Frymaster H52 Series warranty How to Display Use Time Information

Page 27

4.Use the cook switches 1 , 2 , 1 from left to right to set the time display to read 000. This will suppress the function during the cooking cycle. To reactivate the function, follow steps 1 through 3 to enter a time for the function.

5.Exit the program mode by pressing the right switch.

How to Turn the Display of a Factory-Programmed Menu Item On and Off

1.Enter the program mode. See How to Enter the Program Mode on Page 3-10.

2.Press and release the switch until the menu item to be turned on or off is displayed in the left window.

3.The right display will show YES or NO. To turn the menu item OFF, press either of the right

1or 2 switches to set the option to NO. To turn the menu item ON, change the option to YES.

4.Exit the Program Mode by pressing the right switch. Both displays will read OFF.

How to Display “Use Time” Information

NOTE: This feature is used to determine the total amount of time that a fryer has been cooking.

1.Enter the program mode. See How to Enter the Program Mode on Page 3-10.

2.Press the left switch to display use time for the left side of a dual-vat unit. Press the right switch to display use time for a full-vat unit or the right side of a dual-vat unit.

3. To reset use time data to zero, while pressing one of the switches, press the same side's 1 and

2switches, then release them simultaneously.

NOTE: The simultaneous release of these three switches is critical. If not done correctly, data will not reset.

How to Display the Product Cycle Accumulator Information

NOTE: This feature keeps a running total of cooking cycles per product.

1.Enter the program mode. See How to Enter the Program Mode on Page 3-10.

2.Press the left or right switch.

3.For the left vat, press the switch. For the right or for a full-vat, press the switch. A running total of cooking cycles per product will be displayed.

4.To clear the accumulated times from computer memory, press either switch, then the switch.

3–14

Page 26 Page 28
Image 27
Page 26 Page 28
Contents OPERATOR’S Manual Frymaster H52 Series GAS Fryer Page General IntroductionComputer Information European Community CE Specific InformationWhat to do if your equipment arrives damaged Service Information General Installation Requirements Installation InstructionsNational Code Requirements Caster/Leg Installation Non-CE Standard For Incoming Gas Pressures Countries Categories GAS Connection to Gas LineCE Standard Gas Vat Converting to Another Gas TypeNon-CE Gas Conversion Kits CE Gas Conversion Kits for Units with Gas ValveFrypot Boil-Out Shutdown Operating Fryers With M100B Cooking ComputersDescription Introduction To The M-100B Cooking ComputerOperating the Computer on Full-Vat Fryers Viewing the Frypot Temperature Actual or Setpoint Operating the Computer on Split-Vat FryersCooking Product Full-Vat or Split-Vat Recovery Out of Range REC Lock M-100B Computer Problem Condition IndicatorsOpen Drain Valve Indication M-100B Computer Set-Up and Programming Instructions Probe Failure IndicationHow to Configure the Computer for Use on a Gas Fryer 1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Change the Computer’s Display LanguageHow to Change Computer Product/Temperature Displays How to Reset the Computer to the Factory Defaults How to Activate or Deactivate the Frypot BOIL-OUT Feature2 M-100B Computer Programming Mode How to Enter the Program ModeHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display the Product Cycle Accumulator Information How to Display Use Time InformationHow to Use the Filter Countdown Timer Introduction to the Analog Controller Operating Fryers With Analog ControllersC D E F G H I J K L M N Analog Controller High-Limit Check Page Filtering Operating the Built-In Filtration System Page Operating the Filter Unit Page Getting the Most Out of Your Filter Page Preventive Maintenance and Troubleshooting Preventive MaintenanceTroubleshooting REC Lock Troubleshooting Fryers with M100B ComputersIgnition Failure Display Remains Blank When ON/OFF Switches are Pressed Troubleshooting Fryers Equipped with Analog Controllers Did burners Troubleshooting Built-in Filtration System Pump does Not RUN
Top Page Image Contents