KitchenAid 8564554 installation instructions Front vented models

Page 13
Front vented models

16.Remove the two screws and the custom panel and drill two – 3/32" pilot holes 1/2" (13 mm) deep, where marked.

17.Reattach the custom panel, inner panel and handle assembly to the door.

18.Reinstall the two upper most screws into the inner panel. Do not tighten completely. This will hold the custom panel assembly in place on the door frame.

19.Install the two #8-18 x 1-3/8" screws from the literature package in the top corners of the door.

20.Align the top edge of the full front panel with the top edge of the console and secure corner screws.Tighten the two remaining screws installed in Step 18. Reinstall and tighten the remaining screws in the inner panel.

1-3/8"

 

screw

2 screws

 

align top edges

Front vented models

If the front of your dishwasher

looks like this, it is designed

for a custom panel.front vent

Model shown – KUDS01D_SP.

All other models require an accessory option to attach custom panels.

NOTE: A custom front panel must weigh no more than 14 pounds (6.3 kg) and must be

made to these dimensions. It is recommended that a cabinetmaker cut the custom panel because of precise dimensions needed.

IMPORTANT: Use a moisture resistant sealer on both sides and all edges of panel to protect from humidity.

NOTE: These dimensions are for frameless custom panel models with a 4-inch (10.2 cm) console only.

1/8" (3.2 mm)

custom panel

dimensions

1/8" Manual background (3.2 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front View

 

 

*25

-

29/32"

 

 

 

Side View

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(65.8

cm)

 

 

 

 

 

 

 

 

 

 

front

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23-3/8"

 

 

 

3/4"

 

 

 

 

 

 

 

 

 

(59.4 cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1.9 cm)

 

 

 

 

 

 

 

 

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

1.To install the custom panel, first remove metal front panel from door.

2.With TORX® screwdriver, remove lower three screws from both sides of inner door.

3.Hold panel up while removing screws.

NOTE: Some models have four screws per side.

3 screws

3 screws

front panel

4.Lay metal panel on back of custom panel.

5.Align top edge of custom panel with top edge of metal panel, and center it side to side.

6.Mark the position of four inner holes on custom panel.

4 inner holes

custom panel

metal panel

7.Drill four 3/32" holes in custom panel at marked positions.

8.Attach custom panel to metal panel with four #10 x 1/2" wood screws (not supplied). (If the custom panel is less than 3/4" (1.9 cm) thick where the screws are attached, shorter screws may be required.)

9.Reattach the assembled panels to dishwasher door.

13

Image 13
Contents Installation Instructions Undercounter Dishwasher HOME APPLIANCESInstructions dinstallation Lave-vaisselle encastré Instrucciones de Instalación Lavavajillas empotradoTable of Contents Dishwasher SafetyYour safety and the safety of others are very important Tip Over Hazard Do not use dishwasher until completely installedAll installations Installation RequirementsIn addition, for new installations Tools and PartsCutout dimensions Product dimensions24-7/8 63.2 cm insulationIf connecting dishwasher with a power supply cord If direct wiring dishwasherDrain Requirements Water Supply RequirementsPrepare cabinet opening using existing utility hookups Installation InstructionsInstall the drain hose Electrical Shock HazardOption1 Direct wire method Prepare cabinet opening where there are no existing utility hookupsElectrical connection Option 2 No waste disposer - with air gapOption 2 Power supply cord method Install the water linePrepare dishwasher Excessive Weight HazardTip Over Hazard If you have built-up floors Install door panel on some models Top vented models Install the door handle on some modelsPro Line Series OptionTop vented models with a custom full front panel Front vented models Move dishwasher into cabinet opening Choose attachment optionOption 1 Countertop attachment Option 2 Dishwasher side attachmentMake Electrical Connection Option 1 Direct wire methodCheck door spring tension Level the dishwasherConnect to water supply Connect ground wire to green ground connector in terminal boxElectrical Shock Hazard Electrically ground dishwasher Do not use an extension cordSecure dishwasher in cabinet opening Connect to drainComplete installation Bottom sound pad installation on some modelsDirect wire method Power supply cord methodIf dishwasher does not operate Check operation08/2004 Printed in U.S.APELIGRO ADVERTENCIA Seguridad de la lavavajillasADVERTENCIA ÍndiceHerramientas y piezas Requisitos de instalaciónRequisitos de ubicación Todas las instalacionesDimensiones de corte Dimensiones del productoVISTA LATERAL VISTA POSTERIORRequisitos del suministro de agua Requisitos de desagüeRequisitos eléctricos Si está haciendo una conexión directa a la lavavajillasInstalación de la manguera de desagüe Instrucciones de instalaciónPeligro de Choque Eléctrico Opción 1, Recipiente de desechos - con espaciador de aireOpción 2, Sin recipiente de desechos - con espaciador de aire Conexión eléctricaOpción 4. - Sin recipiente de desechos - sin espaciador de aire Opción 3, Con recipiente de desechos - sin espaciador de aireInstale la manguera de desagüe Instale la tubería de aguaOpción 2, Método del cable de suministro de energía Opción 4, Sin recipiente de desechos - sin espaciador de aire Prepare la lavavajillasPeligro de Peso Excesivo Use dos o más personas para mover e instalar la lavavajillas2. Ponga las ruedas en la Si tiene pisos armadosInstalación del panel de la puerta Instalación de la manija de la puertaModelos con orificioNOTA La manija para el panel personalizado no se incluye dimensiones del panel personalizado Modelos con orificio de ventilación delanteroMueva la lavavajillas hacia la abertura del gabinete Elija la opción para fijarOpción 1 Fijación al mostradorVerifique la tensión del resorte de la puerta Conexión eléctricaNivele la lavavajillas Opción 1.- Método de cableado directoConecte a tierra la lavavajillas Conexión al suministro de aguaNo use extensiónes eléctricas Opción 2 Método del cable de suministro de energíaAsegure la lavavajillas en la abertura del gabinete Conexión al desagüeComplete la instalación Instalación de la almohadilla inferior acústicaMétodo de conexión con cable directo Método de conexión con cable de suministro de energíaSi la lavavajillas no funciona Verifique el funcionamientoDANGER AVERTISSEMENT Sécurité du lave-vaisselleAVERTISSEMENT Table des matièresEmplacement d’installation Exigences d’installationPour toutes les configurations d’installation Outillage et piècesDimensions de l’espace d’installation Dimensions du produitVUE LATÉRALE VUE ARRIÈRESpécifications de l’alimentation en eau Spécifications de la canalisation d’évacuationSpécifications électriques Pour le raccordement direct du lave-vaisselleInstallation du tuyau d’évacuation Instructions d’installationRisque de choc électrique Option 1 - broyeur à déchets - avec brise-siphonRaccordement électrique Option 1 - raccordement direct emplacements préférés possiblesOption 2 - pas de broyeur à déchets - avec brise-siphon Option 4 - pas de broyeur à déchets - sans brise-siphonOption 2 - raccordement par cordon d’alimentation Installation de la canalisation d’eauRisque du poids excessif Préparation du lave-vaissellePlancher rehaussé Installation du panneau de la porte Installation de la poignée de porteModèles à évacuation par le haut Série Architectinterne de 76,7 cm 30-3/1625,2 cm 9-29/32 bord supérieurdimensions du panneau personnalisé Modèles à évent avantdevant Choix de la méthode d’immobilisation de l’appareil Insertion du lave-vaisselle dans l’espace d’installationOption Fixation sur le plan de travail Contrôle de la tension des ressorts de la porte Raccordement électriqueÉtablissement de l’aplomb du lave-vaisselle Option 1 - Câblage directRelier le lave-vaisselle à la terre d’une méthode électrique Raccordement à la canalisation d’eauNe pas utiliser un câble de rallonge Option 2 - Raccordement par cordon d’alimentationRaccordement à la canalisation d’évacuation Immobilisation du lave-vaisselle dans l’espace d’installationDernières opérations de l’installation Installation du panneau d’insonorisationAlimentation de l’appareil par câblage direct Alimentation de l’appareil par cordon d’alimentationSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnement