KitchenAid 8564554 Installation Instructions, Install the drain hose, Electrical Shock Hazard

Page 6
Installation Instructions

Installation Instructions

Electrical Shock HazardWARNING

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1.Disconnect power.

2.Turn off water supply.

Prepare cabinet opening using existing utility hookups

Follow the steps in this section if you are installing the dishwasher in an existing cabinet opening with utility hookups.

If you are installing the dishwasher in a cabinet opening that does not have hookups, follow the steps under "Prepare cabinet opening where there are no existing utility hookups" section.

Install the drain hose

IMPORTANT: Always use a new drain hose even when installing a new replacement dishwasher.

1.Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink.

2.Connect drain hose to waste tee or waste disposer using one of the following methods:

Option 1, Waste disposer – with air gap

Option 2, No waste disposer – with air gap

Option 3, Waste disposer – no air gap*

Option 4, No waste disposer – no air gap*

*an air gap is recommended

Helpful Tip: To reduce the vibration of the hose, keep the hose away from the floor and the edge of the hole where it passes through the cabinet.

Option 1: Waste disposer – with air gap:

1. Remove the disposer knockout plug. Cut end of drain

hose if needed (do not cut ribbed section).

2. Attach drain hose to air gap with large spring-type

clamp. If the drain hose was cut, use a 1-1/2" to 2"

(3.8 to 5 cm) screw-type clamp*.

1.Check that the water line reaches to the front left of opening where the water connection will be made.

2.Check that the direct wire reaches to the front right of opening where the electrical connection will be made.

water line

direct wire

6" (15.2 cm)

3. Use a rubber hose connector* with spring or screw-

type clamps* to connect air gap to disposer inlet.

This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher

will be installed.

drain hose –

 

cut here if needed

 

rubber hose

 

connector

air gap

 

spring or

 

If the water line and the direct wire reach far enough into the opening, proceed to the next section “Install the drain hose.“ If they do not reach far enough, follow the steps under “Prepare cabinet opening where there are no existing utility hookups.”

screw-type

 

large

clamps

 

 

spring-type

 

 

 

 

clamp

 

disposer

drain

 

hose

 

inlet

 

 

drain trap

 

 

4. Insert drain hose

drain hose

 

through hole cut in

 

 

cabinet to the front

 

 

center of opening where

 

 

drain connection will be

 

 

made.

 

 

* Parts available from local plumbing supply stores

6

Image 6
Contents Instructions dinstallation Lave-vaisselle encastré HOME APPLIANCESInstallation Instructions Undercounter Dishwasher Instrucciones de Instalación Lavavajillas empotradoYour safety and the safety of others are very important Dishwasher SafetyTable of Contents Tip Over Hazard Do not use dishwasher until completely installedIn addition, for new installations Installation RequirementsAll installations Tools and Parts24-7/8 63.2 cm Product dimensionsCutout dimensions insulationDrain Requirements If direct wiring dishwasherIf connecting dishwasher with a power supply cord Water Supply RequirementsInstall the drain hose Installation InstructionsPrepare cabinet opening using existing utility hookups Electrical Shock HazardElectrical connection Prepare cabinet opening where there are no existing utility hookupsOption1 Direct wire method Option 2 No waste disposer - with air gapInstall the water line Option 2 Power supply cord methodExcessive Weight Hazard Prepare dishwasherTip Over Hazard If you have built-up floors Pro Line Series Install the door handle on some modelsInstall door panel on some models Top vented models OptionTop vented models with a custom full front panel Front vented models Option 1 Countertop attachment Choose attachment optionMove dishwasher into cabinet opening Option 2 Dishwasher side attachmentCheck door spring tension Option 1 Direct wire methodMake Electrical Connection Level the dishwasherElectrical Shock Hazard Electrically ground dishwasher Connect ground wire to green ground connector in terminal boxConnect to water supply Do not use an extension cordConnect to drain Secure dishwasher in cabinet openingDirect wire method Bottom sound pad installation on some modelsComplete installation Power supply cord methodCheck operation If dishwasher does not operatePrinted in U.S.A 08/2004ADVERTENCIA Seguridad de la lavavajillasPELIGRO ADVERTENCIA ÍndiceRequisitos de ubicación Requisitos de instalaciónHerramientas y piezas Todas las instalacionesVISTA LATERAL Dimensiones del productoDimensiones de corte VISTA POSTERIORRequisitos eléctricos Requisitos de desagüeRequisitos del suministro de agua Si está haciendo una conexión directa a la lavavajillasPeligro de Choque Eléctrico Instrucciones de instalaciónInstalación de la manguera de desagüe Opción 1, Recipiente de desechos - con espaciador de aireOpción 4. - Sin recipiente de desechos - sin espaciador de aire Conexión eléctricaOpción 2, Sin recipiente de desechos - con espaciador de aire Opción 3, Con recipiente de desechos - sin espaciador de aireInstale la tubería de agua Instale la manguera de desagüeOpción 2, Método del cable de suministro de energía Peligro de Peso Excesivo Prepare la lavavajillasOpción 4, Sin recipiente de desechos - sin espaciador de aire Use dos o más personas para mover e instalar la lavavajillasSi tiene pisos armados 2. Ponga las ruedas en laModelos con Instalación de la manija de la puertaInstalación del panel de la puerta orificioNOTA La manija para el panel personalizado no se incluye Modelos con orificio de ventilación delantero dimensiones del panel personalizadoOpción 1 Fijación al Elija la opción para fijarMueva la lavavajillas hacia la abertura del gabinete mostradorNivele la lavavajillas Conexión eléctricaVerifique la tensión del resorte de la puerta Opción 1.- Método de cableado directoNo use extensiónes eléctricas Conexión al suministro de aguaConecte a tierra la lavavajillas Opción 2 Método del cable de suministro de energíaConexión al desagüe Asegure la lavavajillas en la abertura del gabineteMétodo de conexión con cable directo Instalación de la almohadilla inferior acústicaComplete la instalación Método de conexión con cable de suministro de energíaVerifique el funcionamiento Si la lavavajillas no funcionaAVERTISSEMENT Sécurité du lave-vaisselleDANGER AVERTISSEMENT Table des matièresPour toutes les configurations d’installation Exigences d’installationEmplacement d’installation Outillage et piècesVUE LATÉRALE Dimensions du produitDimensions de l’espace d’installation VUE ARRIÈRESpécifications électriques Spécifications de la canalisation d’évacuationSpécifications de l’alimentation en eau Pour le raccordement direct du lave-vaisselleRisque de choc électrique Instructions d’installationInstallation du tuyau d’évacuation Option 1 - broyeur à déchets - avec brise-siphonOption 2 - pas de broyeur à déchets - avec brise-siphon Option 1 - raccordement direct emplacements préférés possiblesRaccordement électrique Option 4 - pas de broyeur à déchets - sans brise-siphonInstallation de la canalisation d’eau Option 2 - raccordement par cordon d’alimentationPréparation du lave-vaisselle Risque du poids excessifPlancher rehaussé Modèles à évacuation par le haut Installation de la poignée de porteInstallation du panneau de la porte Série Architect25,2 cm 9-29/32 76,7 cm 30-3/16interne de bord supérieurModèles à évent avant dimensions du panneau personnalisédevant Insertion du lave-vaisselle dans l’espace d’installation Choix de la méthode d’immobilisation de l’appareilOption Fixation sur le plan de travail Établissement de l’aplomb du lave-vaisselle Raccordement électriqueContrôle de la tension des ressorts de la porte Option 1 - Câblage directNe pas utiliser un câble de rallonge Raccordement à la canalisation d’eauRelier le lave-vaisselle à la terre d’une méthode électrique Option 2 - Raccordement par cordon d’alimentationImmobilisation du lave-vaisselle dans l’espace d’installation Raccordement à la canalisation d’évacuationAlimentation de l’appareil par câblage direct Installation du panneau d’insonorisationDernières opérations de l’installation Alimentation de l’appareil par cordon d’alimentationContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctement