KitchenAid 8564554 Prepare dishwasher, Tip Over Hazard, Excessive Weight Hazard

Page 9
Prepare dishwasher

Option 2: No waste disposer – with air gap:

1.Cut end of drain hose if needed (do not cut ribbed section).

2.Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*.

3.Use a rubber hose connector* with spring or screw- type clamps* to connect air gap to waste tee.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed.

drain hose –

cut here if needed

rubber hose

connector

air gap

Option 4: No waste disposer – no air gap:

1.Cut end of drain hose if needed (do not cut ribbed section).

2.Attach drain hose to waste tee with 1-1/2" to 2"

(3.8 to 5 cm) screw-type clamp*.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose be looped up and securely fastened to the underside of the counter.

drain hose – Tip Over Hazard cut here if needed

screw-type clamp

spring or screw-type clamps

 

waste

drain trap

tee

 

large spring-type Excessive Weight Hazard clamp

drain hose

waste tee

drain hose

drain trap

4. Insert drain hose

 

 

drain hose

through hole cut in

 

 

 

 

 

 

 

 

cabinet to the front

 

 

 

 

 

 

 

 

 

 

 

 

center of opening where

 

 

 

 

 

 

 

 

 

 

 

 

drain connection will be

 

 

 

 

 

 

made.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* Parts available from local plumbing supply stores

Option 3: Waste disposer – no air gap:

1.Remove the disposer knockout plug. Do not cut end of drain hose.

2.Attach drain hose to disposer inlet with large spring- type clamp.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose be looped up and securely fastened to the underside of the counter.

large spring-type clamp

drain hose

disposer inlet

drain trap

 

3. Insert drain hose

drain hose

through hole cut in

 

cabinet to the front

 

center of opening where

 

drain connection will be

 

made.

 

3. Insert drain hose

drain hose

through hole cut in

 

cabinet to the front

 

center of opening where

 

drain connection will be

 

made.

 

* Parts available from local plumbing supply stores

Prepare dishwasher

Manual backgroundWARNING

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

Manual backgroundWARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury.

1.Put corner posts from packaging behind dishwasher. Grasp sides of dishwasher door frame and put dishwasher on its back, resting on top of the corner posts.

9

Image 9
Contents Installation Instructions Undercounter Dishwasher HOME APPLIANCESInstructions dinstallation Lave-vaisselle encastré Instrucciones de Instalación Lavavajillas empotradoTable of Contents Dishwasher SafetyYour safety and the safety of others are very important Tip Over Hazard Do not use dishwasher until completely installedAll installations Installation RequirementsIn addition, for new installations Tools and PartsCutout dimensions Product dimensions24-7/8 63.2 cm insulationIf connecting dishwasher with a power supply cord If direct wiring dishwasherDrain Requirements Water Supply RequirementsPrepare cabinet opening using existing utility hookups Installation InstructionsInstall the drain hose Electrical Shock HazardOption1 Direct wire method Prepare cabinet opening where there are no existing utility hookupsElectrical connection Option 2 No waste disposer - with air gapOption 2 Power supply cord method Install the water lineExcessive Weight Hazard Prepare dishwasherTip Over Hazard If you have built-up floors Install door panel on some models Top vented models Install the door handle on some modelsPro Line Series OptionTop vented models with a custom full front panel Front vented models Move dishwasher into cabinet opening Choose attachment optionOption 1 Countertop attachment Option 2 Dishwasher side attachmentMake Electrical Connection Option 1 Direct wire methodCheck door spring tension Level the dishwasherConnect to water supply Connect ground wire to green ground connector in terminal boxElectrical Shock Hazard Electrically ground dishwasher Do not use an extension cordSecure dishwasher in cabinet opening Connect to drainComplete installation Bottom sound pad installation on some modelsDirect wire method Power supply cord methodIf dishwasher does not operate Check operation08/2004 Printed in U.S.APELIGRO ADVERTENCIA Seguridad de la lavavajillasADVERTENCIA ÍndiceHerramientas y piezas Requisitos de instalaciónRequisitos de ubicación Todas las instalacionesDimensiones de corte Dimensiones del productoVISTA LATERAL VISTA POSTERIORRequisitos del suministro de agua Requisitos de desagüeRequisitos eléctricos Si está haciendo una conexión directa a la lavavajillasInstalación de la manguera de desagüe Instrucciones de instalaciónPeligro de Choque Eléctrico Opción 1, Recipiente de desechos - con espaciador de aireOpción 2, Sin recipiente de desechos - con espaciador de aire Conexión eléctricaOpción 4. - Sin recipiente de desechos - sin espaciador de aire Opción 3, Con recipiente de desechos - sin espaciador de aireInstale la tubería de agua Instale la manguera de desagüeOpción 2, Método del cable de suministro de energía Opción 4, Sin recipiente de desechos - sin espaciador de aire Prepare la lavavajillasPeligro de Peso Excesivo Use dos o más personas para mover e instalar la lavavajillas2. Ponga las ruedas en la Si tiene pisos armadosInstalación del panel de la puerta Instalación de la manija de la puertaModelos con orificioNOTA La manija para el panel personalizado no se incluye dimensiones del panel personalizado Modelos con orificio de ventilación delanteroMueva la lavavajillas hacia la abertura del gabinete Elija la opción para fijarOpción 1 Fijación al mostradorVerifique la tensión del resorte de la puerta Conexión eléctricaNivele la lavavajillas Opción 1.- Método de cableado directoConecte a tierra la lavavajillas Conexión al suministro de aguaNo use extensiónes eléctricas Opción 2 Método del cable de suministro de energíaAsegure la lavavajillas en la abertura del gabinete Conexión al desagüeComplete la instalación Instalación de la almohadilla inferior acústicaMétodo de conexión con cable directo Método de conexión con cable de suministro de energíaSi la lavavajillas no funciona Verifique el funcionamientoDANGER AVERTISSEMENT Sécurité du lave-vaisselleAVERTISSEMENT Table des matièresEmplacement d’installation Exigences d’installationPour toutes les configurations d’installation Outillage et piècesDimensions de l’espace d’installation Dimensions du produitVUE LATÉRALE VUE ARRIÈRESpécifications de l’alimentation en eau Spécifications de la canalisation d’évacuationSpécifications électriques Pour le raccordement direct du lave-vaisselleInstallation du tuyau d’évacuation Instructions d’installationRisque de choc électrique Option 1 - broyeur à déchets - avec brise-siphonRaccordement électrique Option 1 - raccordement direct emplacements préférés possiblesOption 2 - pas de broyeur à déchets - avec brise-siphon Option 4 - pas de broyeur à déchets - sans brise-siphonOption 2 - raccordement par cordon d’alimentation Installation de la canalisation d’eauRisque du poids excessif Préparation du lave-vaissellePlancher rehaussé Installation du panneau de la porte Installation de la poignée de porteModèles à évacuation par le haut Série Architectinterne de 76,7 cm 30-3/1625,2 cm 9-29/32 bord supérieurModèles à évent avant dimensions du panneau personnalisédevant Insertion du lave-vaisselle dans l’espace d’installation Choix de la méthode d’immobilisation de l’appareilOption Fixation sur le plan de travail Contrôle de la tension des ressorts de la porte Raccordement électriqueÉtablissement de l’aplomb du lave-vaisselle Option 1 - Câblage directRelier le lave-vaisselle à la terre d’une méthode électrique Raccordement à la canalisation d’eauNe pas utiliser un câble de rallonge Option 2 - Raccordement par cordon d’alimentationRaccordement à la canalisation d’évacuation Immobilisation du lave-vaisselle dans l’espace d’installationDernières opérations de l’installation Installation du panneau d’insonorisationAlimentation de l’appareil par câblage direct Alimentation de l’appareil par cordon d’alimentationSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnement