KitchenAid 8564554 Prepare cabinet opening where there are no existing utility hookups

Page 7
Option 2: No waste disposer – with air gap:

Option 2: No waste disposer – with air gap:

1.Cut end of drain hose if needed (do not cut ribbed section).

2.Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*.

3.Use a rubber hose connector* with spring or screw- type clamps* to connect air gap to waste tee.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed.

drain hose – Option 4: No waste disposer – no air gap: cut here if needed

rubber hose

connector

air gap

Option 4: No waste disposer – no air gap:

1.Cut end of drain hose if needed (do not cut ribbed section).

2.Attach drain hose to waste tee with 1-1/2" to 2"

(3.8 to 5 cm) screw-type clamp*.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose be looped up and securely fastened to the underside of the counter.

drain hose – Option 3: Waste disposer – no air gap: cut here if needed

screw-type clamp

spring or screw-type clamps

 

waste

drain trap

tee

 

large spring-type Prepare cabinet opening where there are no existing utility hookups clamp

drain hose

waste tee

drain hose

drain trap

4. Insert drain hose

 

 

 

drain hose

through hole cut in

 

 

 

 

 

 

 

cabinet to the front

 

 

 

 

 

 

 

 

 

 

 

 

center of opening where

 

 

 

 

 

 

 

 

 

 

 

 

 

 

drain connection will be

 

 

 

 

 

 

 

made.

 

 

 

 

 

 

 

 

 

 

 

 

 

* Parts available from local plumbing supply stores

Option 3: Waste disposer – no air gap:

1.Remove the disposer knockout plug. Do not cut end of drain hose.

2.Attach drain hose to disposer inlet with large spring- type clamp.

This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. It is recommended that the drain hose be looped up and securely fastened to the underside of

the counter.

large spring-type clamp

drain hose

disposer inlet

drain trap

 

3. Insert drain hose

drain hose

through hole cut in

 

cabinet to the front

 

center of opening where

 

drain connection will be

 

made.

 

3. Insert drain hose

drain hose

through hole cut in

 

cabinet to the front

 

center of opening where

 

drain connection will be

 

made.

 

* Parts available from local plumbing supply stores

Prepare cabinet opening where there are no existing utility hookups

Electrical connection

Option1: Direct wire method:

Helpful Tip: Wiring the dishwasher will be easier if you route wire into the cabinet opening from the right side.

1. Drill a 3/4" (1.9 cm)

optional

preferred

hole in right-hand

locations

locations

cabinet side, rear or

 

 

 

 

 

 

floor. Preferred and

 

 

 

 

 

 

optional locations are

 

 

 

 

 

 

shown.

 

 

 

 

 

 

 

 

 

 

 

 

2. Wood cabinet: Sand hole until smooth.

Metal cabinet: Cover

hole with grommet, not provided.

3.Run wire into house wiring junction box.

4.Install a U.L.-listed/CSA-certified clamp connector (strain relief) for flexible-type wire. If installing conduit, attach a U.L.-listed/CSA-certified conduit connector to the junction box.

5.Run other end of wire

through cabinet hole. Cable must extend to the right front of cabinet opening.

7

Image 7
Contents Instrucciones de Instalación Lavavajillas empotrado HOME APPLIANCESInstallation Instructions Undercounter Dishwasher Instructions dinstallation Lave-vaisselle encastréTip Over Hazard Do not use dishwasher until completely installed Dishwasher SafetyTable of Contents Your safety and the safety of others are very importantTools and Parts Installation RequirementsAll installations In addition, for new installationsinsulation Product dimensionsCutout dimensions 24-7/8 63.2 cmWater Supply Requirements If direct wiring dishwasherIf connecting dishwasher with a power supply cord Drain RequirementsElectrical Shock Hazard Installation InstructionsPrepare cabinet opening using existing utility hookups Install the drain hoseOption 2 No waste disposer - with air gap Prepare cabinet opening where there are no existing utility hookupsOption1 Direct wire method Electrical connectionOption 2 Power supply cord method Install the water linePrepare dishwasher Excessive Weight HazardTip Over Hazard If you have built-up floors Option Install the door handle on some modelsInstall door panel on some models Top vented models Pro Line SeriesTop vented models with a custom full front panel Front vented models Option 2 Dishwasher side attachment Choose attachment optionMove dishwasher into cabinet opening Option 1 Countertop attachmentLevel the dishwasher Option 1 Direct wire methodMake Electrical Connection Check door spring tensionDo not use an extension cord Connect ground wire to green ground connector in terminal boxConnect to water supply Electrical Shock Hazard Electrically ground dishwasherSecure dishwasher in cabinet opening Connect to drainPower supply cord method Bottom sound pad installation on some modelsComplete installation Direct wire methodIf dishwasher does not operate Check operation08/2004 Printed in U.S.AÍndice Seguridad de la lavavajillasPELIGRO ADVERTENCIA ADVERTENCIATodas las instalaciones Requisitos de instalaciónHerramientas y piezas Requisitos de ubicaciónVISTA POSTERIOR Dimensiones del productoDimensiones de corte VISTA LATERALSi está haciendo una conexión directa a la lavavajillas Requisitos de desagüeRequisitos del suministro de agua Requisitos eléctricosOpción 1, Recipiente de desechos - con espaciador de aire Instrucciones de instalaciónInstalación de la manguera de desagüe Peligro de Choque EléctricoOpción 3, Con recipiente de desechos - sin espaciador de aire Conexión eléctricaOpción 2, Sin recipiente de desechos - con espaciador de aire Opción 4. - Sin recipiente de desechos - sin espaciador de aireInstale la manguera de desagüe Instale la tubería de aguaOpción 2, Método del cable de suministro de energía Use dos o más personas para mover e instalar la lavavajillas Prepare la lavavajillasOpción 4, Sin recipiente de desechos - sin espaciador de aire Peligro de Peso Excesivo2. Ponga las ruedas en la Si tiene pisos armadosorificio Instalación de la manija de la puertaInstalación del panel de la puerta Modelos conNOTA La manija para el panel personalizado no se incluye dimensiones del panel personalizado Modelos con orificio de ventilación delanteromostrador Elija la opción para fijarMueva la lavavajillas hacia la abertura del gabinete Opción 1 Fijación alOpción 1.- Método de cableado directo Conexión eléctricaVerifique la tensión del resorte de la puerta Nivele la lavavajillasOpción 2 Método del cable de suministro de energía Conexión al suministro de aguaConecte a tierra la lavavajillas No use extensiónes eléctricasAsegure la lavavajillas en la abertura del gabinete Conexión al desagüeMétodo de conexión con cable de suministro de energía Instalación de la almohadilla inferior acústicaComplete la instalación Método de conexión con cable directoSi la lavavajillas no funciona Verifique el funcionamientoTable des matières Sécurité du lave-vaisselleDANGER AVERTISSEMENT AVERTISSEMENTOutillage et pièces Exigences d’installationEmplacement d’installation Pour toutes les configurations d’installationVUE ARRIÈRE Dimensions du produitDimensions de l’espace d’installation VUE LATÉRALEPour le raccordement direct du lave-vaisselle Spécifications de la canalisation d’évacuationSpécifications de l’alimentation en eau Spécifications électriquesOption 1 - broyeur à déchets - avec brise-siphon Instructions d’installationInstallation du tuyau d’évacuation Risque de choc électriqueOption 4 - pas de broyeur à déchets - sans brise-siphon Option 1 - raccordement direct emplacements préférés possiblesRaccordement électrique Option 2 - pas de broyeur à déchets - avec brise-siphonOption 2 - raccordement par cordon d’alimentation Installation de la canalisation d’eauRisque du poids excessif Préparation du lave-vaissellePlancher rehaussé Série Architect Installation de la poignée de porteInstallation du panneau de la porte Modèles à évacuation par le hautbord supérieur 76,7 cm 30-3/16interne de 25,2 cm 9-29/32dimensions du panneau personnalisé Modèles à évent avantdevant Choix de la méthode d’immobilisation de l’appareil Insertion du lave-vaisselle dans l’espace d’installationOption Fixation sur le plan de travail Option 1 - Câblage direct Raccordement électriqueContrôle de la tension des ressorts de la porte Établissement de l’aplomb du lave-vaisselleOption 2 - Raccordement par cordon d’alimentation Raccordement à la canalisation d’eauRelier le lave-vaisselle à la terre d’une méthode électrique Ne pas utiliser un câble de rallongeRaccordement à la canalisation d’évacuation Immobilisation du lave-vaisselle dans l’espace d’installationAlimentation de l’appareil par cordon d’alimentation Installation du panneau d’insonorisationDernières opérations de l’installation Alimentation de l’appareil par câblage directSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnement