GE GNSH45E, GXSH39E Connect to Electrical Power, Programming the Control, SET Present Time of DAY

Page 10

Installation Instructions

10 CONNECT TO ELECTRICAL POWER

To gain access to the transformer/power cord assembly, remove the salt hole cover from the softener. Unclip the tabs on the rear of the top cover and rotate the cover upward to remove. DO NOT PULL OR DISCONNECT WIRING.

•The softener works on 24 volt-60Hz electric power. The included transformer changes standard 120-volt AC house power to 24 volts.

Plug the transformer into a 120-volt outlet only. Be sure the outlet is always live so it can not be switched off by mistake.

•Replace the top cover.

•Replace the salt hole cover.

PROGRAMMING THE CONTROL

PROGRAMMING THE CONTROL

CONTROL SETTINGS REQUIRED upon installation and after an extended power outage.

NOTES:

•WHEN THE TRANSFORMER IS PLUGGED INTO THE ELECTRICAL OUTLET, 12:00 PM (flashing), and an arrow is displayed next to PRESENT TIME on the faceplate decal. The blue indicator light will also flash. Program the control as instructed below.

If - - - is flashing, use the UP button

to set the correct F or P code as follows: P39 for

GXSH39E or P45 for GNSH45E. If you pass by the correct code number, use the DOWN button. Then press the MODE button to accept the correct model.

•A “beep” sounds while pressing buttons for control programming. One beep signals a change in the control display. Repeated beeps mean the control will not accept a change from the button you have pressed, and you should select another button.

•To program the control, you will use the UP , DOWN and MODE buttons.

•Use the MODE button to scroll arrow to desired control function.

SET PRESENT TIME OF DAY

1. Press the MODE button SALT

 

until arrow points to

LEVEL

PM

 

PRESENT TIME.

 

 

2.Press UP or DOWN

button to set. The UP button advances the time; the DOWN button moves the time in reverse.

. If the present time is between noon and midnight, be sure PM shows in the display. If the present time is between midnight and noon, be sure AM shows in the display.

NOTE: Each press of an UP or DOWN button changes the time by one minute. Holding the button changes the time at a rapid rate.

3.When the present time is correct, press MODE to accept.

SET WATER HARDNESS NUMBER

1. Press the MODE button SALT

LEVEL

until arrow points to

HARDNESS.

2.Press UP or DOWN

button to set your water hardness number in the display. DOWN decreases the hardness value. UP increases the hardness value.

NOTE: Each press of a button changes the display by 1, between 1 and 25. Above 25, the display changes 5 at a time (25, 30, 35, etc.). Holding a button in changes the numbers at a rapid rate.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 7283950 215C1173P025 49-50180-112-06 JR Safety InformationCare and Cleaning Write the model and serial numbers here Model #Safety Precautions Important Installation Recommendations Before Beginning InstallationRead these instructions completely and carefully Unpacking and Inspection Where to Install the SoftenerTransit Plan HOW YOU will Install the Softener OUTBefore YOU Begin Install Bypass ValveInstall Drain Fitting Push all the wayConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerInstall the Brine Tank Connecting a Rigid Valve Drain TubeADD Water and Salt to the Brine Tank Install Grounding ClampWith salt SET Present Time of DAY Connect to Electrical PowerProgramming the Control SET Water Hardness NumberSET Salt Level SET Recharge Starting TimeDays to Empty Optional Control Settings Feature Other Data DisplaysLOW Salt Signal SignalsLost Time Signal Error SignalsImportant Press and hold for 3 seconds Sanitizing Procedures19″ 471⁄2″ 411⁄4″ 16″ About the water softener system Cleaning the Nozzle and Venturi Assembly Breaking a Salt BridgeFeature/Service Automatic Electronic Diagnostics Feature Optional Recharge ControlsFeature Memory Normal Operation, Control DisplaysTo remove an error code 1. Unplug transformer Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure ERRService Set Model F or P Code Operation of DiagnosticsIf the water softening system does not draw brine, check Checking the Salt Storage Level and Refilling Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System However, you must keep the tank supplied with saltNo soft water Before you call for service…What To Do Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow Brown/yellow colored Water after installationSalty tasting or Colored water Resin beads showingPage Page Parts list 151 Parts catalog General Electric Parts CatalogSupport Screen For The Period We Will Replace What Is Not CoveredWarrantor General Electric Company. Louisville, KY Warrantor Mabe Canada INC GE Water Softening System Warranty. For Customers in CanadaOne Year De agua Cuidado y limpieza Cómo limpiar la ensambladuraDe averías Advertencia Advertencia No use con aguaRecomendaciones Importantes Para LA Instalación Lea estas instrucciones completa y cuidadosamenteDonde Instalar EL Descalcificador Desempacado E InspecciónHerramientas Y Materiales Necesarios Para LA Instalación Planifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalRemueva el tapón plástico de embalaje y el cable de la Antes DE ComenzarInstale LA Válvula DE Bypass Como se muestraRetire el descalcificador del lugar de instalación Cerciórese de cumplir con los códigos localesSalmuera Y LA Manguera Instale LOS Accesorios DESobreflujo DEL Tanque DE ContInstale LA Abrazadera DE Tierra Cierre todos los grifos de aguaAjuste LA Hora DEL DÍA Conectar a LA Fuente EléctricaProgramación DEL Control Hora actualDe recarga Ajuste EL Nivel DE SALDías Hasta Vacío De salCaracterística Otras Visualizaciones DE Datos Ajustes Opcionales DE ControlEficiencia DE LA SAL DEL SistemaSeñal DE Hora Perdida Señales DE ErrorSeñals Señal DE Bajo Nivel DE SALEn la fábrica se siguen los cuidados para mantener Procedimientos DE DesinfecciónNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Función Memoria Operación normal, Pantalla de controlFunción Controles opcionales de recargado Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Vea la sección Programación del controlServicio Configurar el código del modelo F o P Servicio Inspección manual del avance de la recargaCuidado y limpieza del sistema de descalcificación de agua Cuándo rellenar con sal Si una luz indicadoraAntes de llamar para solicitar servicio… Qué hacerVeces el agua Luz intermitente azul Lista de partes 151 Catálogo de partes Catálogo DE Partes DE General ElectricNO. Refer Por el período de Reemplazamos Garantía GE para el Sistema de Descalcificación de AguaLo que no está cubierto Garantías ampliadas Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Piezas y accesoriosConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Top Page Image Contents