Frymaster H52 Series warranty Probe Failure Indication

Page 20

alarm continues flashing. All functions return when the frypot temperature is within 15°F (8°C) of the programmed setpoint.

Probe Failure Indication

If the temperature probe fails, the display will flash PROBE FAILURE and an audible alarm will sound. To cancel the alarm, turn the computer OFF. In split-vat fryers, turn off the side in which the failure occurred. If a probe fails during the high-limit test, PROBE FAILURE is displayed.

NOTE: If the temperature probe fails in the left side of a split-vat, that side cannot be turned back ON once it has been turned OFF.

3.6M-100B™ Computer Set-Up and Programming Instructions

The M-100B computer has three modes of operation. In addition to the Cooking Mode, which was discussed in Sections 3.3 and 3.4, there is a Setup Mode and a Programming Mode. (The cooking mode is the computer’s default mode – when the computer is turned on, it comes up in the cooking mode.)

In the Setup Mode, the operator can:

change the computer’s display language

configure the computer for use on gas fryers

configure the computer for use on either a full-vat or a split-vat fryer

specify how the computer displays product names and temperatures

calibrate computer temperature to actual frypot temperature

activate or deactivate the frypot BOIL OUT feature

In the Program Mode, the operator can:

reset the computer to the factory default settings

change the shake, pull, and QA (hold) times for menu items

change the cooking temperature setpoints for menu items

add products and cooking parameters to the two test menus

suppress a duty function in a menu item

turn the display of a menu item in the factory-programmed menu on or off

display usage information that is automatically recorded by the computer

3–7

Image 20
Contents OPERATOR’S Manual Frymaster H52 Series GAS Fryer Page Introduction GeneralWhat to do if your equipment arrives damaged Computer InformationEuropean Community CE Specific Information Service Information Installation Instructions General Installation RequirementsNational Code Requirements Caster/Leg Installation Non-CE Standard For Incoming Gas Pressures Connection to Gas Line Countries Categories GASCE Standard Converting to Another Gas Type Gas VatFrypot Boil-Out Non-CE Gas Conversion KitsCE Gas Conversion Kits for Units with Gas Valve Operating Fryers With M100B Cooking Computers ShutdownIntroduction To The M-100B Cooking Computer DescriptionOperating the Computer on Full-Vat Fryers Cooking Product Full-Vat or Split-Vat Viewing the Frypot Temperature Actual or SetpointOperating the Computer on Split-Vat Fryers M-100B Computer Problem Condition Indicators Recovery Out of Range REC LockOpen Drain Valve Indication Probe Failure Indication M-100B Computer Set-Up and Programming Instructions1 M-100B Computer Setup Mode How to Enter the Setup ModeHow to Change the Computer’s Display Language How to Configure the Computer for Use on a Gas FryerHow to Change Computer Product/Temperature Displays How to Activate or Deactivate the Frypot BOIL-OUT Feature 2 M-100B Computer Programming ModeHow to Enter the Program Mode How to Reset the Computer to the Factory DefaultsHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display Use Time Information How to Display the Product Cycle Accumulator InformationHow to Use the Filter Countdown Timer Operating Fryers With Analog Controllers Introduction to the Analog ControllerC D E F G H I J K L M N Analog Controller High-Limit Check Page Filtering Operating the Built-In Filtration System Page Operating the Filter Unit Page Getting the Most Out of Your Filter Page Troubleshooting Preventive Maintenance and TroubleshootingPreventive Maintenance Troubleshooting Fryers with M100B Computers REC LockIgnition Failure Display Remains Blank When ON/OFF Switches are Pressed Troubleshooting Fryers Equipped with Analog Controllers Did burners Troubleshooting Built-in Filtration System Pump does Not RUN