when changing any parts, blades or accessories.

uInjuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks.

uImpairment of hearing.

uHealth hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF.)

Electrical safety

Your charger has been designed for a specific voltage. Always check that the mains voltage corresponds to the voltage on the rating plate. Never attempt to replace the charger unit with a regular mains plug.

Symbols on the charger

Read all of this manual carefully before using the # appliance.

This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

(Original instructions) ENGLISH

wShort circuit proof safety isolating transformer. The mains supply is electrically separated from the

x transformer output.

The charger automatically shuts off if the ambient temperature becomes too high. As a consequence the charger will be inoperable. The charging base must be disconnected from the mains supply and

$taken to an authorised service centre for repair. The charging base is intended for indoor use only.

Features

This tool includes some or all of the following features.

1.On/off switch

2.Bowl release button

3.Charging indicator

4.Charging socket (DV4800N, DV9610PN and WD9610ECN Only)

5.Dust bowl

6.Charger

7.Charging base (WD4810N, WD7210N and WD9610N Only)

Fig. A

8.Dry pick up cloth filter (DV4800N, DV9610PN Only)

9.Pre-filter (DV9610N Only)

10.Wet/Dry foam insert (WD4810N, WD7210N, WD9610ECN and WD9610N Only)

11.Wet/Dry deflector (WD4810N, WD7210N, WD9610ECN and WD9610N Only)

Fig. B

12.Squeegee (WD4810N, WD7210N, WD9610ECN and WD9610N Only)

13.Powered brush head (DV9610PN Only)

Installation

Wall Mounting (fig. C) (DV9610PN and WD9610ECN Only)

The product can be attached to a wall to provide a convenient storage and charging point for the appliance.

When fixing to a wall, make sure that the fixing method is suitable for the wall type and is appropriate to the weight of the appliance.

uMark the location of the screw holes (within reach of an electrical outlet for chargeing the vac while it is on the wall bracket).

uInsert the charger cord into the curved slot in the wall mount bracket leaving approximately 8-9 inches excess.

5