KitchenAid 8564554 Install the door handle on some models, Pro Line Series, Option

Page 11

Install the door handle (on some models)

Install the door handle (on some models)

IMPORTANT: Do not scratch the front panel during this procedure.

1.Remove the Architect™ Series handle, plastic washers and two screws from handle package.

2.Attach the handle to the factory-supplied full front panel as shown.

film that is not to be removed

Pro Line™ Series

1.Remove the Pro Line™ Series handle and two screws from handle package.

2.Make sure plastic spacers are still attached to the door.

3.Attach the handle to the factory-supplied full front panel as shown.

plastic spacers

Install door panel (on some models)

Top vented models

NOTE: Features on your
dishwasher may differ
from model shown.	top vent

Option 1:

For Top vented models with a factory-supplied stainless or painted full front panel:

1.Remove the carton containing the factory-supplied full front panel.

2.Remove the handle package from the front of the shipping base.

3.Remove the inner panel from the door.

4.With a TORX® screwdriver, remove three screws from both sides of the door. Hold the inner panel up while removing the screws.

5.Gently set panel aside.

NOTE: Some models have 4 screws per side.

screws

	inner
screws	door	do not remove screw.
	panel	do not remove screw.

6.Lay the factory-supplied full front panel face down on a protective non-scratching surface.

7.Place the inner panel on the back of the full front panel as shown and attach, using the four #10-16 x 3/8" screws in the literature package.

4 screws

full front panel

inner door panel

top of panel

8.Attach the factory-supplied full front panel, inner panel, and handle assembly to the door.

9.Reinstall the two uppermost screws into the inner panel, do not tighten completely. This will hold the full front panel in place on the door frame.

2 screws

10.Install the two #8-18 x 1-3/8" screws from the literature package in the top corners of the door.

11.Align the top edge of the full front panel with the top edge of the console and secure corner screws.

12.Tighten the two screws installed in Step 9.

13.Reinstall and tighten the remaining screws in the inner panel.

2 screws

align top edges

11

Image 11

Contents Instrucciones de Instalación Lavavajillas empotrado HOME APPLIANCESInstallation Instructions Undercounter Dishwasher Instructions dinstallation Lave-vaisselle encastréTip Over Hazard Do not use dishwasher until completely installed Dishwasher SafetyTable of Contents Your safety and the safety of others are very importantTools and Parts Installation RequirementsAll installations In addition, for new installationsinsulation Product dimensionsCutout dimensions 24-7/8 63.2 cmWater Supply Requirements If direct wiring dishwasherIf connecting dishwasher with a power supply cord Drain RequirementsElectrical Shock Hazard Installation InstructionsPrepare cabinet opening using existing utility hookups Install the drain hoseOption 2 No waste disposer - with air gap Prepare cabinet opening where there are no existing utility hookupsOption1 Direct wire method Electrical connectionOption 2 Power supply cord method Install the water lineTip Over Hazard Excessive Weight HazardPrepare dishwasher If you have built-up floors Option Install the door handle on some modelsInstall door panel on some models Top vented models Pro Line SeriesTop vented models with a custom full front panel Front vented models Option 2 Dishwasher side attachment Choose attachment optionMove dishwasher into cabinet opening Option 1 Countertop attachmentLevel the dishwasher Option 1 Direct wire methodMake Electrical Connection Check door spring tensionDo not use an extension cord Connect ground wire to green ground connector in terminal boxConnect to water supply Electrical Shock Hazard Electrically ground dishwasherSecure dishwasher in cabinet opening Connect to drainPower supply cord method Bottom sound pad installation on some modelsComplete installation Direct wire methodIf dishwasher does not operate Check operation08/2004 Printed in U.S.AÍndice Seguridad de la lavavajillasPELIGRO ADVERTENCIA ADVERTENCIATodas las instalaciones Requisitos de instalaciónHerramientas y piezas Requisitos de ubicaciónVISTA POSTERIOR Dimensiones del productoDimensiones de corte VISTA LATERALSi está haciendo una conexión directa a la lavavajillas Requisitos de desagüeRequisitos del suministro de agua Requisitos eléctricosOpción 1, Recipiente de desechos - con espaciador de aire Instrucciones de instalaciónInstalación de la manguera de desagüe Peligro de Choque EléctricoOpción 3, Con recipiente de desechos - sin espaciador de aire Conexión eléctricaOpción 2, Sin recipiente de desechos - con espaciador de aire Opción 4. - Sin recipiente de desechos - sin espaciador de aireOpción 2, Método del cable de suministro de energía Instale la tubería de aguaInstale la manguera de desagüe Use dos o más personas para mover e instalar la lavavajillas Prepare la lavavajillasOpción 4, Sin recipiente de desechos - sin espaciador de aire Peligro de Peso Excesivo2. Ponga las ruedas en la Si tiene pisos armadosorificio Instalación de la manija de la puertaInstalación del panel de la puerta Modelos conNOTA La manija para el panel personalizado no se incluye dimensiones del panel personalizado Modelos con orificio de ventilación delanteromostrador Elija la opción para fijarMueva la lavavajillas hacia la abertura del gabinete Opción 1 Fijación alOpción 1.- Método de cableado directo Conexión eléctricaVerifique la tensión del resorte de la puerta Nivele la lavavajillasOpción 2 Método del cable de suministro de energía Conexión al suministro de aguaConecte a tierra la lavavajillas No use extensiónes eléctricasAsegure la lavavajillas en la abertura del gabinete Conexión al desagüeMétodo de conexión con cable de suministro de energía Instalación de la almohadilla inferior acústicaComplete la instalación Método de conexión con cable directoSi la lavavajillas no funciona Verifique el funcionamientoTable des matières Sécurité du lave-vaisselleDANGER AVERTISSEMENT AVERTISSEMENTOutillage et pièces Exigences d’installationEmplacement d’installation Pour toutes les configurations d’installationVUE ARRIÈRE Dimensions du produitDimensions de l’espace d’installation VUE LATÉRALEPour le raccordement direct du lave-vaisselle Spécifications de la canalisation d’évacuationSpécifications de l’alimentation en eau Spécifications électriquesOption 1 - broyeur à déchets - avec brise-siphon Instructions d’installationInstallation du tuyau d’évacuation Risque de choc électriqueOption 4 - pas de broyeur à déchets - sans brise-siphon Option 1 - raccordement direct emplacements préférés possiblesRaccordement électrique Option 2 - pas de broyeur à déchets - avec brise-siphonOption 2 - raccordement par cordon d’alimentation Installation de la canalisation d’eauRisque du poids excessif Préparation du lave-vaissellePlancher rehaussé Série Architect Installation de la poignée de porteInstallation du panneau de la porte Modèles à évacuation par le hautbord supérieur 76,7 cm 30-3/16interne de 25,2 cm 9-29/32devant Modèles à évent avantdimensions du panneau personnalisé Option Fixation sur le plan de travail Insertion du lave-vaisselle dans l’espace d’installationChoix de la méthode d’immobilisation de l’appareil Option 1 - Câblage direct Raccordement électriqueContrôle de la tension des ressorts de la porte Établissement de l’aplomb du lave-vaisselleOption 2 - Raccordement par cordon d’alimentation Raccordement à la canalisation d’eauRelier le lave-vaisselle à la terre d’une méthode électrique Ne pas utiliser un câble de rallongeRaccordement à la canalisation d’évacuation Immobilisation du lave-vaisselle dans l’espace d’installationAlimentation de l’appareil par cordon d’alimentation Installation du panneau d’insonorisationDernières opérations de l’installation Alimentation de l’appareil par câblage directSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnement